stollindustries AMBIANCE Fireplace Installation Guide
- June 1, 2024
- stollindustries
Table of Contents
stollindustries AMBIANCE Fireplace
Product Information
Specifications:
- Product: Stoll Fire Build-out Kit
- Warranty: 3 year limited warranty
- Materials Included: Self Tapping Screws, Face Panels (2), Vertical Supports (2), Horizontal Brackets (3), Rear Mounting Bracket (1), Top Cap/Shelf
Product Usage Instructions
Build-out Kit Assembly:
Shell Assembly:
- Lay the face panels (b) face down on a soft/non-abrasive surface.
- Attach the face panels together using the self-tapping screws.
- Connect both vertical supports (c) to the face panels through the provided slots.
- Fasten the vertical supports in place with self-tapping screws.
- Attach the rear mounting bracket (e) to the top of the vertical supports using the provided screws.
- Attach the three horizontal supports to the corresponding slots and cleats on the vertical supports.
Firebox Installation:
Install the firebox into the build-out kit following the manufacturer’s
instructions.
Mounting:
If desired, attach the build-out kit to the wall or structure behind it
using appropriate fasteners through the rear mounting bracket.
Shelf Assembly:
Attach the top cap/shelf (f) to the build-out kit by aligning the cutouts
on the back of the shelf with the vertical supports and sliding it down into
place.
Operation & Maintenance:
Your Build-out Kit is covered by a 3-year limited warranty. Refer to
www.stollindustries.com/resources for warranty claims and information.
Photos of Completed Products:
We encourage you to share images of your finished project by emailing
photos@stollindustries.com. Your project
may be featured on our social media or website.
Safety Information:
This product can expose you to chemicals including Carbon Black, which is
known to cause Cancer. Visit www.P65Warnings.ca.gov for more information.
FAQ:
- Q: Where can I find additional installation assistance?
A: For further help or information regarding installation, please contact your local dealer for assistance.
Thank you for purchasing a Stoll Fire Build-out Kit! We are confident this quality product will last you for years to come. If you need further help or additional information regarding installation, please reach out to your local dealer for assistance.
Included Parts & Tools
- A. Self Tapping Screws
- B. Face Panels: 2
- C. Vertical Supports: 2
- D. Horizontal Brackets: 3
- E. Rear Mounting Bracket: 1
- F. Top Cap/Shelf
Build-out Kit Assembly
Shell Assembly
Lay the face panels (b) face down on a soft/non-abrasive surface to ensure
they do not scratch. Using the provided self-tapping screws, attach the face
panels together. Screw hole locations are pre-drilled in each panel to ensure
proper alignment.
Standing the face panels upright, connect both vertical supports (c) to the
face panels through the appropriate slots. (Each vertical support has lasercut
slots cut that correspond with cleats on the face panels). Using a rubber
mallet, ensure cleats are fully seated in the corresponding slots
.
In the top corner of each side, fasten the vertical supports in place with the
provided self-tapping screws.
Attach the rear mounting bracket (e) to the top of the vertical supports.
Insert the cleats through the corresponding slots, and secure in place with
the provided self-tapping screws.
Attach the three horizontal supports to the corresponding slots and cleats on
the vertical supports behind the face panels. Two bars attach to the front of
the vertical supports above and below the opening, and one to the back of the
vertical supports below the opening. The two lower brackets will overlap
.
Firebox Installation
Following the manufacturers installation instructions for your specific
firebox, install the firebox into the build-out kit.
Mounting
If desired, attach the build-out kit to the wall or structure behind it by a
securing it through the rear mounting bracket with the appropriate fasteners
(not included).
Shelf Assembly
Attach the top cap/shelf (f) to the build-out kit by aligning the cutouts on
the back of the shelf with the vertical supports, and sliding it down into
place.
Operation & Maintenance
- Your Build-out Kit can be cleaned using a damp cloth and soap or mild household cleaner, or rubbing alcohol for tougher stains. To avoid damage to the finish, abrasive cleaning products and cleaners containing ammonia or other harsh chemicals should be avoided.
Warranty
Your Build-out Kit is covered by a year limited warranty. For more information, please visit www.stollindustries.com/resources. All warranty claims must be placed through your local dealer.
Photos of Completed Products
We would love to see pictures of your finished and installed project! Please
send images to
photos@stollindustries.com. High quality
images will likely be featured on our social media or website
!
WARNING: This product can expose you to chemicals including Carbon Black, which is known to the state of California to cause Cancer. For more information go to www.P65Warnings.ca.gov
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>