VIQUA 9-IHS10 Whole Home Integrated UV Water Owner’s Manual

May 15, 2024
VIQUA

9-IHS10 Whole Home Integrated UV Water

“`html

Specifications:

  • Models: Arros 9-IHS10, Arros 9-IHS12, Arros 15-IHS10, Arros
    15-IHS12, Arros 15-IHS22, Arros 22-IHS22

  • Brand: VIQUA ArrosTM

  • Website: www.viqua.com

Product Usage Instructions:

Safety Information:

Section 1 Safety Information

It is crucial to read the entire manual before operating the
equipment to prevent personal injury or damage to the system. Pay
close attention to all danger, warning, and caution statements
provided.

Potential Hazards:

  • Read all labels and tags attached to the system to avoid
    personal injury or system damage.

  • Dispose of waste electrical or electronic equipment (WEEE)
    properly; do not discard in the trash.

  • Avoid storing combustible materials near the system.

  • Obey all safety messages and symbols to prevent potential
    injuries.

  • Use safety equipment such as gloves, safety glasses, and safety
    boots as indicated.

Safety Precautions:

DANGER: Follow all safety precautions to avoid
accidents and comply with the manufacturer’s warranty.

WARNING: This product contains chemicals that
can cause harm. Refer to www.P65Warnings.ca.gov for more
information.

FAQ:

Q: How often should I replace the UV lamp in my VIQUA ArrosTM

water system?

A: It is recommended to replace the UV lamp annually to ensure
optimal performance and water safety.

Q: Can I install the VIQUA ArrosTM system myself?

A: Installation should be performed following the provided
installation manual to ensure proper setup and avoid safety
hazards.

“`

Owner’s Manual
VIQUA ArrosTM Models:
Arros 9-IHS10, Arros 9-IHS12, Arros 15-IHS10, Arros 15-IHS12, Arros 15-IHS22, Arros 22-IHS22

425 Clair Rd. W, Guelph, Ontario, Canada N1L 1R1 t. (+1) 519.763.1032 · tf. (+1) 800.265.7246 (US and Canada only) t. (+31) 73 747 0144 (Europe only) · f. (+1) 519.763.5069 e-mail: info@viqua.com
www.viqua.com

520520-R_RevB

Congratulations on the purchase of your ultraviolet (UV) water system! This
system uses the most advanced UV technology on the market and is designed to provide you with years of trouble free operation with minimal maintenance. To ensure ongoing optimal operation, UV lamps need to be replaced annually with VIQUA factory-supplied replacements. VIQUA lamps are the result of extensive development resulting in a highly efficient platform with extremely stable UV output over the entire 9000 hour lifetime. Its success has led to a proliferation of non-genuine copies in the market. The UV lamp is the heart of the UV System, and there should be no compromise when it’s time for a replacement. Why should you insist on genuine factory supplied VIQUA replacement lamps? · Use of widely available, non-genuine, replacement lamps has been shown to
damage the control module of VIQUA UV equipment. · An increasing number of calls to VIQUA Technical Support are connected with non-
genuine lamps being used (unknowingly) as replacements. · Damage arising from the use of non-genuine lamps poses a safety risk and is not
covered by equipment warranty. · Unless the UV equipment is equipped with a UV sensor (monitor), it is not possible to
verify the UV (invisible) output of replacement lamps. · Similar appearance to the original lamp and the presence of (visible) blue light does
not mean equivalent performance. · VIQUA replacement lamps undergo rigorous performance testing and strict quality
control processes to ensure that the safety and performance certifications of the original equipment are not compromised. So, you can see that it’s simply not worth the risk! Insist on genuine VIQUA replacement lamps.
2

Safety Information

Section 1 Safety Information

These are the original instructions. Please read this entire manual before operating this equipment. Pay attention to all danger, warning, and caution statements in this manual. Failure to do so could result in serious personal injury or damage to the equipment.
Make sure that the protection provided by this equipment is not impaired. DO NOT use or install this equipment in any manner other than that specified in the installation manual.

1.1 Potential Hazards:

Read all labels and tags attached to the system. Personal injury or damage to the system could occur if not observed.

Waste electrical and electronic equipment (WEEE). This symbol indicates that you should not discard wasted electrical or electronic equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

This symbol indicates there is a potential for VERY hot water when flow is started.

Hg This symbol indicates there is Mercury present.

This symbol indicates not to store any combustible or flammable material close to the system.

This is the safety alert symbol. Obey all safety messages that follow this symbol to avoid potential injury. When on the equipment, refer to the Operational and Maintenance manual for additional safety information.

This symbol indicates that the contents of the transport package are fragile and the package should be handled with care.

This symbol indicates a risk of electrical shock and/or electrocution exists.

This symbol indicates safety glasses with side protection is required for protection against UV exposure.

This symbol indicates the marked equipment may contain a component that can eject forcibly. Obey all procedures to safely depressurize.

This symbol indicates gloves must be worn.

This symbol indicates the system is under pressure.

This symbol indicates the marked item could inject fluid into the skin.

This symbol indicates there is a potential UV hazard. Proper protection

UV

must be worn.

This symbol indicates the marked item could be hot and should not be touched without care.

This symbol indicates safety boots must be worn.
This symbol indicates the operator must read all available documentation to perform required procedures.
This symbol indicates that the system should only be connected to a properly grounded, grounding-type controller receptacle that is protected by a Ground Fault Circuit Interrupter (GFCI).

3

Safety Information
1.2 Safety Precautions:
DANGER
Failure to follow these instructions will result in serious injury or death. · Electric Shock: To avoid possible electric shock, special care should be taken since water is present near the electrical equipment. Unless a situation is encountered that is explicitly addressed by the provided maintenance and troubleshooting sections, DO NOT attempt repairs yourself, refer to an authorized service facility. · GROUNDING: This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electrical shock. This system is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Improper connection of the equipment-grounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. DO NOT modify the plug provided with this system ­ if it does not fit in the outlet, have a proper outlet installed by a qualified electrician. DO NOT use any type of adapter with this system. · GROUND FAULT CIRCUIT INTERRUPTER PROTECTION: To comply with the National Electrical Code (NFPA 70) and to provide additional protection from the risk of electric shock, this system should only be connected to a properly grounded, grounding-type controller receptacle that is protected by a Ground Fault Circuit Interrupter (GFCI) or to a residual current device (RCD) having a rated residual operating current not exceeding 30 mA. Inspect operation of GFCI as per manufacturer’s suggested maintenance schedule. · DO NOT operate the UV System if it has a damaged cord or plug, if it is malfunctioning or if it has been dropped or damaged in any manner. · DO NOT use this UV System for other than intended use (potable water applications). The use of attachments not recommended or sold by the manufacturer / distributor may cause an unsafe condition. · DO NOT install this UV System where it will be exposed to the weather or to temperatures below freezing. · DO NOT store this UV System where it will be exposed to the weather. · DO NOT store this UV System where it will be exposed to temperatures below freezing unless all water has been drained from it and the water supply has been disconnected.
WARNING
· During extended periods of no water flow, the water in your UV Chamber can become very hot (Approx. 60 °C) and potentially lead to scalding. It is recommended to run your water until this hot water has been purged from your UV Chamber. Do not allow water to contact your skin during this time. To eliminate this condition, a temperature management valve can be installed at the outlet of your UV System.
· Do not pass water through the UV System for a minimum of 5 minutes after applying power (including after power interruptions) to avoid passing under- treated water that may, in rare instances, pose health hazards.
· This system contains a UV Lamp Unit. Do not operate the UV Lamp Unit when it is removed from the UV Chamber. Unintended use or damage of
UV
the system may result in the exposure of dangerous UV radiation. UV radiation may, even in little doses, cause harm to the eyes and skin. · Changes or modifications made to this system without the consent of the manufacturer could render the system unsafe for operation and may void
the manufacturer’s warranty.
WARNING: This product can expose you to chemicals including phthalates, which is known to the state of California to cause cancer, and mercury, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

CAUTION

Failure to follow these instructions could result in minor or moderate injury.

· Carefully examine the UV System after installation. It should not be plugged in if there is water on parts not intended to be wet such as, the controller or lamp connector.

· Hg EXPOSURE: The UV Lamp Unit contains mercury. If the lamp breaks, then avoid inhalation or ingestion of the debris and avoid exposure to

Hg

eyes and skin. Never use a vacuum cleaner to clean up a broken lamp as this may scatter the spilled mercury. Obey local regulations and

guidelines for the removal and disposal of mercury waste.

4

Safety Information

NOTICE
· The Arros 9-IHS10, Arros 9-IHS12, Arros 15-IHS10, Arros 15-IHS12, Arros 15-IHS22 and Arros 22-IHS22 UV Systems have been validated through microbial testing. Through this testing, performance data has been generated for UV dose delivery to inactivate Cryptosporidium, Giardia, Escherichia coli (E. coli) and Fecal Coliform.
· The UV Lamp Unit inside the UV System is rated at an effective life of approximately 9000 hours. To ensure continuous protection, replace the UV Lamp Unit annually.
· The UV System is not to be used or played with by children. Persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, are also not to handle the UV System unless they have been given supervision or instruction.
· This system is intended to be permanently connected to the water lines.
· This system is not intended to be used in or above water or outdoors or used in swimming pools when persons are in the pool.
· EXTENSION CORDS: If an extension cord is necessary, use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole cord connectors that accept the plug from this system. Use only extension cords that are intended for outdoor use. Use only extension cords having an electrical rating not less than the rating of the system. A cord rated for less amperes or watts than this system rating may overheat. Exercise caution when arranging the cord so that it will not be tripped over or pulled. DO NOT use damaged extension cords. Examine extension cord before using and replace if damaged. DO NOT abuse extension cord. Keep extension cord away from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting this system from the extension cord. Never yank cord to pull plug from outlet. Always grasp the plug and pull to disconnect.
· If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
· SYSTEM PROTECTION: To protect your Controller, a UL1449 certified (or equivalent) transient voltage surge suppressor is strongly recommended.
· The UV Lamp Unit in this system conforms to the applicable provisions of the Code of Federal Regulations (CFR) requirements including, Title 21, Chapter 1, Subchapter J, Radiological Health.
· Read and understand the Owner’s Manual before operating and performing any maintenance on this equipment.
· This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
· This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/ TV technician for help.
· Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1.3 Water Chemistry

Water quality is extremely important for the optimum performance of your UV System. The following levels are recommended for installation:

Water Quality and Minerals
Iron Hardness* Turbidity Manganese Tannins UV Transmittance

Level
< 0.3 ppm (0.3 mg/L) < 7 gpg (120 mg/L) < 1 NTU < 0.05 ppm (0.05 mg/L) < 0.1 ppm (0.1 mg/L) > 75% (call factory for recommendations on applications where UVT < 75%)

  • Where total hardness is less than 7 gpg, the UV unit should operate efficiently provided the quartz envelope is cleaned periodically. If total hardness exceeds 7 gpg, the water should be softened. If your water chemistry contains levels in excess of those mentioned above, proper pre-treatment is recommended to correct these water problems prior to the installation of your UV System. These water quality parameters can be tested by your local dealer, or by most private analytical laboratories. Proper pre-treatment is essential for the UV System to operate as intended.

5

General Information
Section 2 General Information
1 2

3

10 10
4

9 8

8

5

6 7

1 2
3

4

5

6

7

4

11

260251-R

Figure 1 UV System Components

Item

Description

Part Number

VA09LU

1

UV Lamp Unit- Hard glass coated UV lamp for long consistent life (9000 hours) sealed within a GE 214 fused quartz sleeve

VA15LU

2 Lamp Head O-ring 3 Arros Controller 100-240VAC/50/60Hz

VA22LU 411173-R VA-CTRL

4 Power Cords for Arros Controller

260251-R 260252-R

5 6
6

Mounting Bracket Clamp Drain Plug O-ring

420619-R 411138-R

260252-R
UV Systems
Arros 9-IHS10 Arros 9-IHS12 Arros 15-IHS10 Arros 15-IHS12 Arros 15-IHS22 Arros 22-IHS22
All Models All Models Arros 9-IHS10 Arros 9-IHS12 Arros 15-IHS10 Arros 15-IHS12 Arros 15-IHS22 Arros 22-IHS22 Arros 9-IHS10/2 Arros 9-IHS12/2 Arros 15-IHS10/2 Arros 15-IHS12/2 Arros 15-IHS22/2 Arros 22-IHS22/2 All Models All Models

Item
7 Drain Plug
8 Sediment filter

Description

Part Number
411111-R CMB-510-HF
CMB-520-HF

9 Carbon filter

10 O-ring 11 Sump wrench
Section 3

Installation of UV System

C2-02PB
OR40-50W WR40-50

Installation of UV System
UV Systems
All Models Arros 9-IHS10 Arros 9-IHS12 Arros 15-IHS10 Arros 15-IHS12 Arros 15-IHS22 Arros 22-IHS22 Arros 9-IHS12 Arros 15-IHS12 Arros 15-IHS22 Arros 22-IHS22
All Models All Models

CAUTION
Electronic controller must be connected to a Ground Fault Protected Circuit (GFCI) receptacle. Ensure green ground wire ring terminal is securely fastened to ground stud on UV Chamber.

3.1 Installing UV System
Note: To reverse inlet port to suit installation plumbing see Section 3.1 procedure 4.

5

INLET

1

A
2
3

OUTLET

Note: UV System should be the final piece of treatment equipment

4

Item
1 2 3
A

Description
Main water shut-off Optional by-pass assembly UV System

Figure 2 UV System

Item

Description

4

Drain Plug

5

Customer supplied GFCI circuit to match voltage

Note: By-pass pipe should be at least 6″ above the Arros UV unit and as close to the wall as possible to ensure lamp can be removed.

7

Installation of UV System
Prerequisites:
· Determine appropriate indoor location for the UV System. Refer to Figure 2.
· Ensure adequate clearance above UV Chamber to allow for removal of the UV Lamp Unit.
· Make sure to turn off the main water supply and depressurize the line.
· Mount the UV System to the wall with appropriate lag bolts through the two mounting holes located on the metal bracket.
· The supplied lag bolts are suitable for attachment to wood. Note: Attachments to other materials will require purchasing of alternative hardware.
· Make all necessary plumbing connections. Refer to Figure 2.
Procedure: 1. Figure 2 shows the installation of a typical UV System and the related components that may be used for the installation.
The use of a by-pass assembly is recommended in case the system requires “off- line” maintenance. In this case, note the system requires a supplementary disinfectant for the distribution system if any water is used during by-pass condition. In addition, during by-pass, the water will NOT be treated and a “DO NOT CONSUME THE WATER” tag should be physically installed on the by-pass assembly until such time as the system is sanitized and returned to service. For more information, refer to Section 3.2. If the water is to be consumed while the system is off-line, the water must be boiled for twenty minutes prior to consumption.
2. Select a suitable location for the UV System and its related components. As it is recommended to install a GFCI, make sure that this is taken into consideration prior to any installation. When selecting a mounting location, leave enough space to allow the removal of the UV Lamp Unit (typically leave a space equal to the size of the UV Chamber itself).

Overall Length (L)
8.5″ (21.6 cm)

Overall Length (L)
16″ (40.6 cm)

Min. clearance equal to UV Chamber overall
Length

Min. clearance equal to UV Chamber overall
Length

Overall Height (H) UV Chamber overall length
Inlet Port

Overall Height (H) UV Chamber overall length
Inlet Port

Overall Depth (D)

Overall Depth (D)

Figure 3 UV System Installation 3. Mount the UV System to the wall using the supplied bracket. Various connection methods can be used to connect the
water source to the system, however union type connectors are recommended. Note: DO NOT solder connections while attached to the system as this could damage the O-ring seals.
8

Installation of UV System

4. Reversing the inlet and outlet ports. Note: If reversal of UV System ports is not required, skip this step and proceed to Step 5.
The factory configuration of the UV System is with the inlet port on the left side of the unit. If required due to plumbing installations then this can be reversed as follows:

4a

1

4b

4c

4d

1

1

x2 2
2

· Remove the locknut found on the back side of the UV System.

x2
· Remove the two Phillips screws that attach the controller unit to the UV Chamber.

4e

4f

1

1
2
180O
· Pull the controller off of the UV Chamber and rotate it 180 degrees.

4g

1

x2 2
· Align the mounting holes on the controller with the welded #10 stud mounts on the UV Chamber and insert the ground wire back onto the threaded stud.

x2

2

1

2

2
· Push the controller firmly down onto the UV Chamber.

x2
· Reassemble the mounting screws to secure the controller to the UV Chamber.

· Tighten down the locking nut to secure the grounding wire.

5. Install the UV Lamp Unit into the UV Chamber. Twist UV Lamp Unit until fully seated then swing lamp connector around and position over top of the lamp and press down until the lamp pins are fully inserted into the lamp connector.

5a

1

5b

5c

1

1

2

UV

2

Hg

2

9

Installation of UV System

6. When all plumbing connections are complete, slowly turn on the water supply and check for leaks. The most likely cause of leaks is from the O-ring seals in either the UV Lamp Unit or the drain plug. To resolve, shut water off and drain the UV Chamber. Remove either the UV Lamp Unit or drain plug, as needed and wipe the O-rings and threads. Clean and re-install.Once it is determined that there are no leaks, plug the system into the ground fault interrupter and check controller to ensure the system is operating properly. The controller should illuminate without any alarms.
Note: It is normal for the drain plug to make a clicking sound during install.
7. Allow the water to run for a few minutes to clear any air or dust that may be in the UV Chamber.
Note: When there is no flow, the water in the UV Chamber will become warm. To remedy this, run a cold water tap anywhere in the house for a minute to flush out the warm water.
8. Once it is determined that there are no leaks, plug the system into the ground fault interrupter and check controller to ensure the system is operating properly. The controller should illuminate without any alarms.
Note: DO NOT look directly at the glowing UV Lamp Unit.

3.2 Cleaning Procedure
The sump housings will be heavy.

CAUTION

Prerequisites:
· Reapply a generous amount of lubricant to the O-ring when reinstalling sumps.
It is imperative that the entire distribution system located after the UV System be chemically cleaned to ensure that the plumbing system is free from any contaminants. The cleaning process must be performed immediately after the UV unit is installed and repeated thereafter whenever the UV System is shut down for service, without power, or inoperative for any reason. The procedure for sanitizing the plumbing system is readily accomplished as follows:

1

2

3

4

· Ensure that the UV System remains powered on for the entire cleaning process.

· Shut off the water supply. · Close each faucet.

· Press the pressure button to release the pressure from the cartridges.

· Remove the drain plug at the bottom of the sump and place a pail to catch the water.
· Reinstall the drain plug.

10

5

6

1

1

2 2

· Loosen the drain plug at the bottom of the UV Chamber and place a pail to catch the water.
· Tighten the drain plug. Note: It is normal for the drain plug to make a clicking sound during install.
9

· Remove the sump housings using sump wrench.
10

7 1

Household 5.25% BLEACH Bleach Solution
2

x2

x2

Maintenance
8
11 2
2

· Remove cartridge(s) and pour 2 cups of household bleach solution into the filter housing(s).
Note: DO NOT use Hydrogen Peroxide.

· Reinstall the housings.

11

12

11

30 mins 0

45

15

30

1

1

2 2

2 2

· Open all faucets and turn on the cold water supply followed by hot water (if available) until you smell the bleach.
· Close all faucets and allow bleach in the water lines for 30 minutes.

· Shut off the water supply. · Remove both housings.

· Reinstall both the cartridges and housings.

· Flush all water outlets until bleach can no longer be smelled (at least 5 minutes).
· Press the pressure button to purge air to complete the cleaning procedure.
· Inspect for any leaks.
· Repair all detected leaks.

Note: 1) The addition of chlorine (bleach) to a hot water tank that has in the past been fed with untreated raw water with high levels of other contaminants (iron, manganese, hydrogen sulphide, organics, etc.) will result in oxidation of these contaminants and may require repeated flushing of the hot water tank. This contingency must be dealt with independently under the start-up procedure for any other conditioners that may form a part of the pre-treatment for the UV unit.

  1. The above cleaning procedure will result in a massive chlorine residual far in excess of the 0.5 to 1.0 mg/L typically present in municipally chlorinated water and of a magnitude consistent with the minimum 50 mg/L chlorine solution recommended for the cleaning of distribution systems known to be contaminated. Do not consume water until complete system has been flushed.

Section 4 Maintenance

WARNING
· Always disconnect power before performing any work on the UV System. · Always shut-off water flow and release water pressure before servicing. · Regularly inspect your UV System to ensure that the power indicators are on and no alarms are present. · Replace the UV Lamp Unit annually upon controller alert, typically after 1 year or 9000 hours of operation. · Always drain the UV Chamber when closing a seasonal home or leaving the unit in an area subject to freezing temperatures.

11

Maintenance

4.1 Replacing UV Lamp Unit Assembly
NOTICE
· Refer to Section 5.1. Refer to www.lamprecycle.org for lamp disposal. · DO NOT use water during replacement of UV Lamp Unit.
UV Lamp Unit replacement is a quick and simple procedure requiring no special tools. The UV Lamp Unit must be replaced after 9000 hours of continuous operation (approximately one year) in order to ensure adequate performance.

Procedure:

1

2

3

1

4

1

2

UV

· Shut off the water line to UV Chamber and release system pressure before servicing.

10 mins 0

45

15

30

· Disconnect main power source and allow the unit to cool for 10 minutes.

5

1

2

UV

6

1

Hg
2

· To remove lamp connector from the UV Lamp Unit, pull lamp connector straight up until the pin sockets disengage from the UV Lamp Unit pins.
· Rotate lamp connector clockwise until a stop is hit. Then press down to lock in the service position.

· To remove UV Lamp Unit, rotate counter clockwise until the UV Lamp Unit becomes free from the bayonet mounting taps.
· Carefully pull UV Lamp Unit straight out from UV Chamber ensuring the UV Lamp Unit does not contact the UV Chamber.
· Always hold the UV Lamp Unit by the plastic lamp head.

7

8

Hg

2

· Insert the new UV Lamp Unit fully into the UV Chamber and rotate clockwise until UV Lamp Unit is fully inserted and aligns with the lock position shown on the controller top.

· Rotate lamp connector counter clockwise from the service position so it is over top of the UV Lamp Unit connector pins.
· Press down until the lamp connector fully engages the UV Lamp Unit pins.

· Open each faucet and turn on water supply.
· Inspect for any leaks. · Repair all detected leaks.

· Reapply power to the UV System. The End of Lamp timer should now show 365 days remaining.
· Perform the cleaning procedure. Refer to Section 3.2.

12

Maintenance

4.2 Cleaning UV Lamp Unit Assembly Quartz Envelope
Minerals in the water slowly form a coating on the quartz envelope. This coating must be removed because it reduces the amount of UV light reaching the water, thereby reducing performance. If the envelope cannot be cleaned the UV Lamp Unit assembly must be replaced.

Prerequisites:

· Shut off water supply and drain all lines.

· Depressurize the UV System. Place a small pail under the UV System to catch any spills.

· Remove the UV Lamp Unit. Refer to Section 4.1.

Procedure:

1

2

3

1

4

1

2

UV

Hg

2

Mild Acid

· Clean the quartz envelope with a cloth soaked in CLR, vinegar or some other mild acid and then rinse with water.

· Insert the new UV Lamp Unit fully into the UV Chamber and rotate clockwise until UV Lamp Unit is fully inserted and aligns with the lock position shown on the controller top.

· Rotate lamp connector counter clockwise from the service position so it is over top of the UV Lamp Unit connector pins.
· Press down until the lamp connector fully engages the UV Lamp Unit pins.

· Open each faucet and turn on water supply.
· Inspect for any leaks. · Repair all detected leaks. · Perform the cleaning
procedure. Refer to Section 3.2.

13

Maintenance
4.3 Replacing Cartridges
The sump housings will be heavy.

CAUTION

It is recommended to change the filter cartridges regularly, approximately 3-4 times per year depending on water quality and usage. A gradual drop in water pressure after the filtration device is an indication that the pre-filter cartridges are nearing the end of their useful life.
Procedure:

1

2

3

4

10 mins 0

45

15

30

· Disconnect main power source and allow the unit to cool for 10 minutes.

· Shut off the water supply. · Close each faucet.

5

6

Old

New

· Press the pressure button to release the pressure from the cartridges.
7

· Remove the drain plug at the bottom of the sump and place a pail to catch the water.
· Reinstall the drain plug.
8

1

1

2 2

· Remove the housing(s) using sump wrench.

· Remove and discard the old cartridge(s).
· Install new cartridge(s).

11 2
2
· Reinstall the housing(s).

· Open a faucet downstream of the system.
· Restore power and turn on the water supply.
· Close the downstream faucet. · Press the pressure button to
purge air.

14

Operations
Section 5 Operations WARNING
The advanced warning system has been installed to provide the optimum protection against microbiological contamination in water. DO NOT disregard the warning signals. The best way to ensure optimum UV performance is to have the water microbiologically tested by a recognized testing agency on a regular basis.
5.1 UV System Operation
Note: Firmware updates may modify the UI screens and processes. If necessary, refer to the online manual for most up-todate information.
5.1.1 Start Up Sequence
1. During the startup sequence the Controller will cycle through the following screens: (Use the arrows to scroll and press when the appropriate value is displayed) a. Language Selection: English, French, Spanish with English being the default option.
Figure 4 Language Selection b. Model Select: Pressing the ? Icon will direct you to where the model number label can be found.
Figure 5 Model Select
15

Operations
c. Screen Orientation Setup: Press No to skip this step.
Figure 6 Startup Sequence d. Warranty Registration (Recommended): Follow the QR code to www.trojantechnologies.com/register to complete
the online registration. Once completed (or if skipping this step), press Done to complete the Startup Sequence.
Figure 7 Warranty Registration
5.2 Home Screen
1. The Home Screen displays the lamp life remaining and counts down from 365 to 0 days as the system is ON. 2. The Home Screen also displays Lamp Status ON/OFF. 3. A Minor Warning Alarm is initiated once the lamp life reaches 30 days remaining and will also alarm when the lamp life
reaches 14 days remaining.
16

Operations
4. A Major Lamp Alarm will be initiated once the lamp life reaches 0 days. Notes: 1) The UV System Wi-Fi capability is for firmware updates only (Section 5.5) and is not capable of system status or control. 2) Use of a non-VIQUA UV Lamp Unit will result in an ongoing fault mode (major lamp alarm) and will impair accurate lamp-life tracking.
Lamp On
Minor Alarms
Major Alarms Lamp Fault/Lamp Life expired Figure 8 Home Screen 17

Operations

5.3 Menu Screen
1. From the Home Screen, press the top left

icon to access the main menu screen.

2. The Menu Screen provides access to four main user screens:

Figure 9 Menu Screen a. A spare parts menu screen for finding replacement part numbers.
Figure 10 Spare Parts Menu b. A Setting menu for setting or changing system settings such as System model number, Display and Halo brightness,
orientation, user language, screen saver time, and Reset that returns all settings back to default settings.
Figure 11 Settings Menu 18

Operations
c. Information menu which provides system information such as firmware version, Model number and serial number.

Figure 12 Information Menu d. Contact dealer information menu provides information on finding a dealer in your area.

Figure 13 Contact Dealer Information Menu
5.4 Lamp Head Status Lights
The white top cap (Halo) of the lamp assembly will illuminate when the lamp is operating. For normal operation (no faults, lamp on), the top cap is blue. When there is a minor alarm condition (lamp life less than 30 days left), the top cap is amber. When there is a major alarm condition, the cap will be red.

Blue Halo

Amber Halo

Red Halo

Figure 14 Lamp Head Status Lights 19

Troubleshooting
5.5 Firmware Updates
Firmware updates are released periodically to enhance the performance or add features to the controller. New firmware can be uploaded to the controller using the VIQUA app from a smart phone or tablet.
Scan the QR code or click the link below to download the VIQUA app:

Figure 15 iOS Devices For more details on this feature, go to: www.trojantechnologies.com.
Section 6 Troubleshooting

Figure 16 Android Devices

Symptom
No Power GFCI or circuit breaker repeatedly trips Leak at inlet or outlet Leak detected from area of UV Chamber Alarm System is operating but water tests reveal bacterial contamination
Pressure Drop
High Bacteria Counts
Heated Product Water Water Appears Milky
Unit Leaking Water

Possible Cause
GFCI and or circuit breaker has tripped Transient voltage surge suppressor damaged Controller damaged Connection between lamp and lamp plug is wet Short circuit in electrical assembly Threaded pipe fittings are leaking Condensation of warm moist air on cold UV Chamber (slow accumulation) O-rings damaged, deteriorated or incorrectly installed UV Lamp Unit not properly installed (not fully inserted into controller lamp locking assembly) Refer to Alarm Menu Sec 5 Equipment downstream of UV System is acting as a breeding ground for pathogens Pathogens are residing in the distribution lines post UV
Recontamination from pipe dead-ends
Sediment Pre-Filter clogged
Flow regulator
UV Lamp Unit quartz envelope is stained or dirty
Change in feed water quality
Contamination in water lines after UV System
Possible break-through of sediment through pre-filter
Common problem caused by infrequent use of water Caused by air in the water lines Problem with O-ring seal on Lamp Assembly or Drain Plug Assembly Condensation on UV Chamber caused by excessive humidity and cold water Inadequate inlet/outlet port connections

Possible Solution
Reset GFCI and or circuit breaker Replace TVSS Replace controller and use a TVSS Clean and dry area around the lamp and lamp connector, check unit for leaks or condensation Replace controller Clean threads, reseal with Teflon tape and re tighten
Control humidity or relocate unit
Inspect o-rings and replace if deteriorated. Tighten and ensure lamp assembly is fully inserted into controller locking assembly Follow alarm menu help guidance
Ensure UV is the last piece of treatment equipment
Ensure all distribution lines have been disinfected with chlorine. Refer to Section 3.2. Remove any pipe dead-ends and flush with chlorine. Refer to Section 3.2. Replace filter cartridge with appropriate 5 micron cartridge. Note: Check source water supply as fluctuations may occur in source pressure Flow regulator will result in pressure drop when approaching full flow. Clean quartz envelope of UV Lamp Unit with scale cleaner and eliminate the source of staining problem (i.e soften hard water) Refer to Section 4.2. Have source water tested to ensure that water quality is still within allowable limits for this system. It is imperative that effluent water stream be shocked with chlorine (bleach) before water leaves UV System – the system must have a bacterial free distribution system to work effectively. Refer to Section 3.2. Have source water tested for turbidity- may need stepped filtration in order to catch all sediment entering water system (20 micron filter followed by a 5 micron filter followed by the UV System) Run water until it returns to ambient temperature Run water until air is purged Ensure O-ring is in place, check for any cuts or abrasions, clean O-ring, moisten with water/lubricant and re- install, replace if necessary
Check location of UV System and control humidity
Check thread connections, reseal with Teflon tape and retighten connection

20

Manufacturer’s Dose Flow Chart

Symptom
System shutting down intermittently
Lamp Failure Alarm on New Lamp
Leak detected at filters

Possible Cause
Interrupted Controller
Loose connection between lamp and lamp connector Moisture build up in connector may keep lamp and connector from making a solid connection O-ring damaged, deteriorated or incorrectly installed Filter cartridge not centered

Possible Solution
Ensure system has been installed on its own circuit as other equipment may be drawing power away from UV (ie pump or fridge) UV System should not be installed on a circuit which is incorporated into a light switch Disconnect lamp from connector and reconnect, ensuring that a tight fit is accomplished Eliminate chance of any moisture getting to the connector and/ or lamp pins Remove the sump, wipe the O-ring and threads clean. Ensure the O-ring is fitted properly, then reinstall. Remove sump, check for cartridge damage, re- assemble ensuring cartridge is centered.

Section 7 Manufacturer’s Dose Flow Chart

UV Dose Curves at 95% UVT @ EOL 50

45

40

35
Arros 22
30

Flow Rate US (gpm)

25
Arros 15
20

15
Arros 9
10

5

0 0 5 10 15 16 20 25 30 35 40 45 50 55 60

UV Dose (FLUENCE) (mJ/cm2)
Note: dosage based on 95% UVT at end of lamp life (EOL)

1966 US Public Health

Manufacturer’s NSF/EPA,

Standard

Standard

Note: Not performance tested or cerfied by NSF Figure 17 Dose Flow Chart 21

Specifications
Section 8

Specifications

Flow Rate1 Not performance tested or certified by NSF

Model

Arros 9 IHS10

Arros 9 IHS12

Arros 15 IHS10

Arros 15 IHS12

Arros 15 IHS22

Arros 22 IHS22

US Public Health 16mJ/cm2 @ 95%UVT

17 gpm (64.3 lpm) (3.86 m3/hr)

29 gpm (109.8 lpm) (6.59 m3/hr)

42 gpm (159 lpm) (9.54 m3/hr)

VIQUA Standard 30mJ/cm2 @ 95%UVT
NSF/EPA 40mJ/cm2 @ 95%UVT

9 gpm (34.1 lpm) (2.0 m3/hr)
7 gpm (26.5 lpm) (1.59 m3/hr)

15 gpm (56.8 lpm) (3.41 m3/hr)
12 gpm (45.4 lpm) (2.73 m3/hr)

22 gpm (83.3 lpm) (5.0 m3/hr)
16 gpm (60.6 lpm) (3.63 m3/hr)

UV Chamber

28.4 cm x 10.16 cm (11.2″ x 4.0″)

42.0 cm x 10.16 cm (16.5″ x 4.0″)

57.2 cm x 10.16 cm (22.52″ x4.0″)

Dimensions

Controller

26.67 cm x 12.7 cm x 16.51 cm (10.5″ x 5.0″ x 6.5″)

Overall (L x H x D)

43.0 cm x 44.5 cm x 22.9 cm
(16.95″ x 17.5″ x 9.0″)

63.4 cm x 69.9 cm x 22.9 cm
(24.95″ x 27.5″ x 9.0″)

43.0 cm x 52.9 cm x 22.9 cm
(16.95″ x 20.82″ x 9.0″)

63.4 cm x 69.9 cm x 22.9 cm (24.95″ x 27.5″ x 9.0″)

Inlet Port Size

3/4″ FNPT

Outlet Port Size

3/4″ MNPT

Shipping Weight Voltage2

40lbs (18.1kg)

46lbs (20.9kg)

40lbs (18.1kg)

46lbs (20.9kg)

100-240 V / 50/60 Hz

50lbs (22.7kg)

50lbs (22.7kg)

Electrical

Max. Current

1.5 Amp

Power consumption

35 W

50 W

65 W

Lamp Watts

24 W

38 W

52 W

Maximum Operating Pressure Ambient Water Temperature

100 psi (6.9bar) 2-40 °C (36-104 0F)

Lamp Type

High Output

Display

LCD Touch Screen

Lamp Replacement Reminder

Yes

Visual Lamp Life

Yes

True Lamp Running time

Yes

System Total Running Time

Yes

UV Chamber Material
1Flow rates based on End of Lamp Life; 20°C. 2Units ending in “/2” are for 230V applications.

304 SS

22

Section 9 Manufacturer’s Warranty

Manufacturer’s Warranty

Our Commitment VIQUA is committed to ensuring your experience with our products and organization exceeds your expectations. We have manufactured your UV System to the highest quality standards and value you as our customer. Should you need any support, or have questions about your system, please contact our Technical Support team at 1.800.265.7246 or technicalsupport@viqua.com and we will be happy to assist you. How to Make a Warranty Claim Note: To maximize the performance and reliability of your VIQUA product, the system must be properly sized, installed and
maintained. Guidance on the necessary water quality parameters and maintenance requirements can be found in your Owner’s Manual. In the event that repair, or replacement of parts covered by this warranty are required, the process will be handled by your dealer. If you are unsure whether an equipment problem or failure is covered by warranty, contact our Technical Support team at 1.800.265.7246 or e-mail technicalsupport@viqua.com. Our fully trained technicians will help you troubleshoot the problem and identify a solution. Please have available the model number (system type), the date of purchase, the name of the dealer from whom you purchased your VIQUA product (“the source dealer”), as well as a description of the problem you are experiencing. To establish proof of purchase when making a warranty claim, you will either need your original invoice, or have previously completed your product registration online. Specific Warranty Coverage Warranty coverage is specific to the VIQUA range of products. Warranty coverage is subject to the conditions and limitations outlined under “General Conditions and Limitations”. Ten-Year Limited Warranty for VIQUA UV Chamber VIQUA warrants the UV Chamber on the VIQUA product to be free from defects in material and workmanship for a period of ten (10) years from the date of purchase. During this time, VIQUA will repair or replace, at its option, any defective VIQUA UV Chamber. Please return the defective part to your dealer who will process your claim. Five- Year Limited Warranty for Electrical and Hardware Components VIQUA warrants the electrical (controller) and hardware components to be free from defects in material and workmanship for a period of five (5) years from the date of purchase. During this time, VIQUA will repair or replace, at its option, any defective parts covered by the warranty. Please return the defective part to your dealer who will process your claim. One-Year Limited Warranty for UV Lamp Units VIQUA warrants UV Lamp Unit to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. During this time, VIQUA will repair or replace, at its option, any defective parts covered by the warranty. Your dealer will process your claim and advise whether the defective item needs to be returned for failure analysis. Note: Use only genuine VIQUA replacement UV Lamp Units in your system. Failure to do so may seriously compromise performance and affect warranty coverage. General Conditions and Limitations None of the above warranties cover damage caused by improper use or maintenance, accidents, acts of God or minor scratches or imperfections that do not materially impair the operation of the product. The warranties also do not cover products that are not installed as outlined in the applicable Owner’s Manual. Parts repaired or replaced under these warranties will be covered under warranty up to the end of the warranty period applicable to the original part. The above warranties do not include the cost of shipping and handling of returned items. The limited warranties described above are the only warranties applicable to the VIQUA range of products. These limited warranties outline the exclusive remedy for all claims based on a failure of or defect in any of these products, whether the claim is based on contract, tort (including negligence), strict liability or otherwise. These warranties are in lieu of all other warranties whether written, oral, implied or statutory. Without limitation, no warranty of merchantability or of fitness for a particular purpose shall apply to any of these products. VIQUA does not assume any liability for personal injury or property damage caused by the use or misuse of any of the above products. VIQUA shall not in any event be liable for special, incidental, indirect or consequential damages. VIQUA’s liability shall, in all instances, be limited to repair or replacement of the defective product or part and this liability will terminate upon expiration of the applicable warranty period.

23

425 Clair Rd. W, Guelph, Ontario, Canada N1L 1R1 t. (+1) 519.763.1032 · tf. (+1) 800.265.7246 (US and Canada only)
t. (+31) 73 747 0144 (Europe only) · f. (+1) 519.763.5069 e-mail: info@viqua.com www.viqua.com

FR Cet appareil se recycle

À DÉPOSER À DÉPOSER EN MAGASIN EN DÉCHÈTERIE
OU

Points de collecte sur www.quefairedemesdechets.fr Privilégiez la réparaon ou le don de votre appareil !

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals