Arlo Pro 4 Go 2 Solar Panel Charger User Guide
- June 2, 2024
- Arlo
Table of Contents
Arlo Pro 4 Go 2 Solar Panel Charger User Guide
Quick Start Guide
Solar Charger
IN THE BOX
Solar Panel ×1
Universal Joint ×1
Circular Socket Nut ×1
Locking Screw Cap ×1
Base ×1
Screws ×3
Wall Anchors ×3
Quick Start Guide ×1
INSTALLATION
Place Solar Panel in an area with consistent sunlight throughout the year.lt only needs a few hours of direct sunlight each day to keep your camera powered.
The amount of energy that the solar panel produces is affected by weather conditions,seasonal changes, geographic location,etc.
-
Fix the base to your mounting location using the included screws. If the installation surface is soft or unstable,first use a 6.0 drill bit to drill a hole in the wall.then insert the anchor nail into the hole,and fix the base with screws.
-
First,install the locking screw cap into the universal joint and then screw the circular socket nut into the universal joint.
-
Screw the universaliointinto the back of the solar panel.Tighten it firmly with the attached nut.
-
Screw the locking screw cap into the base.Make sure that the universaljoint is angled upward.
-
When adjusting the solar panel left or right,loosen the locking screw cap,turn the sleeve rod,and tighten the locking screw cap when the panelis in position.
-
Solar panel’s angle can be adjusted up and down up to 90°.
Tip: After the installation is complete,please check that all locking mechanisms are tightly secured.
HOW TO POSITION YOUR SOLAR PANEL
- Find the area that gets the most direct sunlight throughout the day
- Angle the solar panel upward 30°.
- Point it south if in the northen hemisphere and north if in the southern hemisphere.
IMPORTANT
- Wipe the face of the solar panel with a soft ,damp cloth regularly to clear any dust or debris.
- Be sure to update the firmware version of the camera to the latest version.
- When the weather is cloudy and rainy, the solar power wll weaken sugntly, wnicn will only affect the delayed use when it is just installed.
- It is recommended to be in direct sunlight for at least 3-4 hours, depending on your usage. You need to make sure that there are no obstacles that might cast shadows on your ring solar panels, such as extended roofs, trees,shrubs, etc.
FCC WARNING
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 ofthe FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,and
(2) This device must accept any interference received,including interference
that may cause undesired operation.
ISEDCRSSWARNING
This device compiles with ISEDC licence-exempt RSS standard (s).Operation is subject to the following two conditions:
(1) This device may not cause interference,and
(2) This device must accept any interference,including interference that may
cause undesired operation of the device.
IMPORTANT NOTES
- Please regularly check the product, damaged or malfunctioning electrical appliances cannot continue to be used.
- The power cord cannot be replaced, if the cord is damaged, this product should be discarded.
- Do not modify or repair this product. These actions may result in fire, electric shock, or other injury.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children should not play with the appliance.
- Cleaning and user maintenance shall not be made by children witho.
BASIC PARAMETERS
Cable length:4m
Operating voltage:DC 5V OR 6V (For details, please refer to the parameters
behind the solar panel.)
Operating temperature:-20.5C to 48.5C ( -5F to 120F° )
Information for EU representatives
Name: Bright star consulting e.K.
Address: Humboldtstr.5, 31812 Bad Pyrmont Germany
E-mail: utaundnico@hotmail.com
UK representative information
Name: AOCE LIMITED
Address: Office Suite 29a 3/F 23 Wharf Street，London，England，SE
E-mail: aoce-service@outlook.com
Manufacturer: Shenzhen BinSheng Technology Development Co.,Ltd
4th Floor B Building ShuangJinhui Industrial Area Fuyong Street Baoan District
Shenzhen China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>