IFIXIT Nintendo DS Lite Wi-Fi Antenna Replacement User Guide
- June 4, 2024
- IFIXIT
Table of Contents
Nintendo DS Lite Wi-Fi Antenna Replacement
Replacement of the Nintendo DS Lite Wi-Fi antenna.
Written By: Matthew Newsom
This document was generated on 2022-05-04 02:13:25 AM (MST).
INTRODUCTION
Replace the Wi-Fi antenna in your Nintendo DS Lite.
TOOLS:
- Phillips #00 Screwdriver (1)
- Push Pin (1)
- Spudger (1)
- Tri-point Y1 Screwdriver (1)
Step 1 — Battery
Unscrew the Phillips screw securing the battery cover to the lower case.
The screw remains captive to the battery cover.
Pry the battery cover upward with a spudger or fingernail, and lift out of the
lower case.
Step 2
Wedge the edge of a spudger in between the side of the battery and the
lowercase housing and pry upward to dislodge the battery.
Remove the battery from the DS Lite.
Step 3 — Lower Case
Use the tip of a spudger to pry both rubber feet off the DS Lite.
Remove the following screws securing the lower case to the body of the DS
Lite:
Two 4.3 mm gold Phillips screws
One 3.9 mm black Tri-Wing screw
One 3.3 mm silver Phillips screw
Three 5.5 mm silver Tri-Wing screws
Step 5
Remove the cover from the Game Pak slot before continuing.
Insert the edge of a spudger in between the lower and upper case near the top
right corner of the DS Lite.
Carefully run the spudger along the right edge of the DS Lite, creating an
opening in the process.
Continue running the spudger along the backside of the DS Lite until the
majority of the lower case has been separated from the upper case.
Step 6
Lift the lowercase away from the rest of the DS Lite.
Pull carefully. Some units are sealed with adhesive, and pulling too hard can
damage the power switch.
When reassembling, make sure that the power switch and volume sliders are
properly aligned with the switches on the motherboard.
Step 7 — Trigger Buttons
Lift both trigger buttons out of the DS Lite.
The trigger buttons are held in very loosely by small metal pegs and springs.
Don’t lose track of these pieces.
The second picture shows the correct configuration of the trigger assembly for
reassembly purposes.
Step 8 — Wi-Fi Board
Use the flat edge of a spudger to pry the Wi-Fi antenna connector straight up
from its socket on the Wi-Fi board.
Step 9
Use the flat edge of a spudger to pry the Wi-Fi board connector straight up
from its socket on the motherboard.
Step 10
Use the flat edge of a spudger to separate the right edge of the Wi-Fi board
from the motherboard.
The Wi-Fi board is secured to the motherboard with a layer of adhesive.
Remove the Wi-Fi board from the DS Lite.
Step 11 — Motherboard
Use the flat edge of a spudger to pry the microphone connector straight up
from its socket on the motherboard.
Step 12
In the following steps, you must pull the antenna cable between the DS Lite
game cartridge reader and the motherboard. Pull slowly and stop when you feel
resistance to avoid damaging the cable or motherboard.
Position the antenna cable with its connector facing up and away from the
motherboard using a spudger to hold it down lightly in the gap between chips
on the motherboard.
Slowly and carefully pull the antenna cable until the cable connector is under
the DS Lite game cartridge reader.
Continue pulling the cable until the cable connector comes out from under the
game cartridge reader on the right side.
When reassembling and attempting to feed the antenna cable back under the game
cartridge reader, the cable may kink or become difficult to feed through. If
so, try feeding a piece of thread through first; then, tie the thread to one
end of the cable connector and pull it through, guiding it past any
obstructions.
Step 13
Use your fingernail or the edge of a spudger to carefully flip up the
touchscreen ribbon cable retaining flap.
Make sure you are flipping up the retaining flap, not the socket itself.
Use the tip of a spudger to pull the touchscreen ribbon cable straight out of
its socket.
Step 14
Remove the two 3.4 mm Phillips screws securing the motherboard to the upper
case.
Step 15
Open the display enough to use your finger to push the front edge of the
motherboard up and away from the upper case.
Do not try to remove the motherboard, as it is still connected to the upper
display via the upper LCD ribbon cable.
Step 16
Use your fingernail or the flat edge of a spudger to carefully flip up the
upper LCD ribbon cable retaining flap.
Make sure you are flipping up the retaining flap, not the socket itself.
Pull the motherboard away from the DS Lite to separate the upper LCD ribbon
cable from the socket on the motherboard.
Remove the motherboard from the DS Lite.
Now you may open the retaining flap for the lower LCD screen in the same way
and separate the lower LCD screen from the motherboard.
Step 17 — Upper Case
Remove the two 8.3 mm Phillips screws securing the upper case to the display
assembly.
Step 18
Pull the upper LCD ribbon cable to the right, through the slit in the case.
Push the ribbon cable down through the slit.
Step 19
Slowly lift the upper case away from the display, making sure the ribbon cable
does not get caught.
Step 20
Once the ribbon cable is free from the upper case, pull the antenna and Wi-Fi
cables through the hole in the upper case.
Remove the upper case from the DS Lite.
Step 21 — Rear Display Bezel
Use a push pin to remove the four plastic screw covers on the front bezel.
Step 22
Remove the four 3.4 mm Phillips screws securing the rear display bezel to the
front display bezel
Step 23
Use the edge of a spudger to pry both rubber pads out of the front display
bezel.
Step 24
Using two hands, gently slide the rear bezel upwards.
The rear bezel will move only about 2 mm.
Step 25
Insert a spudger in the gap between the front and rear display bezels and pry
the front bezel away from the rear bezel.
Lift the rear display bezel away from the display assembly.
Step 26 — Wi-Fi Antenna
Use the tip of a spudger to pry both speakers up from their housing and place
them on the back of the LCD.
The speakers have magnets that will hold them together, helping to keep them
out of the way for later steps.
Step 27
Starting in the top right corner, use both hands to slowly separate the LCD
from the front display bezel.
Continue separating along the top and left edges of the LCD.
Finally, push the LCD up and away from the front display bezel.
Do not try to remove the LCD yet, as it is still connected to the front
display bezel via the LCD ribbon cable.
Step 28
Lift the Wi-Fi antenna up, and pull its cable through the hole in the front
display bezel.
Remove the Wi-Fi antenna from the display assembly.
© iFixit — CC BY-NC-SA
www.iFixit.com
Nintendo DS Lite Wi-Fi Antenna Replacem…
References
- Amazon.com: Officemate Push Pins, Clear, 200 Count (35711) : Office Products
- iFixit: The Free Repair Manual
- store.ifixit.fr/products/phillips-00-screwdriver
- store.ifixit.fr/products/spudger
- store.ifixit.fr/products/tri-point-y1-screwdriver
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>