GARDENA 14772 Battery Pruning Lopper Battery Instruction Manual

: June 2, 2024
: Gardena

Table of Contents

GARDENA 14772 Battery Pruning Lopper Battery
Product liability
SAFETY WARNINGS
ASSEMBLY
OPERATION
MAINTENANCE
STORAGE
TROUBLESHOOTING
TECHNICAL DATA
ACCESSORIES / SPARE PARTS
SERVICE
EC Declaration of Conformity
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

GARDENA 14772 Battery Pruning Lopper Battery

GARDENA-14772-Battery-Pruning-Lopper-Battery-PRODUCT

Product liability

By the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from our products where said products have not been properly repaired by a GARDENA-approved service partner or where original GARDENA parts or parts authorized by GARDENA were not used.

SAFETY WARNINGS

Explanation of the symbols:

General safety warnings General machine safety warnings

Read all safety warnings, instructions, illustrations, and specifications provided by this machine.
Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
The term “machine” in the warnings refers to your mains-operated (corded) machine or battery-operated (cordless) machine.

Work area safety
- a) Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
- b) Do not operate machines in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
- Machines create sparks which may ignite the dust or fumes.
- c) Keep children and bystanders away while operating a machine.
- Distractions can cause you to lose control.
Electrical safety
- a) Machine plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) machines.
- Unmodified plugs and matching outlets will reduce the risk of electric shock.
- b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- c) Do not expose machines to rain or wet conditions.
- Water entering a machine will increase the risk of electric shock.
- d) Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the machine. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
- e) When operating a machine outdoors, use an extension cord suitable for outdoor use.
- The use of a cord suitable for outdoor use reduces the risk of electric shock.
- f) If operating a machine in a damp location is unavoidable, use a residual current device (RCD) protected supply.
- The use of an RCD reduces the risk of electric shock.
Personal safety
- a) Stay alert, watch what you are doing, and use common sense when operating a machine. Do not use a machine while you are tired or under the influence of drugs, alcohol, or medication.
- A moment of inattention while operating machines may result in serious personal injury.
- b) Use personal protective equipment. Always wear eye protection.
- Protective equipment such as a dust mask, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
- c) Prevent unintentional starting. Ensure the switch is in the OFF position before connecting to the power source and/or battery pack, picking up or carrying the machine.
- Carrying machines with your finger on the switch or energizing machines that have the switch on invites accidents.
- d) Remove any adjusting key or wrench before turning the machine on.
- A wrench or a key left attached to a rotating part of the machine may result in personal injury.
- e) Do not overreach. Keep proper footing and balance at all times.
- This enables better control of the machine in unexpected situations.
- f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts.
- Loose clothes, jewelry, or long hair can be caught in moving parts.
- g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
- The use of dust collection can reduce dust-related hazards.
- h) Do not let familiarity gained from frequent use of machines allow you to become complacent and ignore machine safety principles.
- A careless action can cause severe injury within a fraction of a second.
Machine use and care
- a) Do not force the machine. Use the correct machine for your application.
- The correct machine will do the job better and safer at the rate for which it was designed.
- b) Do not use the machine if the switch does not turn it on and off.
- Any machine that cannot be controlled with the switch is dangerous and must be repaired.
- c) Disconnect the plug from the power source and/or the battery pack from the machine before making any adjustments, changing accessories, or storing machines. Such preventive safety measures reduce the risk of starting the machine accidentally.
- d) Store idle machines out of the reach of children and do not allow persons unfamiliar with the machine or these instructions to operate the machine. Machines are dangerous in the hands of untrained users.
- e) Maintain machines. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the machine’s operation.
- If damaged, have the machine repaired before use. Many accidents are caused by poorly maintained machines.
- f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- g) Use the machine, accessories tool bits, etc. under these instructions, taking into account the working conditions and the work to be performed. Use of the machine for operations different from those intended could result in a hazardous situation.
- h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the machine in unexpected situations.
Battery tool use and care
- a) Recharge only with the charger specified by the manufacturer.
- A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- b) Use machines only with specifically designated battery packs.
- Use of any other battery packs may create a risk of injury and fire.
- c) When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another.
- Shorting the battery terminals together may cause burns or a fire.
- d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water.
- If liquid contacts the eyes, additionally seek medical help.
- Liquid ejected from the battery may cause irritation or burns.
- e) Do not use a battery pack or tool that is damaged or modified.
- Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
- f) Do not expose a battery pack or tool to fire or excessive temperature.
- Exposure to fire or temperature above 130 °C may cause an explosion.
- g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions.
- Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
Service
- a) Have your machine serviced by a qualified repair person using only identical replacement parts.
- This will ensure that the safety of the machine is maintained.
- b) Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
- National regulation can restrict the use of the lopper.
- Daily inspection before use and after dropping or other impacts to identify any significant damage or defects.

Lopper safety warnings:

a) Keep all parts of the body away from the blade. Do not remove cut material or hold material to be cut when the blade is moving. Blades continue to move after the switch is turned off.
A moment of inattention while operating the lopper may result in serious personal injury.
b) Carry the lopper by the handle with the blade stopped and take care not to operate any power switch. Proper carrying of the lopper will decrease the risk of inadvertent starting and resultant personal injury from the blades.
c) When transporting or storing the lopper, always fit the blade cover.
Proper handling of the lopper will decrease the risk of personal injury from the blades.
d) When clearing jammed material or servicing the unit, make sure all power switches are off and the battery pack is removed or disconnected.
Unexpected actuation of the lopper while clearing jammed material or servicing may result in serious personal injury.
e) When clearing jammed material or servicing the unit, make sure all power switches are off and the lock-off is in the locked position. Unexpected actuation of the lopper while clearing jammed material or servicing may result in serious personal injury.
f) Hold the lopper by insulated gripping surfaces only, because the blade may contact hidden wiring.
Blades contacting a “live” wire may make exposed metal parts of the lopper “live” and could give the operator an electric shock.
g) Keep all power cords and cables away from the cutting area.
Power cords or cables may be hidden in hedges or bushes and can be accidentally cut by the blade.
h) Do not use the lopper in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning.

Extended-reach lopper safety warnings:

a) To reduce the risk of electrocution, never use the extended-reach lop-per near any electrical power lines. Contact with or use near power lines may cause serious injury or electric shock resulting in death.
b ) Always use two hands when operating the extended-reach lopper. Hold the extended-reach lopper with both hands to avoid loss of control.
c ) Always use head protection when operating the extended-reach lopper overhead. Falling debris can result in serious personal injury.
Search hedges and bushes for hidden objects (e.g. wire fences and hidden wires).
Use a residual current device (RCD) with a trip current of 30 mA or less.
Hold the lopper with both hands on both handles.
When in use, stand on the floor and not on a ladder or other unstable surface.
Before using the lopper, make sure that the locking devices of all moving parts (e.g. the extended shaft and the pivot element) are in the locked position.

Additional safety warnings

Intended use:

The GARDENA Lopper is intended for delimbing trees, hedges, shrubs, and bushes with limbs of up to 28 mm in diameter in private domestic gardens or allotments.
The product is not intended for long-term use (professional use).

DANGER Risk of physical injury!

Cut branches into parts to ensure that you cannot be struck by falling branches or that fallen branches can bounce up from the soil.
Do not stand under the branch while cutting.
Do not use it for pond care.

Safety warnings for batteries and chargers

Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock, fire, and/or serious injury.
Store these instructions in a safe place. Only use the charger if you can fully evaluate all functions and carry them out without restrictions, or if you have received corresponding instructions.
Supervise children during use, cleaning, and maintenance.
This will ensure that children do not play with the charger.
Charge only lithium-ion batteries of the POWER FOR ALL system type PBA 18V with a capacity of 1.5 Ah or more (5 battery cells or more).
The battery voltage must match the battery charging voltage of the charger. Do not charge any non-rechargeable batteries.
Otherwise, there is a risk of fire and explosion.
Do not expose the charger to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Keep the charger clean. Dirt poses a risk of electric shock.
Always check the charger, cable, and plug before use. Stop using the charger if you discover any damage.
Do not open the charger yourself, and have it repaired only by a qualified specialist using only original replacement parts.
Damaged chargers, cables, and plugs increase the risk of electric shock.
Do not operate the charger on an easily ignited surface (e. g. paper, textiles, etc.) or in a flammable environment.
There is a risk of fire due to the charger heating up during operation.
To avoid safety hazards, if the power supply cord needs to be replaced, this must be done by GARDENA or by a customer service center that is authorized to repair GARDENA power tools.
Do not operate the product while it is charging.
Products sold in GB only: Your product is fitted with a BS 1363/A approved electric plug with an internal fuse (ASTA approved to BS 1362). If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in their place by an authorized customer service agent. The replacement plug should have the same fuse rating as the original plug. The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a main socket elsewhere.
These safety warnings apply only for 18V Li-ion rechargeable batteries for the POWER FOR ALL system.
Use the rechargeable battery only with products from POWER FOR
ALL System partners. 18V rechargeable batteries labeled with POWER FOR
ALL are fully compatible with the following products: All 18 V products from POWER FOR ALL System partners.
Observe the battery recommendations in the operating manual of your product.
Only this way can the rechargeable battery and the product be operated without danger and the rechargeable batteries protected from hazardous overloading.
Only charge the batteries using chargers recommended by the manufacturer or by POWER FOR ALL system partners. A charger that is suitable for one type of battery pack may pose a fire risk when used with different batteries (Battery type: PBA 18V… / compatible chargers: AL 18…).
The battery is supplied partially charged.
To ensure full battery capacity, fully charge the battery in the charger before using your power tool for the first time.
Keep battery packs out of the reach of children.
Do not open the battery. There is a risk of short-circuiting.
In case of damage and improper use of the battery, vapors may be emitted. The battery can set alight or explode.
Ensure the area is well-ventilated and seek medical attention should you experience any adverse effects. The vapors may irritate the respiratory system.
If used incorrectly or if the battery is damaged, flammable liquid may be ejected from the battery. Contact with this liquid should be avoided. If contact accidentally occurs, rinse off with water. If the liquid comes into contact with your eyes, seek additional medical attention.
Liquid ejected from the battery may cause irritation or burns.
If the battery is damaged liquid can be ejected and cover nearby surfaces.
Check affected parts. Clean these parts or change them if necessary.
Do not short-circuit the battery pack. When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
The battery contacts can be hot after use. Be careful of the hot contacts when removing the battery.
The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode, or overheat.
Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
Protect the battery against heat, e.g. continuous intense sunlight, fire, dirt, water, and moisture.
There is a risk of explosion and short-circuiting.
Only operate and store the battery at an ambient temperature between – 20 °C and + 50 °C.
Do not leave the battery in your car in the summer, for example.
At temperatures of < 0 °C some devices may experience a loss of power.
Only charge the battery at an ambient temperature which is between 0 °C and + 35 °C. Only charge the rechargeable battery with a USB cable at an ambient temperature which is between + 10 °C and + 35 °C.
Charging outside of this temperature range can increase the risk of damage to the battery and pose a fire hazard.
After use, allow the battery to cool down for at least 30 minutes before charging or storing.

Additional electrical safety warnings

DANGER Cardiac arrest!

This product makes an electromagnetic field while it operates. This field may under some conditions interfere with active or passive medical implants.
To decrease the risk of conditions that can injure or kill, we recommend persons with medical implants speak with their physician and the medical implant manufacturer before they operate the product.
Do not use or store damaged batteries. Immediately dispose of the defective battery correctly.
Only connect the charger to the AC voltage specified on the rating plate.
Do not connect an earth wire to the product.
Do not use the product when a thunderstorm is approaching.
Protect the battery contacts from moisture.

Additional Personal Safety Warnings

DANGER Risk of suffocation!

Small parts can be easily swallowed. There is also a risk that the polybag can suffocate toddlers.
Keep toddlers away when you assemble the product.
Do not overload the product (Use according to the user manual).
Do not use close to water.
Only use the lopper in the manner and for the functions described in these instructions.
The operator or user is responsible for accidents or hazards occurring to other people or their property.
Pay special attention to the hazard for third parties posed by the increased working radius when the telescopic tube is extended.
Always wear suitable clothing, gloves, and stout shoes.
Check the areas where the lopper is to be used and remove any wires, hidden electrical cables, and other foreign objects.
Put the protective cover on for all adjustment work (tilting the cutting head, changing the telescopic tube length)
Do not put the lopper on the cutting head.
Check the machine before using and after any impact for signs of wear or damage
Let the appropriate repair work be carried out if necessary.
Do not attempt to use an incomplete product or one with an unauthorized modification.

Power tool use and care

Know how to stop the product quickly in an emergency.
Do not hold the product by the protective cover.
Do not use the lopper if the protection equipment is damaged.
Do not use ladders whilst operating the lopper.
Always use the lopper when standing on solid ground.
Remove the battery:
before leaving the lopper unattended for any period;
before clearing a blockage;
before checking, cleaning, or working on the lopper;
if you hit an object. Do not use your lopper until you are sure that the entire lopper is in a safe operating condition;
if the lopper starts to vibrate abnormally. Check immediately.
Excessive vibration can cause injury.
before passing to another person.
All nuts and screws must be firmly tightened to ensure the safe operating condition of the product.
Let the lopper cool down before storage If the lopper gets hot during operation.
Do not store the lopper over 35 °C or under direct exposure to sunlight.
Do not store the lopper in places with static electricity.
Beware of falling debris.
Only work in the daylight or when visibility is good.

ASSEMBLY

DANGER Cutting injury due to the blade!

Risk of cut injury due to accidental starting.
Use gloves.
Remove the battery.
Slide the protective cover over the blade.

To assemble the lopper [ Fig. A1 / A2 ]:

Without extension tube (only for Art. 14774):

Slide the cutting head (3) into the handle unit (2) until it stops.
- Thereby the nose (N) must be slid into the opening (O).
Tighten the nut (4).

With extension tube (only for Art. 14776):

DANGER Personal injury!

Only 1 extension tube may be used.
Only use one extension tube.
Slide the extension tube (1) into the handle unit (2) until it stops.
Thereby the nose (N) must be slid into the opening (O).
Tighten the nut ß4a.
Slide the cutting head (3) into the telescopic tube (1) until it stops.
Thereby the nose (N) must be slid into the opening (O).
Tighten the nut (4).

To assemble the branch hook (only for Art. 14774 / 14776) [ Fig. A3 ]:

The branch hook is used for easy removal of cut branches from the tree crown and shrub.

To assemble the branch hook:

Slide the branch hook (5) until it stops into the holder (6) on the cutting head (3) until the lock (7) audibly engages.
Make sure that the lock is engaged.

To disassemble the branch hook:

First, pull the lock (7) upwards.
Then pull the branch hook (5) out of the holder (6) on the cutting head (3).

OPERATION

DANGER Cutting injury due to the blade!

Risk of cut injury due to accidental starting.
Use gloves.
Remove the battery.
Slide the protective cover over the blade.

To charge the battery [ Fig. O1 / O2 / O3 ]:

CAUTION!

The voltage of the power source must match the voltage specified on the rating plate of the charger.
v Note the mains voltage.
For the GARDENA Battery Loppers Art. 14772-55 / 14774-55 / 14776-55 there is no battery and no charger in the scope of delivery.
Thanks to the intelligent charging process, the charge condition of the battery is automatically detected and then charged up with the optimal charge current depending on battery temperature and voltage.
In this way, the battery is treated with care and remains permanently fully charged when it is stored in the charger.

Push the locking button (A) and remove the battery (B) from the battery holder (D).
Connect the battery charger (C) into a mains socket.
Slide the battery charger (C) onto the battery (B).
- When the battery charge indicator (Lc) at the charger blinks green the battery is being charged.
- When the battery charge indicator (Lc) at the charger lights permanently green the battery is completely charged (Charging time, see 7. TECHNICAL DATA).
Examine the charge status regularly while you charge.
When the battery (B) is completely charged, the battery (B) can be disconnected from the charger (C).

Meaning of the indication elements Indication on the charger

Flashing of the Battery Charge Indicator (Lc)
- The charging procedure is indicated by flashing of the battery charge indicator (Lc).
- Note: The charging procedure is only possible when the battery temperature is within the allowable charging temperature range, see 7. TECHNICAL DATA.
Continuous Lighting of the Battery Charge Indicator (Lc)
- Continuous lighting of the battery charge indicator (Lc) indicates that the battery is fully charged or that the temperature of the battery is not within the allowable charging temperature range and can therefore not be charged.
- When the battery is not inserted, continuous lighting of the battery charge indicator (Lc) indicates that the mains plug is inserted in the socket outlet and that the battery charger is ready for operation.

Battery charge status indication (P) on the product [ Fig. O4 / O1 ]:

After starting the product, the battery charge status indication (P) is displayed for 5 seconds.
If the LED (L1) blinks green, the battery must be charged.
If the error LED (Wp) is lighting or blinking see 6. TROUBLESHOOTING.

Working position [ Fig. O5 ]:

Hold the lopper with one hand on the upper gripping surface (U) and with the other hand on the handle (H).

To extend the telescopic tube (only for Art. 14774 / 14776) [ Fig. O6 ]:

The telescopic tube (2) can be continuously extended by up to 40 cm.

DANGER Personal injury!

When extending the telescopic tube, the hand can be trapped between the clamping sleeve and the orange nut if the lopper is held upwards while doing so.
Hold the lopper horizontally when extending the telescopic tube.

Loosen the orange nut (12).
Extend the telescopic tube (2) to the desired length.
Tighten the orange nut (12) again.

To tilt the cutting head [ Fig. O7 ]:

The cutting head (3) can be tilted in 20° increments from 0° to 60° in 4 positions.

Push the elbow joint (13) and adjust the cutting head (3) to the desired angle.
Let the cutting head (3) engage at the desired angle.

Make sure that the cutting head is engaged

To start the lopper [ Fig. O1 ]:

DANGER! Risk of physical injury!
Risk of injury if the product does not stop when the start lever is released.
Do not bypass the safety devices or switches.
For example, do not attach the start lever to the handle.

To start the lopper:

The product is provided with a double safety device (start lever and safety interlock) to prevent the product from being turned on by accident.

Put the battery (B) into the battery holder (D) until it audibly engages.
Open the snap-fit (14) of the protective cover and remove it from the blade.
Hold the lopper with one hand on the upper gripping surface (U) and with the other hand on the handle (H).
Slide the safety interlock (10) forward and pull briefly the start lever (11) towards the handle (H).
- The blade closes and opens for initialization.
- The lopper is now ready for operation.
Slide the safety interlock (10) forward and pull the start lever (11) towards the handle (H).
- The lopper closes and remains closed until the start lever is released.
- The battery charge level indicator (P) is displayed for 5 seconds.
Release the safety interlock (10).

Sleep-Timer-Funktion:

If the lopper has not been used for 15 minutes, the lopper switches off.
After that, the start lever must be pulled briefly towards the handle again for re-initialization.

To transport the lopper:

Release the start lever (11).
- The lopper stops.
Remove the battery.
Slide the protective cover over the blade.

MAINTENANCE

DANGER Cutting injury due to the blade!

Risk of cut injury due to accidental starting.
Use gloves.
Remove the battery.
Slide the protective cover over the blade.

To clean the lopper:

DANGER Risk of physical injury!

Risk of injury and risk of damage to the product.
Do not clean the product with water or with a water jet (in particular high-pressure water jet).
Do not clean with chemicals including petrol or solvents. Some can destroy critical plastic parts.
The airflow slots must always be clean.

Clean the lopper with a damp cloth.
Clean the airflow slots with a soft brush (do not use sharp objects).
Clean the cutting head with a brush, if necessary.

To clean the battery and the battery charger:

The surface and the contacts of the battery and the battery charger must be clean and dry before the battery is connected to the battery charger.
Do not use running water.

To clean the battery:

No chemical substances may be used for cleaning the battery.
Occasionally clean the ventilation slots and the terminals on the battery with a soft, clean, and dry brush.

To clean the battery charger:

Clean the contacts and the plastic parts with a soft and dry cloth.

STORAGE

To put into storage:

The product must be stored away from children.

Remove the battery.
Slide the protective cover over the blade.
Charge the battery.
Clean the lopper, the battery, and the battery charger (see 4. MAINTENANCE).
Store the lopper, the battery, and the battery charger in a dry, enclosed, and frost-free place.

TROUBLESHOOTING

DANGER Cutting injury due to the blade!

Risk of cut injury due to accidental starting.
Use gloves.
Remove the battery.
Slide the protective cover over the blade.

Troubleshooting table:

NOTE: Repairs must only be done by the GARDENA service departments or specialist dealers approved by GARDENA.
For any other malfunctions please contact the GARDENA service department.

TECHNICAL DATA

Lopper| Unit| Value (Art. 14772)| Value (Art. 14774)| Value (Art. 14776)
---|---|---|---|---
Max. branch diameter| mm| 28| 28| 28
Max. cuts per battery charge

PBA 18V 2.0Ah W-B 400

| 400| 400
PBA 18V 2.5Ah W-B| 500| 500| 500
PBA 18V 3.0Ah W-B| 600| 600| 600
PBA 18V 4.0Ah W-C| 800| 800| 800
PBA 18V 5.0Ah W-C| 1000| 1000| 1000
PBA 18V 6.0Ah W-C| 1200| 1200| 1200
Range of extension of cm                     –| 215 – 255| 320 – 360
Max. Height (with telescopic cm                 110| 255| 360
Weight (without Battery) kg                      1.9| 3.4| 4.1
Sound pressure level L 1) 65| 63| 57
pA dB (A) Uncertainty k pA 3| 3| 3
Sound power level L W 2) : A measured/guaranteed 76 / 79|

77 / 80

|

77 / 80

Uncertainty k dB (A) 3| 3| 3
Hand/arm vibration a vhw m/s2 ≤ 2.5

1)

| ≤ 2.5| ≤ 2.5
Uncertainty know **** 1.5| 1.5| 1.5

Measuring process complying with: 1) EN IEC 62841-4-2 2) RL 2000/14/EC / S.I. 2001/1701
NOTE: The stated vibration emission value has been measured according to a standardized test procedure and can be used for comparison of one electric power tool with another.
It can also be used for preliminary evaluation of exposure. The vibration emission value can vary during the actual use of the electric power tool depending on how the machine is used.
As a safety measure, you should work with the machine for a maximum of 1 hour without interruption.

ACCESSORIES / SPARE PARTS

GARDENA-14772-Battery-Pruning-Lopper-Battery-FIG-22

SERVICE

Please contact the address on the enclosed warranty card.

DISPOSAL

Disposal of the lopper: (according to Directive 2012/19/EU / S.I. 2013 No. 3113)
The product must not be disposed of as normal household waste. It must be disposed of in line with local environmental regulations.

IMPORTANT!

Dispose of the product through or via your local recycling collection center.

Disposal of the battery:

The battery contains lithium-ion cells that should not be disposed of with normal household waste at the end of its life.

IMPORTANT!

Discharge the lithium-ion cells completely (contact the GARDENA Service).
Protect the contacts on the lithium-ion cells against short circuits.
Dispose of the lithium-ion cells properly via or through your local recycling collection center.

EC Declaration of Conformity

The undersigned hereby certifies as the authorized representative of the manufacturer, GARDENA Germany AB, PO Box 7454, S-103 92, Stockholm, Sweden, that, when leaving our factory, the unit(s) indicated below is/are under the harmonized EU guidelines, EU standards of safety and product specific standards. This certificate becomes void if the unit(s) is/are modified without our approval.
Description of the product: Battery Pruning Lopper / Battery Telescopic Pruning Lopper
Product type:
Article number:
EasyCut 110/18V P4A
HighCut 250/18V P4A
HighCut 360/18V P4A
14772
14774
14776
EC-Directives: 2006/42/EG
- 2000/14/EG
- 2014/30/EU
- 2011/65/EU
Charger: 2014/35/EU
Noise level measured/guaranteed
- Art. 14772: 76 dB(A) / 79 dB(A)
- Art. 14774: 77 dB(A) / 80 dB(A)
- Art. 14776: 77 dB(A) / 80 dB(A)
Year of CE marking: 2022

UKCA Declaration of Conformity The manufacturer: GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Sweden hereby certifies, when leaving our factory, the unit(s) indicated below is/are by the UK Regulations, designated standards of safety and product-specific designated standards. This certificate becomes void if the units are modified without our approval.

Description of the product:| Battery Pruning Lopper / Battery Telescopic Pruning Lopper
Product type:| EasyCut 110/18V P4A HighCut 250/18V P4A HighCut 360/18V P4A
Article number:| 14772

14774

14776

Art. 14774:

Art. 14776:

| 76 dB(A) / 79 dB(A)

77 dB(A) / 80 dB(A)

Deutschland / Germany

GARDENA Manufacturing GmbH
Central Service
Hans-Lorenser-Straße 40 D-89079 Ulm
Produktfragen: (+49) 731 490-123
Reparaturen: (+49) 731 490-290
service@gardena.com
http://www.gardena.com

UAE

Al-Futtaim ACE Company
L.L.C Building, Al Rebat Street
Festival City, Dubai
7880 UAE
Phone: (+971) 4 206 6700
ace@alfuttaim.ae

Netherlands

Husqvarna Nederland B.V.
GARDENA Division
Postbus 50131
1305 AC ALMERE
Phone: (+31) 36 521 00 10
info@gardena.nl

Documents / Resources

| GARDENA 14772 Battery Pruning Lopper Battery [pdf] Instruction Manual
14772 Battery Pruning Lopper Battery, 14772, Battery Pruning Lopper Battery, Pruning Lopper Battery, Lopper Battery, Battery
---|---