Sure Electronics AA-JA32474 2 x 30 Watt Class D Audio Amplifier Board Instruction Manual

June 1, 2024
Sure Electronics

Sure-Electronics-logo

Sure Electronics AA-JA32474 2 x 30 Watt Class D Audio Amplifier Board

Sure-Electronics-AA-JA32474-2-x-30-Watt-Class-D-Audio-Amplifier-Board-
product-image

Specifications

  • Number of Channels: 2
  • Minimum Load Impedance: 8 Ohm
  • Efficiency: 89%
  • Nominal Power Requirement: 67W
  • Operating Voltage: 24V
  • Idle Power: 1.92W
  • Switching Frequency: 400kHz
  • Power Consumption: 17W
  • Standby (Low = inputs enabled): 9W
  • Mute (High = outputs enabled): 240mW
  • Standby Power: 3.3V

Product Information

  • The JAB3+ is an audio amplifier board integrated with high-performance Bluetooth 5.0 (Supporting APT-X HD) and ADAU1701 DSP. It comes in stereo 50W or 30W models and mono 100W or 60W models, suitable for portable Bluetooth speakers, digital crossovers, and DIY audio applications. The board supports Bluetooth input, 3.5mm AUX IN, and can be cascaded with other WONDOM standard amplifier boards to build audio 4.0/2.1 systems.
  • Four connectors for external potentiometers are pre-mounted on the board for easy control of the audio system. The JAB3+ also supports programming with SigmaStudio or remote control through APP or PC UI when connected to WONDOM ICP5 or higher versions.
  • Signal Level Sensor System, Power Management Circuit, and full protection features are equipped in the JAB3+ for lower power consumption.

Audio Performance

  • Amp Gain: 26dB
  • DSP Gain: 770dB
  • Input Sensitivity: 4mV
  • Filter Gain: 20dB
  • Cutoff Frequency: 96kHz
  • SNR: 48dB
  • THD+N: 10%
  • Input Impedance: 182 Ohm
  • Supported Sampling Rates: 10kHz
  • Output Noise Level: 1.94V
  • DC Offset Max output Level Crosstalk Separation: -60dB

Product Usage Instructions

  1. Ensure the board is powered by a 24V DC power supply.
  2. Connect your audio input source to either the Bluetooth input or the 3.5mm AUX IN.
  3. If using external potentiometers, connect them to the pre-mounted connectors for audio system control.
  4. If cascading with other amplifier boards, follow the appropriate setup guidelines.
  5. To program or remotely control the board, connect WONDOM ICP5 or higher versions and use SigmaStudio or the provided APP or PC UI.

Frequently Asked Questions (FAQ)

  • Q: What certifications are provided for the product?
    A: FCC, CE, and RoHS certifications are available for customers upon request. Test reports will be provided via email for customers making bulk purchases of MOV USD$10,000 or MOQ 500pcs.

  • Q: Can the JAB3+ be used to build a stereo system?
    A: Yes, the JAB3+ supports stereo configurations and can be cascaded with other boards to create stereo setups.

2 x 30 Watt Class D Audio Amplifier Board w DSP & BT 5.0 – JAB3+ (AA- JA32474)

Key Features

  • 3.60 x 2.70 Inches PCB Size
  • Battery Board Supported
  • Power Management Circuit
  • DSP & Bluetooth 5.0 Integrated
  • High Receive Sensitivity with RF power up to 9dBm and -90dBm
  • Supporting Various Audio Decode Formats as APTX, APTX HD, APTX-LL, SBC & AAC
  • Cascadable with Standard Amplifier Boards for Audio 4.0/2.1 System
  • Bluetooth Pairing Cancellation
  • External Control Potentiometers
  • Supporting ICP5 for PC UI control

Distributors

All Audi o Amplifier boards are complied with ROHS and they are pre- tested with our power supply solution to comply with FCC and CE. We could provide FCC, C E and RoHs certifications for customers’ convenience. The test re ports will be provided upon request s by e-mails only for customers who apply for bulky purchase  of MOV USD$10,000 or MOQ 500pcs.

Ready for: Contact Info
Email:info@wondom.com

Overview

  • JAB3+ is audio amplifier boards integrated with high performance Bluetooth 5.0 (Supporting APT-X HD) and ADAU1701 DSP, covering stereo 50W or 30W models and mono 100W or 60W models, suitable for portable Bluetooth speakers, digital crossover and DIY audio applications.
  • JAB3+ supports both Bluetooth input and 3.5mm AUX IN. Signal would be mixed and delivered to speaker output. Besides speaker output, JAB3+ supports cascading with other WONDOM standard amplifier boards to build audio 4.0/2.1 systems.
  • Four connectors for external potentiometers are pre-mounted on the board for easy control of audio system. As for the details, please take reference of ‘Function of Potentiometers’ part. In addition to hardware control, with the connection of WONDOM ICP5 or higher versions, JAB3+ supports programming with SigmaStudio or remote control through APP or PC UI.
  • Signal Level Sensor System, Power Management Circuit and full protection are equipped in JAB3+ for lower power consumption, higher efficiency and stable operation.

Electrical Specifications

Specifications typical @ +25℃, powered by 24V DC, unless otherwise noted. Specifications subject to change without notice.

Parameter Conditions Min. Typ. Max. Units
Number of Channels 2
Minimum Load Impedance 3.2 8 Ω
Efficiency 2 x 30W@8Ohm, 1kHz 89 %
Nominal Power Requirement @24V, 1kHz 67 W
Operating Voltage @1kHz, 8Ohm 12 24 26 V
Idle Power Signal detected 1.92 W
No Signal detected 1.68 W
Switching Frequency SD Floating@24V 400 kHz
Power Consumption 1/4 of max output power@8Ohm, 24V, 1kHz 17 W
1/8 of max output power@8Ohm, 24V, 1kHz 9 W
Control Standby (Low = inputs enabled) High-level Input Voltage 3.3

V
Low-level Input Voltage| –| –| 0.8| V
Mute (High = outputs enabled)| High-level Output Voltage| 3.3| | | V
Low-level Output Voltage| –| –| 0.8| V
Standby Power| SD short to GND, only when low power module available| –| 240| –| mW

Audio Performance

Specifications typical @ +25℃, powered by 24V DC, unless otherwise noted. Specifications subject to change without notice.

Parameter Conditions Min. Typ. Max. Units
Amp Gain @8Ohm, 20Hz – 20kHz 26 dB
DSP Gain SE1 (Single Amp) @8Ohm, 1kHz -60 0
SE2 (Line Output) @8Ohm, 1kHz -60 6.5 dB
Input Sensitivity 2 x 30W@8Ohm, 1kHz, 23.5dB 770 mV
Filter Gain Butterworth, Q= 0.707 4 dB
Cutoff Frequency HFP 0.25 2 kHz
LFP 20 kHz
SNR 2 x 30W@8Ohm, THD+N=1%, 25.8dB, A-weighting 96 dB
THD+N 5W@8Ohm, 1kHz,25.8dB 0.06 %
10W@8Ohm, 1kHz, 25.8dB 0.08 %
Input Impedance 10
Supported Sampling Rates 48 kHz
Output Noise Level A-weighting, Input Connected to GND, 25.8dB 182 uV
DC Offset 10 mV
Max output Level J7, Line Output Connector 1.94 dBu
Crosstalk Separation 20Hz-20kHz, Gain=26dB -60 dB

All parameters were tested with Rohde & Schwarz UPV audio analyzer (AES17 filter enabled) and Audio Precision AUX0025 filter. For authorized distributors and OEM customers who need more detailed performance graphs and parameter settings, please send an inquiry e-mail to us. (Not available for retail customers)

Block Diagram

Sure-Electronics-AA-JA32474-2-x-30-Watt-Class-D-Audio-Amplifier-Board-fig-
\(4\)

Notes:

  1. Please kindly be noted that there is no charging circuit equipped in JAB3+. If customers want to power JAB3+ with batteries, it is recommended to use WONDOM BCPB series.
  2. JAB3+ supports cascade with other WONODM audio amplifier boards to build audio 4.0/2.1 systems.
  3. Signal Level Sensor System has been employed in JAB3+ for low power consumption. JAB3+ will enter into standby mode when audio signal is not detected for long time (5min). Once audio signal is detected under this circumstance, JAB3+ will restart to work. It is not malfunction if JAB3 enters into standby mode.
  4. The basic cable package of JAB3+ contains: one power cable, one speaker cable. If you have special requirements of cables, please contact us at store@sure-electronics.com .

Function of Potentiometers

Functions of potentiometers based on specific applications

Port| Function| JAB3+S| JAB3+M| (JAB3+S)+ SAB| (JAB3+M)+ SAB
POT1| CH2 Gain| Gain of Line Output| Gain of Line Output| Gain of Power Sage of SAB| Gain of Power Sage of SAB
POT2| CH2 HPF| High-pass Filter of Line Output| High-pass Filter of Line Output| High-pass Filter of Power Sage of SAB| High-pass Filter of Power Sage of SAB
POT3| CH1 HPF or BPF| High-pass Filter of Speaker Output| Band-pass Filter of Speaker Output| High-pass Filter of Speaker Output of JAB3+| Band- pass Filter of Speaker Output of JAB3+
POT4| CH1 & CH2

Volume

| Volume of Speaker & Line Output| Volume of Speaker & Line Output| Overall Volume of JAB3+ & SAB| Overall Volume of JAB3+ & SAB
Note

  1. The speaker output (J10) of JAB3+ is defined as CH1; line output for cascading (J7) of JAB3+ is defined as CH2.
  2. JAB3+S refers to JAB3+ in stereo mode, namely 2 x 50 Watt Class D Audio Amplifier Board w DSP & BT5.0 – JAB3+ or 2 x 30 Watt Class D Audio Amplifier Board w DSP & BT5.0 – JAB3+; JAB3+M refers to JAB3+ in mono mode, namely 1 x 100 Watt Class D Audio Amplifier Board w DSP & BT5.0 – JAB3+ or 1 x 60 Watt Class D Audio Amplifier Board w DSP & BT5.0 – JAB3+. SAB refers to WONDOM Standard Amplifier Board.

3. HPF refers to High-pass Filter; BPF refers to Band-pass Filter. When CH1 is stereo output, the function of POT3 is HPF; when CH1 is mono output, the function of POT3 is BPF.
4. Four applications are exampled in this datasheet. For the functions of potentiometers when used in other applications, please contact us at store @sure-electronics.com.
5. Four connectors for connection with external potentiometers are pre- mounted on the JAB3+. If you want hardware control, please connect with the external potentiometers for adjustment.
Function| Range of Frequency
---|---
High-pass Filter (Stereo Mode)| 20Hz- 2kHz
High-pass Filter (Mono Mode)| 250Hz- 2kHz
Band-pass Filter| 60HZ-120Hz (High-pass)
200Hz-400Hz (Low-pass)

Sure-Electronics-AA-JA32474-2-x-30-Watt-Class-D-Audio-Amplifier-Board-fig-
\(5\)

Mechanical Dimensions

Sure-Electronics-AA-JA32474-2-x-30-Watt-Class-D-Audio-Amplifier-Board-fig-
\(6\)

Dimensions| A (inch/mm)| A1 (inch/mm)| B (inch/mm)| B1 (inch/mm)| D (inch/mm)
---|---|---|---|---|---
3.60/91.44| 3.30/83.8| 2.70/68.6| 2.40/61.0| 0.14/3.6

Notes:

  • All dimensions are typical in inches/mm, Height = 0.79inch / 20mm
  • Tolerance x.xx = ±0.02(±0.50)

Connections

Sure-Electronics-AA-JA32474-2-x-30-Watt-Class-D-Audio-Amplifier-Board-fig-
\(7\)

External LED Indicator

External Bluetooth Indicator Connector: J1, PH-2Pos-2mm

Pin Definition
1 LED-
2 LED+
  • When Bluetooth is paired, the LED will be ON;
  • When Bluetooth is searching, the LED will BLINK.

External Signal Detection Indicator Connector: J11, PH-2Pos-2mm

Pin Definition
1 LED-
2 LED+
  • When there is signal detected, the LED will be ON;
  • When there is no signal detected for 5min, the LED will be OFF.

Potentiometers
Four connectors are provided on the JAB3+ board for external potentiometers. The cables are included in the Functional cables kit for JAB3+ (AA-JA11117).

Power Supply
P ower Supply Connector: J8, Molex- 2Pos- 3mm

Pin Definition
1 VCC
2 GND

*Battery Board Connector:**
J6, PH- 4Pos- 2mm

Pin Definition
1 VCC
2 VCC
3 GND
4 GND

Audio Input

  • Bluetooth Input: U1
  • 3.5mm AUX IN Connector: J9, PH- 5Pos- 2mm
Pin Definition
1 RIN
2 AGND
3 LIN
4 NC
5 NC

You can find the 3.5mm AUX IN cable in the Functional cables kit for JAB3+ (AA-JA11117).

Extension Port
DSP Extension Port : J4, PH- 10Pin- 2mm

Pin Definition Pin Definition
1 GND 6 MP00
2 MP11 7 DATA
3 MP10 8 BCLK
4 MP06 9 LRCLK
5 MP07 10 +3.3V

This port can be used for I2S input and I2S output. Please note JAB3+ is set as master mode when using I2S. The mapping of ADAU1701 is as follows.

For I2S input:

Pin I2S Input ADAU1701
6 I2S DATA0 MP0
7 I2S DATA1 MP1
8 I2S BCLK MP5
9 I2S LRCLK MP4

For I2S output:

Pin I2S Output ADAU1701
2 I2S BCLK MP11
3 I2S LRCLK MP10
4 I2S DATAO0 MP6
5 I2S DATAO1 MP7

Besides, if you want to develop more functions, you can make use of Pin 4, 5, 6 of J4. Other positions are not available.

Audio Output

Speaker Output Connector:  J10, Speaker Output Connector

Pin Definition
1 ROUT1+
2 LOUT2-
3 ROUT1-
4 LOUT2+

Line Output Connector:
J7, PH-6Pos-2mm

Pin Definition
1 LOUT
2 NC
3 GND
4 GND
5 NC
6 ROUT

This port can be used to cascade with other WONDOM standard amplifier boards to build audio 4.0/2.1 system.

Control
BT Pairing Cancellation Connector: J3, PH- 2Pos- 3mm

Pin Definition
1 Cancel
2 +3.3V
  • When Bluetooth is paired, short  circuit ‘Cancel’ and ‘+3.3V’ to cancel pairing.
  • After cancellation, please release short circuit.

Standby and Mute Control Connector: J12, PH- 3Pin- 2mm

Pin Definition
1 STBY
2 GND
3 MUTE
  • Short circuit “STBY” and “GND” to enter into standby mode;
  • “Mute” is for control synchronization with the cascading amplifier board so that their control logic can be consistent. Do not short circuit “Mute” and “GND” when using JAB3+ separately.

Programming Connector: J5, PH- 6Pin- 2mm

Pin Definition Pin Definition
1 RST 4 WP
2 +5V 5 SCL
3 GND 6 SDA

This port is for connection with WONDOM ICP5 to achieve programming and remote control functions.

Sure Electronics

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals