SB ACOUSTICS SB17CAC35-4 Ceramic Woofer Instructions
- June 1, 2024
- SB ACOUSTICS
Table of Contents
SB ACOUSTICS SB17CAC35-4 Ceramic Woofer
Product Specifications
- Nominal Impedance: 4 Ohm
- Free air resonance, Fs: 29.5 Hz
- DC resistance, Re: 3.1 Ohm
- Voice coil inductance, Le: 0.13 mH
- Sensitivity (2.83 V / 1 m): 90 dB
- Mechanical Q-factor, Qms: 4.70
- Effective piston area, Sd: 118 cm2
- Electrical Q-factor, Qes: 0.31
- Voice coil diameter: 35.5 mm
- Voice coil height: 16 mm
- Air gap height: 5 mm
- Total Q-factor, Qts: 0.29
- Moving mass incl.air, Mms: 15.2 g
- Force factor, Bl: 5.3 Tm
- Linear coil travel (p-p): 11 mm
- Equivalent volume, Vas: 37.8 liters
- Magnetic flux density: 1.0 T
- Compliance, Cms: 1.91 mm/N
- Magnet weight: 0.54 kg
- Mechanical loss, Rms: 0.6 kg/s
- Net weight: 1.56 kg
- Rated power handling: 60 W (IEC 268-5, T/S parameters measured on drive units that are broken in)
Product Usage Instructions
Installation
- Ensure the speaker is compatible with your audio system.
- Mount the speaker securely in a suitable location.
Connection
- Connect the speaker wires to the appropriate terminals on the speaker.
- Make sure the connections are secure to avoid any sound issues.
Operation
- Power on your audio system and adjust the volume to a moderate level.
- Play audio content and check for sound quality and balance.
FEATURES
- Vented cast aluminum chassis for optimum strength and low compression
- Geometrically reinforced ceramic cone for optimum piston operation and reduced break-up.
- Soft damping rubber surround for improved transient response
- Non-conducting fiberglass voice coil former for minimum damping
- Extended copper sleeve on pole piece for low inductance and low distortion
- CCAW voice coil for reduced moving mass
- Long-life silver lead wires
- Vented pole piece for reduced compression
Specification
| Nominal Impedance | 4 W | Free air resonance, Fs | 29.5 Hz |
|---|---|---|---|
| DC resistance, Re | 3.1 W | Sensitivity (2.83 V / 1 m) | 90 dB |
| Voice coil inductance, Le | 0.13 mH | Mechanical Q-factor, Qms | 4.70 |
| Effective piston area, Sd | 118 cm2 | Electrical Q-factor, Qes | 0.31 |
| Voice coil diameter | 35.5 mm | Total Q-factor, Qts | 0.29 |
| Voice coil height | 16 mm | Moving mass incl.air, Mms | 15.2 g |
| Air gap height | 5 mm | Force factor, Bl | 5.3 Tm |
| Linear coil travel (p-p) | 11 mm | Equivalent volume, Vas | 37.8 liters |
| Magnetic flux density | 1.0 T | Compliance, Cms | 1.91 mm/N |
| Magnet weight | 0.54 kg | Mechanical loss, Rms | 0.6 kg/s |
| Net weight | 1.56 kg | Rated power handling* | 60 W |
IEC 268-5, T/S parameters measured on drive units that are broken in
DIAGRAM
- (Blue) : on-axis
- (Green): 30° off-axis
- ( Red ) : 60° off-axis
Frequently Asked Questions
Q: What is the recommended power output for this speaker?
A: The speaker is rated for a power handling of 60W according to IEC standards.
Q: How should I position the speaker for optimal performance?
A: Place the speaker in a location that minimizes obstructions and allows sound to propagate freely.
Q: Can I use this speaker outdoors?
A: It is recommended to use the speaker in indoor environments to prevent damage from weather conditions.
Read User Manual Online (PDF format)
Loading......