SZFEIC FC11 LED Flashlight User Manual
- May 15, 2024
- SZFEIC
Table of Contents
FC11 LED FLASHLIGHT
User Manual
- Button
- Power Indicator Light
- USB Type-C Charging Port
- Rechargeable Battery
Turbo Mode：3.2h
High Mode： 10.3h
Medium Mode：26.4h
Low Mode： 88h
A: Output: Lumens
B: Runtime: Hours
FC11 Flashlight
- Using one CREE XML3 high-brightness lamp bead, the lifespan is 50000H.
- Powered by one ARB-D21-5000mAh rechargeable Li-ion battery. The original battery comes with a charging port.
- The circuit adopt long battery life constant current, super long battery life.
- Anti-reverse connection design to prevent circuit damage caused by battery reverse installation.
- One button controls all functions.
- Adopt double-sided anti-reflection tempered glass lens, the lighting is very clear.
- Weight: 92g(battery weight not included).
- Size: Φ28*130mm.
Operating Instructions
- Please take out the battery insulating sheet from the battery compartment for first time use.
- Power On/Off: Press and hold the button for 2 seconds to switch on and off.
- Gear Switching: In the power-on state, click the button to switch gears. The first power-on gear is the medium gear, click the button to switch the gear, and then cycle through medium-high-turbo-low.
- Strobe Mode: Double-click the button in any state to turn on the strobe mode. Click the button to turn off the strobe mode, it will back to the memorized mode.
- Gear Memory Function: The current gear is memorized when the machine is turned off. It will start to work in the current memorized mode the next time.
Charging Instructions
- Take the battery out of the flashlight, insert the charging cable into the battery positive charging port, the charging indicator light (green light flash), in normal charging process; the charging indicator light (green light on), fully charged. After fully charged, please remove the charging cable in time. Put the battery back into the flashlight and it can be used normally (Please do not reverse installate battery).
Battery Power Indicator
-
Button indication light: When the battery is installed, if the button indicator light is green light on, indicating that the battery is fully charged and can be used normally. If the button indicator light is red light on or red light flash, indicating that the battery is low power, please take out the battery to charge it.
-
Power Inquiry : When the flashlight is turned off, single click the switch button to observe the button indicator light:
Indicator Light Green light On(50%-1000% Power)
Indicator Light Red light On(10%-50% Power)
Indicator Light Red light flash(0%-10% Power)
When indicator light red light flash, please take out the battery to charge it. -
During use process, if the button indicator light red light flash, it means that the battery power is low, which remind user to charge it in time.
Technical Parameters
ANSI/PLATO FL1
| Turbo| High| Med|
Low
---|---|---|---|---
Output|
1100 Lumens
| 600 Lumens| 100 Lumens|
25 Lumens
Runtime|
3 hours 20 minutes
| 10 hours 30 minutes | 26 hours 40 minutes|
88 hours
Range|
214 meters
| 158 meters| 65 meters|
38 meters
Light Intensity|
11515 candela
|
6280 candela
| 1088 candela|
368 candela
Impact Resistance |
1.5 meters
Waterproof|
IPX8
Test Conditions: One ARB-D21-5000mAh rechargeable lithium-ion battery, temperature 21±3°C, humidity 50%-80%.
- FC11 Flashlight has temperature control protection function, the runtime marked in the table is the cumulative time.
Use and Maintenance
- Do not disassemble the sealing parts of the lamp, otherwise the warranty will be invalidated and the lamp may be damaged.
- Please use high-quality batteries, and take out the batteries from the lamp when the lamp is not used for a long time, otherwise the lamp may be damaged due to battery leakage.
- After long-term use, the O-ring of the lamp may be damaged. If this happens, please replace the O-ring in time to maintain the waterproof performance of the lamp.
- Please clean the conductive surface of the lamp frequently to ensure the normal operation of the flashlight, especially when the lamp flickers abnormally or cannot be turned on. The following are the main reasons why the lamps flicker abnormally or fail to light up:
(1) Low battery power.
• Solution: Charge or replace the battery (please pay attention to the
direction when inserting the new battery).
(2) The thread is soiled, or the conductive contact surface/contact point of
the PCB is soiled.
• Solution: Clean the thread or clean the conductive contact surface /contact
points of the PCB with an alcohol swab.
If the above methods do not work, please contact the dealer and follow the
terms of after-sales service for warranty
Battery Specification
Type
| Dimensions| Nominal Voltage| Usability|
Remark
---|---|---|---|---
ARB-D21 series
| 21700| 3.7V| Recommended|
ARB-D18 series| 18650| 3.7V| Recommended|
Need Match With Conversion Sleeve
Non-rechargeable Battery (Li-ion)
| CRA123| 3V| Available| Need Match With Conversion Sleeve
Rechargeable Battery (Li-ion)| 21700| 3.7V| Caution* |
Rechargeable Battery (Li-ion)
| 18650| 3.7V| Caution* |
Rechargeable Li-iron phosphate Battery| 21700| 3.7V|
Banned
|
Rechargeable Li-iron phosphate Battery
| 18650| 3.7V|
Banned
|
- Note: 21700 lithium ion (Li-ion) battery is an industrial battery, not a civil battery with safety guarantee. When the battery due to poor quality or improperly used (short circuit, high temperature, etc.), it may burn, explode and endanger personal and property safety. If using “Caution*” battery types, you should understand the risks and voluntarily assume corresponding responsibilities. High-quality Li-ion battery with protective circuit will reduce risks.
Packing List
- FC11 Flashlight, ARB-D21-5000mAh Battery, Fixed clip, USB Type – C Charging Cable, Sealing Ring, Manual, Warranty Card.
Warning
- To avoid eye damage caused by high-brightness flashlights, please do not look directly at the LED light source of the flashlight.