ANONA SL2001 Holo Smart Lock User Manual
- June 1, 2024
- ANONA
Table of Contents
Anona Holo User Manual
Product overview
Please read this manual carefully before using the product and keep it in a safe place.
Package contents
Smart lock
Installing batteries
- Remove the front plate, pull the thumb turn, and install the batteries with the correct polarity.
- Place back the front plate.
Product usage
| Description | Indicator light status |
|---|---|
| Starting up | Flashing green |
| Awaiting binding/ Wi-Fi connecting | Flashing blue |
| Bound/Connected successfully | Solid green |
| OTA updating | Flashing blue |
| Low battery | Solid red |
| Description | Buzzer status |
| Abnormal status | Buzzer beeping |
| Description | Button operation |
| Entering binding mode | Press and hold the reset button for about 5 seconds |
Binding smart lock
-
Download and install the Anona app by scanning the QR code or finding “Anona” in the app store. https://www.anonasecurity.com/download
Note: A mobile phone with Android 5.0 or iOS 12.0 or later is required. -
Open the app and sign in your Anona account.
Tap icon “+” in the right upper corner and then follow the on-screen instructions to complete the binding, Wi-Fi connecting and calibrating process. .
Notes:
- This product only supports 2.4GHz Wi-Fi networks, 5GHz Wi-Fi networks are not supported.
- Before binding, ensure your phone is connected to the Internet and the Bluetooth is enabled. Also ensure the smart lock is in binding mode with indicator light flashing blue.
Compatible doors
This smart lock is only compatible with the single cylinder deadbolt.
Installing smart lock
Cautions
- Temperature for normal use of this product is-10°C to 55°C and temperature for storage of this product is -30°C to 70°C. Do not use or store this product in the environment at too high or too low temperature.
- This product is not waterproof. Do not expose the product to any liquid. Do not use the product in a humid environment.
- llustrations of the product, accessories, and user interface in the user manual are for reference purposes only. The actual product and functions may vary due to product enhancements.
Specifications
Product: Smart Lock
Model: SL2001
Item dimensions: 75mm × 75mm × 63mm
Input: 4 × AA battery
Wireless connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4GHz, Bluetooth® 5.4
FCC Caution.
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
FCC ID: 2BB7K-SL2001
ISED compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licenceexempt
RSS(s).
Operation is subject to the following two conditions:
- This device may not causeinterference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure statement
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your body.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Anona Security Technology
Limited is under license. Other trademarks and trade names are those of their
respective owners.
V1.0-20230822
Service: help@anonasecurity.com
For further information, please go to
www.anonasecurity.com
Manufacturer: Anona Security Technology Limited
Address: 8 The Green,Ste A Dover DE 19901, America
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>