TOM AND JERRY Kitchen Chaos User Manual
- July 16, 2024
- TOM AND JERRY
Table of Contents
User Manual
Please read the instruction carefully before installation and use
TECHNICAL SPECIFICATIONS
Dimensions: D 2310%W 1752%H 1803 MM (with mallet holder)
Weight: 443KG
Power: 950W
PARTS LIST
| Name | Specification | Qty | Remark |
|---|---|---|---|
| User Manual | 1 | ||
| AC power cord | 1 | ||
| #6019 key | 1 | ||
| #6178 key | I | ||
| Puck | 120 | ||
| Mallet | 4 |
INSTALLATION AND ASSEMBLY
Overall Structure 1. Assenbling the Side Wall
1. Attach the two side walls with screws, side wall without opening in the
middle installed on the side with keyhole 2. Assembling the belt
1. Attach the belt with 4 screws, noted that the motor is on the inside. As
shown in the figure. 3. Assembling the Control Panel
1. Join the control panel on the both sides and playing field together.
(Note: 1.The console panel with buttons is on the right side of the
keyhole, the console panel without buttons is on the left side of the keyhole.
2.Connect the connector.) 2. Attach the fixing hardware to the table with
screws. (4 pieces of fixing hardware in total) 3. Assembling the Marquee
1. Attach the marquee to the score LED bracket slot with screws. 5.
Installing the Side Tower Assembly
1.Insert the side tower assembly into the opening in the side surface of the
table until the front of the side tower assembly touches the side surface of
the table.
(Note: connect the connectors before installation) 2. Attach the side tower
assembly to the table with eight screws.
MAIN COMPONENTS
1.Main components behind the front door under the control panel with buttons 2. Main components behind the side door.
CONTROL PANEL DISASSEMBLY INSTRUCTIONS
- 0pen the door under the control panel, loosen the screws, then rotate the caster hardware 90 degrees, and finally tighten the screws.
- Disconnect the connectors.
- Loosen the screws on the control panel on both sides.
GAME PLAY
- Insert coins.
- Press PLAY button to start the game.
- Players use the mallets to hit the puck towards the opponent’s goal to score points.
GAME MODE
Multi pucks mode: multi pucks are supplied to the puck outlet at one time, the left, center and right goals will open and blink randomly.
GAME SETUP
Display
Explanations
Press the Set button to enter the main menu
Set button: to return back to previous program
Service button: to finalize the selection
Test button: to save all changes made to the programs
Main menu Setup menu
1. Press Service button to select, press Test button to enter the menu, press
Set button to return back to main menu.
1.1 Coins per play
Press Service button to change coin or play, default: 4 coins per play. This
interface has enabled discount mode
Unable to change the number of coins and games after activating the Sale mode
This interface has no Sale mode enabled
0~9 Coin range
1~5 Play range
The game defaults to 2 coins per round
COIN3 PLAY?2 (discount mode): After activating the discount mode, players who
invest 3 game coins will receive 2 games (if players invest 2 game coins in
the discount mode, they will still only receive 1 game)
1.2 Game volume
Press Service button to select Game volume, press Test button to enter. 0~30
Play volume range:
0~30 BGM volume range
1.3 Reset
Press Service button to select whether reset the game (Restore all settings to
factory defaults) 1.4 Mode
Press Service button to select whether reset the game (Restore all settings to
factory defaults) Mode A: 60s
Mode B: 75s
Mode C: 90s
Mode D: 105s
Mode E: 120s
Test
2. Press Service button to select Test, press Test button to enter. 2.1
Aging test
Press Service button to select Yes or No, press Test button to enter. To exit
the aging test, press the Service button to select No, and then press the Test
button to confirm to exit the aging test.
2.21/0 test
Press Service button to select 1/O test
This interface shows that the conveyor belt current detection has been enabled
Current parameter detection of conveyor belt
1P: Detected that the passing current is 0.6A, and the detection light eye is
turned on
2P: Detected that the passing current is 0A, and the detection light eye is
not turned on
The current should be less than 1.5A (1.5A is the reference value)
Save
3. Press Service button to select the Exit with save.
On the main menu page, press Service button to select Exit with save, press
Test button to confirm the save.
3.1 Press Service button to select Exit without save
Exit
4.Press Service button to select Exit, press Test button to confirm, and
return to the main interface.
ERROR CODES AND TROUBLESHOOTING GUIDE
| ERROR CODES | ERROR DESCRIPTION | TROUBLESHOOTING GUIDE |
|---|---|---|
| E01 | IP Goal (L) motor error | 1,The goal is stuck. |
2,Check to see if goal motor is functioning correctly
3,Check to see if goal motor sensor is functioning correctly
E02| I P Goal (C) motor error| 1, Same as above
E03| I P Goal (R) motor error| 1, Same as above
E04| 2P Goal (L) motor error| 1, Same as above
E05| 2P Goal (C) motor error| 1, Same as above
E06| 2P Goal (R) motor error| 1, Same as above
E07| IP Puck Lift Assembly Error| 1,Puck lift tunnel has a puck jam
2,Check the puck lift motor
3,Out of pucks
4,Check the puck lift sensor
E08| 213 Puck Lift Assembly Error| 1, Same as above
E09| RS-485 Error| 1, Check to see if 10 board to 485 cable is not connected
E10| I P Goal (L) sensor error| 1,Goal (L) sensor malfunction
2,The goal (L) sensor is dirty.
3. Receiver and transmitter are not aligned
E11| IP Goal (C) sensor error| 1, Same as above
E12| IP Goal (R) sensor error| 1, Same as above
E13| 2P Goal (L) sensor error| 1, Same as above
E14| 2P Goal (C) sensor error| 1, Same as above
El5| 2P Goal (R) sensor error| 1, Same as above
El6| Out of Tickets| 1,All tickets have been dispensed
2,Loss of communication with ticket dispense
El7| IP Belt Error| 1,The belt is too tight or deformed, resulting in
excessive resistance
2,The belt is stuck.
E18| 2P Belt Error| 1, Same as above
E19| Coin Mech Error| 1, The Coin Mech DIP switch is in the
wrong position
E20| Service Error| 1, Contact customer service
E21| Motor drive board
communication error| 1. The communication between the 10 board and the motor
drive board is faulty
Wiring Diagram
For parts or support, please contact:
|
---|---
spares@bandainamco.co.uk|
support@bandainamco.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>