Xiangcheng 2A2UU-A1 A1 80mm Receipt Printer

Product Specifications

• Print Way : Direct line heat sensitivity
• Print Speed : 220 mm/s
• Print Width : 72 mm
• Print Command : Bitmap, ESC/POS commands
• Interface Type : Type-C + Netport + DC + DK
• Cutting Mechanism : Half-cut automatic paper-cutting knife
• Connectivity : BT + USB + WIFI + Netport
• Adapter Input Voltage : 100-240V~, 50/60Hz, 1.5A
• Adapter Output Voltage : 24V/2.5A
• Printer Input Voltage : 24V/2.5A
• Operating Environment: 0-40°C
• Storage Environment: -30-70°C
• Dimensions: 127127126 mm

Product Usage Instructions

Printer Unpacking:

1. User’s Guide * 1
2. Printer Main Body * 1
3. Power Line * 1
4. Power Adapter * 1

Printer Connector:

Type-C 1, RJ45 1, DC 1, DK1

Installing Roll Paper:

1. Pull the side lever to open the top hatch
2. Follow the picture directions for paper orientation
3. Pull out some paper and close the top hatch
4. Check for paper alignment

Keys and Indicator Lights:

1. Green Light : Printer standby
2. Marquee Light : Printer powering on
3. Blinking Red Lamp : Printer overheating, stop printing
4. Red and Blue Flashing : Printer cover open/out of paper
5. FEED Key : Press for paper feed, press continuously for continuous feed

Buzzer Alarm:

Buzzer alerts for paper absence, overheating, open cover, etc.

Cut Knife Maintenance:

Open the cover lever and move it 10 times consecutively to resolve cut knife issues. Do not force open to avoid damage.

FAQ

• Can I use this printer without a power adapter?
  • No, the printer requires the power adapter for operation.
• What should I do if the printer shows a red and blue flashing light?
  • The red and blue flashing light indicates that the printer cover is open or out of paper. Close the cover securely or refill the paper.
• How do I know if the printer is overheating?
  • If the red light is blinking, it means the printer is overheating. Stop printing and allow the printer to cool down before resuming.

A. Matters need attention

1. The printer should be installed in a stable place to avoid placing the printer in a place with vibration and shock
2. Connect the printer’s power adapter to a suitable ground socket. Avoid using the same socket with other large motor equipment that can cause power supply voltage fluctuation.
3. Avoid gray cargo conductive substances into the printer interior, once happened, should immediately cut off the power supply
4. The printer avoids printing in the paperless state, otherwise it will seriously damage the printing roller and thermal printing head
5. If not for a long time, disconnect the printer power adapter
6. Users shall not disassemble the printer for maintenance or modification without authorization
7. Power adapters use only the random and exclusive power adapters
8. In order to ensure the printing quality and the life of products, it is recommended to use high quality printing paper
9. Please keep this manual properly for your reference

B. Printer unpacking：

1. user’s guide * 1
2. Printer main body * 1
3. power line * 1
4. Power adapter * 1

C. Technical parameter

• Print way: Direct line heat sensitivity
• print out rate : At 220 mm / s
• scroll : Width: 72 mm
• print command: Bitmap, ESC / POS commands
• interface type: Type-C + Netport + DC+DK
• Automatic paper cutting knife: Half cut
• Connect to the printer mode: BT+USB+WIFI+Netport
• Adapter voltage: 100-240V~,50/60Hz,1.5A
• input adapter voltage output: 24V/2.5A
• Printer input voltage: 24V/2.5A
• work environment: 0℃-40℃
• Storage environment: -30℃-70℃
• size: 127127126

Introduction to the printer connector

• Type-C *1
• RJ45 *1
• DC *1
• DK*1

Install roll paper

1. Pull the side lever, and the top hatch automatically bounces
2. Follow the direction of the picture, and pay attention to the direction of the paper
3. Pull out part of the paper outside the fuselage, press the top hatch cover, and the whole machine closes the lid
4. Check the paper position for deviation

Keys and indicator lights

1. Greenlight breathing: Printer’s bright green breath indicates printer standby.
2. Marquee: The printer light indicates that the printer is powered on.
3. Blinking red lamp : The red light flashing of the printer indicates that the printer movement is overheating, Stop printing.
4. Red and blue flashing : The red and blue printer light means the printer cover is open / out of paper.
5. FEED : Press this key to take the paper, if you continue to press this key, continuous paper delivery

Buzzer alarm: In the absence of paper, overheating, open cover, and other abnormal states after the buzzer alarm
Cut knife stuck maintenance : Open the cover lever to move 10 times consecutively， The blade can be opened after exiting
Warning : Do not force open the flap to damage the print head and automatic paper cutter.

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator& your body.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>