XMCOSYplus Low Voltage Mushroom Lights User Manual

Low Voltage Mushroom Lights
User Manual

Can’t connect? Need help?
Email:service.2@xmcosy.com

INTRODUCTION

Thanks for choosing XMCOSY+ Low Voltage Mushroom Lights.
Please read the user manual carefully and keep it for future reference.
SAFETY INSTRUCTIONS
Read and follow all safety instructions before installing the low voltage mushroom lights

• Sockets used to power mushroom lights should comply with all national and local electrical codes. If you are unsure of compliance requirements, please consult your local electrician.
• Do not use in water. Please connect power cords in deep together and tighten the protective cover. Especially for the interface at the end, please be sure to put on the protective cover. Keep the plug and socket dry.
• Please keep children away from these lights
• Keep lights away from flammables and fire sources.
• Avoid placing the lights near potentially dangerous sources

DO NOT EXCEED RATED CAPACITY.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located for operating in conjunction with any other antenna or transmitter.

SPECIFICATIONS

PACKAGE CONTENTS

1. Mushroom Light * 4
2. Aluminum Light Cap* 4
3. Aluminum Ground Stake* 4
4. 8.2FT Light Cable* 4
5. 13.1 FT Extension Power Cable * 1
6. 36W Power Adapter * 1
7. User Manual * 1

Notes:
After unpack;ng, please check the product accesso,;es. If there are any m;ss;ng or damaged accessor;es, please contact us as soon as poss;ble, and our customer serv;ce
team wm solve ;t ;n Ume. service.2@xmcosy.com

ASSEMBLE

Step-2
Connect the light cables in turn.

1. Align the positioning point.
   Notes:
   1. If the connectors are not aligned, the color of the mushroom lights Will be different or be inconsistent with the color setting in the APP 2. Without the waterproof cover, the light cable may submerge in water, which will cause a short circuit.
   Step·3 Connect the installed mushroom lights and the light cables in tum. Step -4
   1. Connect the extension power cable to the light cable & power adapter.
   2. Plug the power adapter into the power outlet.

BUTTON FUNCATION INTRODUCTION

Button Function Introduction:

1. Long press – Enter the APP connection & network mode. Long press the button for 5S, the light flashes quickly. and the product enters the distribution network mode.
   (When the product is used for the first time, it will automatically enter the network distribution state after connecting to the power supply, without pressing any
   buttons.)

2.  Short press – ON/OFF & Change scene modes 8 modes(4 kinds of warm white and 4 kinds of color light) Short pressing the button, the mode changes in turn as follows:

• ON(Gorgeous}
• Good night
• Reading
• Working
• Leisure
• Grassiand
• Colorful
• Dazzling
• Gorgeous
• OFF

For more scene modes and functions of the product, please connect to the XMcosy APP.

SERVICE & WARRANTY

Thank you for your support of XMCOSY+! XMCOSY+ provides a regular 1-Year Warranty.
   Not Satisfied?
If there is any problem with our product while using, Please Contact service.2@xmcosy.com
We will provide you with a 100% Satisfied Solution!
Satisfied?
We are glad that you didn’t encounter any problems with our low voltage mushroom lights. XMCOSY+ is committed to providing better products and service, so we provide an additional 1-year warranty. Please Email to register a 2-YEAR-WARRANTY warranty@xmcosy.com or scan the QR code

mailto:warranty@xmcosy.com

APP DOWNLOAD & REGISTRATION

Step 1: Download the XMcosy App from App Store or Google Play.

https://a.smart321.com/xmcosysmart

Step 2: Register

1. Enter your mobile phone

2. Enter the verification code. number or email address.
   

3. Create a password and Log in the App.

4. Please enable the XMcosy App to get your Bluetooth while using the App.

DISTRIBUTION NETWORK & APP CONNECTION

Step 1: Plug – In Plug XMCOSY+ smart mushroom path lights power adapter into any standard outlet.

Notes:

1. After power on, the light will automatically enter the connecting state (fast blinking);
2. If there is no connection after 3 minutes, the indicator lights will remain on. If you want to add a device at this time, you need to press and hold the power button on the controller for about 5 to 7 seconds until the lights blink rapidly.

Step 2: Register

1. Click the “+” in the home page upper right corner. The devices in the connecting state will be displayed at the top of the page. Click “Add”.

2. Click the device you want to add and please make sure that the network you connected is 2.4GHz.

3. Fill in your 2.4GHz network name and password, then click “Next”.

4. The product starts to connect until it is 100% completed.
   Please keep the router, mobile phone, and product as close as possible to ensure a good reception signal.

5. After you edit the product name and save it, click “Done” at the top right.
   Congratulation!
   Now you can use XMcosy App to cont,ol you, mush,oom i;ghts.

Tips:

1. The device name will be used again when paired to Amazon Alexa & Google Home for voice control.
2. The device name is suggested to consist of English words and Arabic numerals, please do not use special characters.

APP FUNCTIONS

WARM WHITE MODE & COLOR MODE
You can choose to turn on the mushroom lights in calor light or warm white light.
RGB Color Mode

• Color Wheel – Sitde the color wheel Up and down to adjust the color of the lights from a broad spectrum of colors. Drag the button on the wheel from right 10 fe to adjust the color temperature.

• Brightness – Slide the bightness bar to adjust the brightness from 1% 10 100%.

• Default Color – There are 7 default colors, you can click the round color tcone to choose a default color.
  Warm White Mode

• Brightness – Sude the “brightness” bar to adjust the brightness of low votage mushroom lights from 1% to 100%, you can freely brighten os dim the lights.

APP FUNCTIONS

• Scene Mode:
  XMcosy App has a scene selection function. Press the scene button toente the scene selection interface. You can choose your favorite scenes from 32 default scenes.
  You also can customize a new scene based on your favorite

• Music Sync Mode: The low voltage mushroom lights react in real-time when your app detects the songs.
• Plan: You can set the time and customize favorite light mode when you fall asleep/wake up

OTHER FUNCTIONS

• Schedule: Tu rn on/off automat,cally at preset t,mes.
• Left Time: The 1;ghts wrn turn off automaUcally after the countdown.
• Power-on Behavior: Power Memory mode.

ALEXA PAIRING INSTRUCTION

1. Download the Ama,on Alexa APP Search the keywo,ds”Ama,on Alexa” in the App Sto,e to, iOS device and in the Google Play to, And,oid device.

2. Sign in or register a new account

3. Pair the Amazon Alexa APP to Ama,on Echo Device (follow the Ama,on Echo User Manual)

4. Log in your Amazon Alexa APP
   Important tip5’please make sure the “XMcosy” app, Ama,on Alexa APP “Ama,on Echo” are connected to the same Wi-Fi network.

5.  Enable “XMcosy” skill In Ale,a APP
   a. CIiek “Skills & Games” In the MORE MENU on the Alm APP’s home page.
   b. In the popup page, input “xmcosy” in the search bar, click “XMcosy” in the search result and click” ENABLE TO USE” in the popup page to enable the skillsc. Click “Agree and link”, then “Your XMcosy account has been successfully linked”.![XMCOSYplus Low Voltage Mushroom Lights

• Scene Mode6](https://manuals.plus/wp-content/uploads/2022/11/XMCOSYplus-Low- Voltage-Mushroom-Lights-Scene-Mode6.png)

  6. Enjoy Amazon Alexa Control
     Now with Amazon Alexa, you can take control the mushroom lights by asking it to change colors, turn lights on and off by using simple commands.
     For example, using these Alexa commands below:
     “Alexa, Turn on/off {Specific light)”
     “Alexa, Set the {Specific light) to green”
     “Alexa, Set the {Specific light) to red”
     “Alexa, {Specific light) lights fifty”
     “Alexa, {Specific light) out”
     Tips: {Specific light) is the device name you named on XMcosy APP.

GOOGLE ASSISTANT PAIRING INSTRUCTION

1. Download the APP Search “Google Home” in the App Store for iOS device and in the Google Play for Android device to install.

2. Sign in or register a new account

3. Pair the Google Home APP to Google Home Device (follow the on-screen steps)

4. Link XMcosy account in set up devices a. Click the “4′ icon in the upper left corner of home page, then click “set up device”.
   Important tips: please make sure the XMcosy app, Google Home APP and Google Home devices arc connected to the same Wi-Fi network.
   b. Click “Works with Google” e. Input “XMcosy” in the search bar. d. In the new window, select your XMcosy account’s region, input your XMcosy account and password, then click “Next Step” and “Authorize”.
   

5. Enjoy Google Home Control
   Now you can take control the smart mushroom lights through Google Home by asking it to change colors, turn lights on and off by using simple commands.
   For example, using these voice commands below: “Google, Turn on/off (Specific light)” “Google, Set the (Specific light) to green” “Google, Set the (Specific light) to red” “Google, (Specific light) lights fifty” “Google, (Specific light) out”
   Tips: (Specific light) is the device name you named on XMcosy APP.

TROUBLESHOOTING

1. Why the colors of lights are different or can’t respond to the same color in the APP?| The cables are connected Incorrectly. Please check all connectors and connect  them by aligning the point. (Include the connection to thepower controller.)
2. Could the power adapter hold more than 6 lights?| No. The power adapter is 36W max and only can hold 6 lights in total.
For more lights connecting, please contact XMCOSY+ Customer Service Team [service.2@xmcosy.com]
3. The lights can’t connect to the APP.| 1.Please update the APP to the newest version.
2.Please turn on Bluetooth, 2.4GHz Wi-Fi, mobile data, and locations when connecting the devices.
3.Please try to connect the phone with a hotspot rather than Wi-Fi to see whether its the problem with Wi-Fi.
4.If the routing security level is very high or incompatible with the APP, it will cause
the problem of can’t connecting to the APR Please lower the security level of your router to make it compatible with XfAcosY APP. Or send us your router model for further solutions.
4. Home network is 5GHz.| The wall penetration capability of 5.0GHz is weaker than 2.4GHz, which means that the outdoorsignal of 5.0GHz is worse than 2.4GHz. Therefore, most smart devices support 2.4GHz networks or dual- frequency networks of 2.4GHz and 5.0GHz. You can log in to the management page of your router and change the SSIDs of the 2.4 GHz and 5 GHz networks to differentiate them.

CONTACT

For questions, assistance, or support,
Please Contact: service.2@xmcosy.com or scan to email

MAILTO:service.2@xmcosy.com?subject=Need Help for XMCOSY+ Smart
Mushroom Lights&body=Problem:
• Required Information

1. Amazon Order ID
2. Product Model NO.
   XMCOSY + Customer Service Team will reply within 24 hours.
   For more info. or news about XMCOSY+, pis follow XMCOSY+ social website. @XMCOSY+ @XMCOSY @xmcos

If there is any problem with our product while using

YOU DON’T NEED TO RETURN IT TO AMAZON
WE WALL PROVIDE YOU WITH 4 100% SATISFIED SOLUTION
XMCOSY+ Customer Service
service. 2@xmcosy.com
<Ncosy*
COSY
Lighting Expert.Brighten up Your Life

References

• SAA HOME - Swiss Aerobatic Association

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>