SPRINT INTERCOM PA-WMCAB-W CCTV Secure Wall Mount Cabinet Installation Guide

SPRINT INTERCOM PA-WMCAB-W CCTV Secure Wall Mount Cabinet

Specifications

• Product Name: PA-WMCAB-W
• Type: Wall Mount Cabinet
• Capacity: Up to 2U height, 490mm width, 400mm depth
• Monitor Compatibility: Up to 24” LCD monitor*

Product Usage Instructions:

Installation Guide:
Follow the steps below for installing the DVR/NVR Secure Wall Mount Cabinet:

1. Unboxing and Pre-Installation Check:
   Handle the approximately 18Kg cabinet with care during unboxing. Open the end opposite to the product label, place the open end on the floor or table, slide the box up, and remove it. Ensure the two cabinet lock keys are fixed to the side packing foam.

2. Wall Mounting Panel:
   Refer to Figure 1 for guidance on mounting the wall panel correctly.

3. Wet Compartment Cable Entry:
   Use Figure 2 as a reference for cable entry in the wet compartment.

4. Dry Compartment Cable Entry:
   Figure 3 illustrates how to manage cable entry in the dry compartment.

5. Cable Management:
   Secure your cables using the provided cable tie mounts. Ten pieces are supplied for this purpose as shown in Figure 5.

6. DVR/NVR Mounting Plate
   Install your DVR/NVR on the mounting plate following the installation notes provided.

FAQ

• Q: Can this product be used in highly corrosive environments?
  A: No, this product is not suitable for highly corrosive environments.

• Q: What monitors are recommended for use with this cabinet?
  A: We recommend using slimline thin bezel monitors with a maximum size of 540x340x45 WxHxD. Other monitors may not fit properly.

PA-WMCAB-W
TECHNICAL AND INSTALLATION GUIDE
CCTV Secure Wall Mount Cabinet

TECHNICAL AND INSTALLATION GUIDE

PA-WMCAB-W – INSTALLATION GUIDE – DVR / NVR Secure Wall Mount Cabinet
The Cabinet – DVR/NVR shelf has a capacity of up to 2U height, 490mm width & 400mm depth,
with space to mount up to a 24” LCD monitor*. It can accommodate most DVR/NVR’s and other access control and alarm system, making it a versatile Controller Cabinet

Product features:

• Compact: size 585(W) x 650(H) x 180(D)mm (closed)
• Capacity: 2RU, 200~490mm width, 400mm depth
• Cable management knock-outs are in the wet and dry compartment
• Ventilation: Temperature controlled 12VDC Low Noise Fan and air intake filter
• Fits up to 24” monitor, with 75/100 VESA mounts
• 2 x cabinet locks use padlocks for additional security
• 30kg cabinet load bearing capacity (10kg vertical shelf)
• 440mm width between mounting points to fit wall studs
• SPCC steel construction and white powder coating
• 4 x outlet power distribution unit(included)
• Temperature controlled Cooling Fan (included)
• Cooling Fan Power Supply (12VDC 1A included)
• 1.5m Power Cord included.
• Ensure that the monitor has horizontal / downwards-facing input ports & power connectors
• NOTE : We recommend only using slimline thin bezel monitors (max Size 540x340x45 WxHxD); other monitors may not fit.
• 4 x M4 x 10mm screws included for monitor mounting
• 4 x washers included – to be ONLY used as a spacer if the monitor bracket fits into a recess at the back of the monitor.

Shipping Weight and Dimensions

Cabinet Dimensions
~ Width-585mm ~ Height – 650mm ~ Depth – 180mm ~ Weight 16.5Kg

Packing Dimensions
Width-630mm ~ Height – 690mm ~ Depth – 230mm ~ Weight 18Kg

UNBOXING and PRE-INSTALLATION CHECK
The cabinet is approximately 18Kgs and care should be taken when unboxing.
Suggested: open the end opposite to the product label and place open end on the floor or table. Slide the box up and remove.
2 cabinet lock keys will be fixed to the side packing foam.

INSTALLATION

• It is recommended that the cabinet be mounted in a well ventilated area.
• The Right side of the cabinet must have a minimum of 200mm clear space
• The bottom of the cabinet must have no less than 300mm clear space
• Once a suitable location is found, mount the box with the center of the monitor bracket at eye level.
• It is recommended that the top mounting holes be at least 1600-1700mm from the floor.
• Use M6x50mm wood, metal or masonry screws secure the box to the wall.
• Use the 2 top mounting KEYHOLE type anchor points first 440mm apart.
• Use the 2 bottom mounting slot holes to level and secure the cabinet to the wall
• Ensure all 4 mounting screws are secure.

Wall Mounting Panel

Wet Compartment Cable Entry

• Remove 4 long screws securing the Wet compartment panel to the box
• Choose appropriate knock-outs for the cables that will enter the cabinet. (25/40/50mm)
• Fit Plain to Screw adapter to the bottom cover. (Screw adapters not supplied with the kit)
• Pull Cables into wet compartment( see image below)
• Gently knock out 12mm holes in dry compartment (See fig.3)

Dry Compartment Cable Entry

Use Cable tie mounts to secure your cables. (10pcs supplied)

DVR/NVR Mounting Plate

• Remove 6 M4 screws securing the NVR mounting plate to the door and tilt up
• Adjust the mounting brackets to the width of the NVR using the M4 wing nuts

Installation Notes

• It is highly recommended to use Plain to Screw adapters and IP68 – M12 cable glands for cable entry into the cabinet
• All Mounting holes and Cable entry holes must be sealed with an water-proof sealant.
• Do not install the cabinet in a highly corrosive enviroment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>