INPECO CAB2C13M01 Automation System User Manual

INPECO CAB2C13M01 Automation System

Product Information

Specifications

• Product Name: Automation System
• Model Number: 3U00000001-en-US.08

Product Usage Instructions

Maintenance Procedures

1. Using a lint-free cloth, wipe the interchangeable pipe.
2. Roll the interchangeable pipe again and insert it into the chute. Slide it along the chute length.
3. Put manually the head of the Desealer back in place.
4. Install the Desealer Module cover.
5. Set the Desealer Module in Online status:
6. Click on Overview and select Desealer.
7. Click on Status menu.
8. Select the On-line function button.
9. Wait until the Module is set to online.

Storage and Retrieval Module

1. Empty the condensation liquid tank when full by Good Laboratory Practices.

Consumables
Some Automation Modules need consumables for routine processes. The list of consumables includes:

FAQs

• Q: How do I set the Desealer Module back online?
  A: Follow the steps outlined in the Maintenance Procedures section under Desealer Module.

• Q: What should I do with the condensation liquid tank of the refrigerator unit?
  A: Empty the condensation liquid tank when full following the procedure described under Storage and Retrieval Module.

USING

1. Using a lint-free cloth, wipe the interchangeable pipe.
2. Roll the interchangeable pipe again and insert it into the chute. Slide it all along the chute length.
3. Put manually the head of the Desealer back in place.
4. Install the Desealer Module cover.
5. Set the Desealer Module in On-line status:
   • a. Click on Overview and select Desealer
   • b. Click on Status menu.
   • c. Select On-line function button..
   • d. Wait until the Module is set to On-line.

Verification steps
Verify that the Desealer Module is back online.

Storage and Retrieval Module

Empty the condensation liquid tank

• At the discretion of Laboratory, the condensation liquid of the refrigerator unit can be either collected in a tank or drained in a waste tube of the Laboratory.
• The following procedure describes how to empty the condensation liquid tank of the refrigerator unit when full.

Prerequisites

Task steps

1. Locate the condensate drain pipe (Figure 145 – A) of the refrigerator unit and the condensation liquid tank.
2. Empty the condensation liquid tank when full in accordance with the Good Laboratory Practices.

Verification steps
None.

Some of Automation Modules need of consumables for routine process. The list of consumables that can be supplied is shown below.1

Table 1: Consumables
Refer to the section about Analyzers/Custom Modules for the possible list of consumables addressed to the specific Analyzers/Custom Modules.

References

Access levels
Automation Software provides 4 profiles for User access, with levels increasing from 1 to 4.
Table 2: Profiles for User access

Level| Profile| Access Level| User Type| Validation Level
---|---|---|---|---
1| Laboratory Technician| Operator| Clinical| V1
2| Laboratory Supervisor| Supervisor| V2
3| Physician| Supervisor| Clinical| V3
4| Head Physician| V4

Every Laboratory User is assigned a Username and a personal (non-transferable) password. Furthermore, every User is configured according to one of the levels listed, to log in only to the functions corresponding to their level. New users can be added by the Head Physician, or by contacting technical support.
In addition, the Automation System provides other 2 profiles for User access.
Table 3: Other User levels

Level| Profile| Access Level| User Type| Validation Level
---|---|---|---|---
n/a| Guest| Guest| Viewer| n/a
n/a| FSE| FSE| Technical support| n/a

inpeco.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>