DS18 JL-SBARHARNESS Plug and Play Harness for JL or JT-SBAR Overhead Audio Sound Bars User Manual

DS18 JL-SBARHARNESS Plug and Play Harness for JL or JT-SBAR Overhead Audio Sound Bars User Manual

Introduction

This is a cable kit that will help you more easily install your JL-SBAR soundbar on your JEEP JL / JLU / JT when you upgrade your sound system and add an amplifier and a light module (optional). This wiring includes everything you need to integrate the soundbar with the JEEP, this includes the connections for the ceiling courtesy lamp and everything you need to connect the 4 speakers, and the 4 tweeters with RGB lights to your system.

ATTENTION
Only works for Non-Amplified factory sound system.

What is included:

• Harness kit OFC with all factory style connectors and terminals
• Instructions Manual

What you will need:

• Any 4/5/6 Channels Amplifier.
• LED RGB Control module (LED-BTC).
• Sound bar for Jeep 11_ / JLU / JT (1L-SBAR).
• 4 x 8″ Speakers (NXL-8 recommended).
• 4 x 1.75″ Tweeters (PRO-TW4L recommended).

ATTENTION
Installation of mobile audio and video components requires experience with a variety of mechanical and electrical procedures. Although this manual provides general installation and operation instructions, it does not show the exact installation methods for your vehicle. If you do not have the required knowledge and experience to successfully complete the installation, consult an authorized dealer about professional installation service.

ATTENTION
Disconnect the negative post (Ground) of the battery before you start the installation. This helps avoid airbags coding and malfunctions, codes module malfunction or any electrical issues

OVERALL VIEW

AMPLIFIER SIDE INSTALLATION

1. RGB led lights from the soundbar: connect this to the LED-BTC (Sold separately)
2. This goes to the roof for the sound bar.
3. Soundbar speaker harness: connect this to the “Roof” amplifier (VVh: CH1+, Wh/Bk: CH1-, Gy: CH2+, G v/Bk: CH2-, Gr: CH3+, Gr/Bk: CH3-, Vt: CH4+, Vt/Bk: CH4-).

To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

• Black wire”BK” connected to battery Positive (+) 12V

• White Color Light “R”; “B” and “G” connected to battery Negative (-)

• Green Color Light “G” connected to battery Negative (-)

• Red Color Light “R” connected to battery Negative (-)

• Blue Color Light “B” connected to battery Negative (-)

• Purple Color Light “R” and “B” connected to battery Negative (-)

• Yellow Color Light”R” and “G” connected to battery Negative (-)

• Cyan Color Light “B” and “G” connected to battery Negative (-)

SOUNDBAR SIDE

• A. RGB LED light wire: connect this to each RGB LED lighting such as speakers, rings, grills, tweeters, and D518 Badge used for the soundbar.
• B. 12 pin Harness Connector: this goes to the DS18 roof harness from the amplifier side.

1. Speaker 1 connector: connect this to the speaker, Green: +, Green/Black: –
2. Speaker 2 connector: connect this to the speaker White: +, White/Black: –
3. Speaker 3 connector: connect this to the speaker Gray: +, Gray/Black: –
4. Speaker 4 connector: connect this to the speaker Violet: +, Violet/Black: –
5. Tweeters: connect this to each tweeter, Gray: +, Gray/Black: –

Final Steps:
This completes the installation of the JL-SBARHARNESS and you are ready to install everything else, refer to the installation manual of your Sound-bar and the amplifier for a more detailed procedure of the installation of each component.

FOR MORE INFORMATION PLEASE VISITDS18.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>