SB1860 Sound Blaster Play 4 Instructions
- June 7, 2024
- Sound Blaster
Table of Contents
SB1860 Sound Blaster Play 4 Instructions
Safety & Regulatory Information
Read this instruction carefully and completely before using the product. Refer to the following information to use your product safely, and to reduce the chance of electric shock, short-circuiting, damage, fire, hearing impairment or other hazards. Improper handling may void the warranty for your product. For more information, read the warranty available with your product.
- Always keep the product dry and do not expose it to extreme temperatures (hairdryer, heater, extended exposure to sunlight, etc.) to avoid corrosion or deformation.
- Do not expose your product to water and moisture. If your product is moisture-resistant, take care and not to immerse in water or expose to rain.
- Clean the product only with a soft, dry cloth.
- Do not dismantle or attempt to repair your product.
- Do not pierce, crush or set fire to your product
- Keep your product away from strong magnetic objects
- Keep the product, accessories and packaging parts out of reach of children and pets to prevent accidents. Swallowing and choking hazard.
Warning on Choking Hazard
This product and its accessories may contain small parts which must be kept
away from children.
WARNING: CHOKING HAZARD – Small Parts Not for children under 3yrs. The following sections contain notices for various countries
CAUTION:
This product is intended for use with FCC/CE certified computer equipment.
Please check the equipment operating/installation manual and/or with the
equipment manufacturer to verify/confirm if your equipment is suitable prior
to the installation or use of the product.
Notice for USA
Federal Communication Commission (FCC) Interference Statement
FCC Part 15: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if no installed and used in accordance
with instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subjected to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be installed with computer equipment certified to comply with Class B limits. All cables used to connect to the computer and peripherals must be shielded and grounded. Operation with non-certified computers or non-shielded cables may result in interference to radio or television reception.
MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.
SUPPLIER’S DECLARATION OF CONFORMITY According to CFR Title 47 §2.1077
Importer’s Name: Creative Labs, Inc.
Importer’s Address: 1901 McCarthy Boulevard Milpitas, CA. 95035 Tel:
(408)428-6600
declares under its sole responsibility that the product
Trade Name: Creative
Model Numbers: SB1860
Product Name: Sound Blaster Play! 4C
has been tested according to the FCC / CISPR22 requirement for Class B devices and found compliant with the following standards:
EMI/EMC: ANSI C63.4, FCC Part 15 Subpart B Complies with Canadian ICES-003 Class B
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesirable operation.
Supplementary Information : Thinh Bui Compliance Manager Creative Labs, Inc. 1st Dec 2020
European Compliance
This product complies with all applicable directives. A copy of the EU DoC is available at Creative website.
CAUTION: To comply with the Europe CE requirement, this device must be
installed with CE certified computer equipment which meet with Class B limits.
All cables used to connect this device must be shielded, grounded and no
longer than 3m in length. Operation with non-certified computers or incorrect
cables may result in interference to other devices or undesired effects to the
product.
MODIFICATION: Any changes or modifications not expressly approved by Creative Technology Limited or one of its affiliated companies could void the user’s warranty and guarantee rights. The insulating coating on the device also serves the purpose of ESD protection.
Notice for Japan
Vietnam RoHS Statement
This product is in compliance with Circular 30/2011/TTBCT of the Ministry of
Trade of the Socialist Republic of Vietnam (“Circular”), it does not contain
the following substances in concentration greater than the Maximum Limit value
as specified in the Circular.
Substance
|
Maximum Limit (ppm)1, 2
---|---
lead
|
1000
mercury
|
1000
cadmium
|
100
hexavalent chromium
|
1000
polybrominated biphenyls (PBB)
|
1000
polybrominated biphenyl ethers (PBDE)
|
1000
- Maximum Limit does not apply to applications exempted from the Circular.
- Maximum Limit refers to concentration by weight in homogeneous materials.