Smart Things sCharge s48 C Flush Mounted Power Supply 20 W Instruction Manual
- June 2, 2024
- Smart Things
Table of Contents
Smart Things sCharge s48 C Flush Mounted Power Supply 20 W
Product Information
Specifications:
- Input Voltage: 100 – 250 V~ 50/60 Hz
- Input Current: Max. 1.5 A
- Output:
- USB 5 V, 3 A max.
- USB 9V, 2.22 A max.
- Output Power: 20 Watt max
- Power Loss (Standby Consumption): 50 mW
Product Usage Instructions
Installation:
Note: Only to be installed by persons with relevant electrical
qualifications and experience. Improper installation can lead to serious risks
and damages. Contact a qualified electrical engineer for installation.
Maintenance and Cleaning:
- This USB charger is maintenance-free.
- Repairs should only be carried out by a qualified electrician.
- Clean the unit with a soft, clean, dry, lint-free cloth only. Do not use solvent-based cleaning agents.
- Do not use wet cloths or sponges to clean the socket outlet.
FAQ
Can I use this charger with devices that require more than 20W?
The charger has an output of 20W max. It is recommended not to use it with devices that require more power to avoid damage.
What should I do if the charger is not working?
Check the power source, cable connections, and try using a different outlet. If the issue persists, contact customer support for assistance.
Function
This flush-mountable single-port USB charger charges the batteries of mobile
devices. The USB charger is ideally suited for charging tablets that are
installed on the wall, using commercially available wall mounts. The maximum
permissible voltage is 250V~ 50/60Hz. 16A.
Only install and use this IP20-protected product in protected locations with
an ambient temperature between 5ºC and 35ºC. Avoid the influence of moisture,
dust, sun or other heat radiation. For prolonged use, the housing of this
product may become warm. This is normal.
HAZARD WARNINGS
- Operate this device only in indoor areas. Avoid the influence of moisture, dust, sun or other heat radiation.
- This USB charger is part of the building installation.
- The relevant standards and directives of the country must be observed during planning and construction.
- The operation of the device is permissible only on the 230V / 50 Hz alternating current network.
- Work on the 230V mains may only be carried out by a certified electrician qualified in your country.
- The applicable accident prevention regulations must be observed.
- To avoid an electric shock on the device, please disconnect the mains voltage to the device (switch off the circuit breaker).
- Failure to comply with the installation instructions may cause fire or other hazards.
- The installation may only be carried out in commercially available flush-mounted wall boxes (installation boxes), with a minimum depth of 40mm.
- When connecting the device terminals, observe the type of cabling which are permissible for this purpose.
- Pay close attention to the wiring diagram!
Mandatory information by the equipment safety standard:
Note! Only to be installed by persons with relevant electrical
qualifications and experience!*)
Improper installation will result in risk to your own life and risk to the
life of persons using the electrical installation. With an improper
installation, you risk serious material damages, for example fire. You are
personnaly reliable for personal injury and material damages. Please contact a
qualified electrical engineer.
INSTALLATION
Specialist skills required for installation
In particular, the following special knowledge is required for the
installation:
- The applicable“5 Safety Rules”: disconnect; protect against switching on; verifying mains power disconnect; earthing and short-circuiting; covering adjacent current-carrying components or making them inaccessible.
- Selection of suitable tools, measuring equipment and – if necessary – personal protection equipment;
- Evaluation of measurement results;
- Selection of the electrical installation material to ensure compliance with the shut-down conditions;
- IP-Protection classes;
- Installation of electrical installation material;
- the resulting connection conditions (conventional protective multiple earthing, safety earthing, additional measures required etc.).
Maintenance and cleaning
This USB charger is maintenance-free. Any repairs should only be carried out by a qualified electrician. Clean the unit with a soft, clean, dry, lint-free cloth only. Please do not use solvent-based cleaning agents. The plastic housing could be affected by this. Do not use wet cloths or sponges to clean the socket outlet.
RoHS/WEEE Compliance Statement (Recycling Instructions)
European Directive 2012/19/EU requires that equipment bearing the trashcan
symbol on the product and/or its packaging must not be disposed of with
unsorted municipal waste. The symbol indicates that this product should be
disposed of separately from regular household waste streams. It is your
responsibility to dispose of this via designated collection facilities
appointed by the government or local authorities. Correct disposal and
recycling will help prevent potential negative consequences to the environment
and human health. For more detailed information about the disposal of your old
equipment, please contact your local authorities, waste disposal service, or
the shop where you purchased the product.
Technical Specifications
- Input voltage 100 – 250 V~ 50/60 Hz
- Input current Max. 1,5 A
- Output:
- USB 5 V⎓, 3 A max.
- USB 9V ⎓, 2,22 A max.
- Output power 20Watt max
- Power loss (Standby consumption) ≤50 mW
sCharge 20W USB power supply
- Type: JP – 3503 UP-ST
- Input: 100 – 250 V~ / 50 – 60 Hz,
- Output:
- USB 5 V⎓, 3 A max.
- USB 9V ⎓, 2,22 A max.
Documentation
© Smart Things, Germany. All rights reserved. We accept no liability for
technical or printing errors and their consequences. All trademarks and
property rights are acknowledged. Changes in the sense of technical progress
may be made without prior notice.
Smart Things Solutions GmbH
Grubmühlerfeldstr. 54
82131 Gauting, GERMANY
info@smart-things.com
www.smart-things.com
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>