Z-WAGZ ZWBCMGM BCM Connected Module Adapter Instruction Manual

June 1, 2024
Z-WAGZ

Z-WAGZ ZWBCMGM BCM Connected Module Adapter

Product Information

Specifications

  • Product Name: Z-WAGZ OE Light Flash Module
  • Control Type: BCM-Controlled
  • Compatibility: GM and Ford Vehicles
  • Installation Type: Plug & Play
  • Optional Accessory: I/O Button Harness
  • LED Indicator: On-board LED for status indication

Product Usage Instructions

Ford Vehicle Installation

  1. Locate the BCM unit as per the provided chart.
  2. With the vehicle OFF, disconnect the (2) circled plugs from the BCM.
  3. Connect the male side of each T-Harness to the BCM and the removed plugs into the female side of the Z-WAGZ BCM harnessing.
  4. Connect the Z-WAGZ BCM unit to the 22-pin connector.
  5. Securely tie-wrap the unit to another harness if desired.
  6. Refer back to page 1 for operation instructions.

GM Vehicle Installation

  1. Locate the BCM unit as per the provided chart.
  2. With the vehicle OFF, disconnect the (4) highlighted plugs.
  3. Connect the male side of each T-Harness to the BCM and the removed plugs into the female side of the Z-WAGZ BCM harnessing.
  4. Connect the Z-WAGZ BCM unit to the 22-pin connector.
  5. Securely tie-wrap the unit to another harness if desired.
  6. Refer back to page 1 for operation instructions.

Frequently Asked Questions

Q: How do I activate the Z-WAGZ unit?

A: To activate Z-WAGZ, follow these steps:

  • Press and HOLD the high beam lever for 5 seconds OR
  • Press and HOLD the provided push button for 3 seconds OR
  • Send a latched 12v (+) signal to the blue wire

Q: How do I switch between different patterns?

A: To switch patterns, follow these steps:

  • To switch to Pattern 2, engage either turn signal and then press and HOLD the high beam lever for 5 seconds OR press & release the provided push button.
  • To switch to subsequent patterns, repeat the process above.

Q: How do I deactivate the Z-WAGZ unit?

A: To deactivate Z-WAGZ, simply press and HOLD either the high beam lever or the provided push button.

Plug & Play, BCM-Controlled, OE Light Flash Module

Thank you for purchasing a genuine Z-WAGZ unit, the simplest BCM-module for flashing OEM lights with a press of a button. This unit comes pre-programmed with 8 different light patterns, some for halogen systems & some for LED systems – see below for full operation information including on-board LED status.

Z-WAGZ-ZWBCMGM-BCM-Connected-Module-Adapter-FIG-1

Operation for Ford and GM vehicles is the same:

  1. Install the Z-WAGZ unit to the OE BCM unit. Follow instructions on page 2 (for Ford) or 3 (For GM).

  2. Turn Ignition ON (Ignition must be on for proper operation). Leave vehicle in Park.

  3. To activate Z-WAGZ:
    Press and HOLD the high beam lever (5 sec) OR
    Press and HOLD the provided push button (3 sec) OR
    Send a latched 12v (+) signal to the blue wire (designed to be extended for OE up-fitter switches)
    Pattern 1 will begin to flash. Once pattern 1 begins, the hazards in the gauge cluster will blink 1 time, indicating Pattern 1 h as been selected and the LED on the unit will blink BLUE. See chart for remaining pattern color indication.

  4. To switch to Pattern 2: (Pattern 1 must be currently active)
    Engage either turn signal, then press and HOLD the high beam lever once more (5 sec). OR
    Press & release the provided push button
    The hazards will blink twice indicating Pattern 2 has been selected. Repeat this process to switch to the next pattern.

  5. To deactivate Z-WAGZ:
    Press and HOLD the high beam lever OR
    Press and HOLD the provided push button OR
    Release 12v (+) signal to the blue wire (if connected this way)

NOTES

  • Vehicles equipped with LED lights should use LED patterns. Vehicles equipped with standard bulbs should use bulb patterns.
  • Drive Mode (anything outside of PARK gear) will emit its own, separate pattern from whatever pattern is currently selected. This is a limitation of the vehicle and how light data is handled when not in PARK gear.
  • Not all lights on the vehicle are necessarily used, some lights are not controllable via BCM CAN data.
  • Z-WAGZ will retain the last used pattern, even after being disconnected from the BCM (if ever).
  • When in Drive Mode, turn signals, headlights & reverse lights will override pattern flashing, until turned off again.
  • When on some patterns, in some vehicles, the reverse camera image may show up/flash on the OE screen (if equipped). This is a factory limitation and is normal. If you want to avoid this, use a pattern which removes the reverse light flashing.

Ford Vehicle Installation

  1. Locate the BCM unit. The chart below indicates the BCM location in various vehicles.
  2. With the vehicle OFF: disconnect the (2) circled plugs shown. Connect the male side of each T-Harness to the BCM and the (removed) plugs into the female side of the Z-WAGZ BCM harnessing. These connectors can only fit in one place and connect in one way.
  3. Connect the Z-WAGZ BCM unit to the 22-pin connector, tie-wrap the unit to another harness if desired.
  4. Return to page (1) for operation instructions.

Z-WAGZ-ZWBCMGM-BCM-Connected-Module-Adapter-FIG-4

GM Vehicle Installation

  1. Locate the BCM unit. The chart below indicates the BCM location in various vehicles.
  2. With the vehicle OFF: disconnect the (4) highlighted plugs shown. Connect the male side of each T-Harness to the BCM and the (removed) plugs into the female side of the Z-WAGZ BCM harnessing. These connectors can only fit in one place and connect in one way and are color matched to the OE plugs.
  3. Connect the Z-WAGZ BCM unit to the 22-pin connector, tie-wrap the unit to another harness if desired.
  4. Return to page (1) for operation instructions.

Z-WAGZ-ZWBCMGM-BCM-Connected-Module-Adapter-FIG-5

BCM

Z-WAGZ-ZWBCMGM-BCM-Connected-Module-Adapter-FIG-6

GM LED Status / Patterns

START-UP INDICATION
Description| LED Status| More Information
Initial Wake Up| Blinks BLUE (1 time)| —
Unit recognizes CAN bus| Blinks BLUE (3 times)| Upon CAN data wake
Unit detects ACC info| Blinks BLUE (1 time)| Upon Turning Ignition ON
Unit detects GEAR info| Blinks VIOLET (1 time)| Upon switching gears
Unit detects HIGH BEAM press OR External button press| Solid BLUE| Upon pressing High Beam lever or provided push button
No response from vehicle/CAN| Solid OR Blinks RED| While Z-WAGZ is activated
PATTERN INDICATION
Description| LED Status| More Information
Pattern 1| BLUE, off, BLUE, off| BASE PATTERN (LED PATTERN)
Pattern 2| RED, off, RED, off| BASE PATTERN + HIGH BEAMS (LED PATTERN)
Pattern 3| BLUE, RED, BLUE, off| WATERFALL PATTERN (LED PATTERN)
Pattern 4| RED, BLUE, RED, off| BLINK 2x PATTERN (LED PATTERN)
Pattern 5| BLUE, off, RED, off| BASE PATTERN (NO REV LIGHT) (LED PATTERN)
Pattern 6| BLUE&RED, off, BLUE&RED, off| BASE PATTERN (NO LOW BEAM) (LED PATTERN)
Pattern 7| BLUE, BLUE&RED, BLUE, off| BASE PATTERN (NO LOW BEAM, NO REV) (LED PATTERN)
Pattern 8| RED, BLUE&RED, RED, off| BASE PATTERN SLOWER (BULB PATTERN)
Pattern 9| BLUE, off, BLUE&RED, off| BASE PATTERN + HIGH BEAMS SLOWER (BULB PATTERN)
Pattern 10| RED, off, BLUE&RED, off| WATERFALL PATTERN SLOWER (BULB PATTERN)
Pattern 11| BLUE&RED, BLUE, BLUE&RED, off| BLINK 2x PATTERN SLOWER (BULB PATTERN)
Pattern 12| BLUE&RED, RED, BLUE&RED, off| BASE PATTERN (NO REV LIGHTS) SLOWER (BULB PATTERN)
Pattern 13| BLUE, RED, off, off| BASE PATTERN (NO LOW BEAM) SLOWER (BULB PATTERN)
Pattern 14| RED, BLUE, off, off| BASE PATTERN (NO REV or LOW) SLOWER (BULB PATTERN)
POWER CONSUMPTION
Current Draw Active:| 100mA MAX|
Current Draw idle:| 4mA MAX|
Trigger wire act:| 0V|
Trigger wire idle:| 3.3V|
Current limit:| 10mA|

FORD LED Status / Patterns

START-UP INDICATION

Description| LED Status| More Information
Initial Wake Up| Blinks BLUE (1 time)| —
Unit recognizes CAN bus| Blinks BLUE (3 times)| Upon CAN data wake
Unit detects ACC info| Blinks BLUE (1 time)| Upon Turning Ignition ON
Unit detects GEAR info| Blinks VIOLET (1 time)| Upon switching gears
Unit detects HIGH BEAM press

OR External button press

| Solid BLUE| Upon pressing High Beam lever or provided push

button

No response from vehicle/CAN| Solid OR Blinks RED| While Z-WAGZ is activated
PATTERN INDICATION
Description| LED Status| More Information
Pattern 1| BLUE, off, BLUE, off| BASE PATTERN (LED PATTERN)
Pattern 2| RED, off, RED, off| BASE PATTERN + HIGH BEAMS (LED PATTERN)
Pattern 3| BLUE, RED, BLUE, off| BASE PATTERN + MIRROR BLINKERS (LED

PATTERN)

Pattern 4| RED, BLUE, RED, off| BASE PATTERN + MIRROR BLINKERS + HIGH BEAMS (LED PATTERN)
Pattern 5| BLUE, off, RED, off| BASE PATTERN (NO REV LIGHT) (LED PATTERN)
Pattern 6| BLUE&RED, off, BLUE&RED, off| BASE PATTERN BACK SIDE LIGHTS SLOWER

(BULB PATTERN)

Pattern 7| BLUE, BLUE&RED, BLUE, off| BASE PATTERN + ALL LIGHTS SLOWER (BULB PATTERN)
Pattern 8| RED, BLUE&RED, RED, off| BASE PATTERN + ALL LIGHTS + MIRROR BLINKERS SLOWER (BULB PATTERN)
Pattern 9| Off, BLUE, off, BLUE&RED| BASE PATTERN + ALL LIGHTS + HIGH BEAM

SLOWER (BULB PATTERN)

Pattern 10| Off, RED, off, BLUE&RED| BASE PATTERN + ALL LIGHTS + HIGH BEAM + MIRROR BLINKERS SLOWER (BULB PATTERN)
POWER CONSUMPTION
Current Draw Active:| 100mA MAX|
Current Draw idle:| 4mA MAX|
Trigger wire act:| 0V|
Trigger wire idle:| 3.3V|
Current limit:| 10mA|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals