hykolity 65141886 52 Inch Ceiling Fan With Light User Manual

hykolity 65141886 52 Inch Ceiling Fan With Light

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.

2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local electrical codes.
   Electrical installation should be performed by a qualified licensed electrician.

3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg). Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs. (15.9 kg) or less.”

4. Do not place objects in the path of the blades.

5. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly ampened cloth will be suitable for most cleaning.

6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

7. All setscrews must be checked and retightened where necessary before installation.

   • WARNING: To reduce the risk of electrical shock or fire,not use this fan with any solid-state fan speed ontrol device. It will permanently damage the electronic circuitry.
   • WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
   • WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support of 35 lbs. (15.9Kg) or less” and use screws provided with the outlet box.
   • WARNING: To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring.
   • WARNING: Please install with an isolating wall control/switch to avoid the risk of electrical shock.
   • CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box.
   • CAUTION: Please use carefully to avoid injury for yourself or damage of other items when working around or cleaning the fan.
   • CAUTION: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor.
   • CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the quipment.

Dimension Reference

Hardware Included

Fan Parts Included

Exploded View

Installation Instructions

Step1 Attaching the Fan Blades
Remove the motor housing by unscrewing the screws with a screwdriver.
Fasten blades to motor assembly using the screws and paper washers.
Install the motor housing back to the motor assembly, tighten it with screws.
(see figure 1)

WARNING: To reduce the risk of personal injury, do not bend the blade holders while installing, balanc-ing the blades, or cleaning the fan. Do not insert foreign objects between rotating fan blades.

Step2 Assembling the Fan

• Loosen the set screws in the joint until the inside of the channel is clear of the screw tip.
• Remove the Safety pin, Cotter pin from the downrod.
• Route wires exiting from the top of the fan motor through the coupler/canopy and then through the downrod/hang-er ball. (see figure 2)
• Align the holes at the bottom of the downrod with the holes in the joint on top of the motor assembly.
• Carefully insert the safety pin through the holes in the joint and downrod. Be careful not to jam the pin against the wiring inside the downrod. Insert the cotter pin through the hole near the end of the safety pin until it snaps into its locked position.
• Tighten the two setting screws at the joint.

CAUTION: To ensure wobble-free operation and to avoid damage to the fan, the downrod and the set crew must be completely tightened.

Step3 Attaching the Mounting Bracket
Pass the 120-Volt supply wires through the center hole in the mounting bracket.
Install the ceiling mounting bracket on the outlet box using the two mounting screws provided with the outlet box. If necessary use leveling washers (not included) between the mounting bracket and outlet box.
Note that the flat side of the mouting bracket is toward the outlet box.
Securely tighten the two outlet box screws.(see figure 3)

WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support of 35 lbs. (15.9Kg)
or less” and use screws provided with the outlet box.

Step4 Hanging the Fan
Place the hanger ball into the mounting bracket socket. Make sure the hanger ball is fully embedded in the mounting bracket slot and is not loose. (see figure 4)
This will allow you to make the electrical connections. (see figure 6)

Step5 Installing Receiver Assembly
Connect receiver to mounting bracket as shown. Ensure all the electrical connections (see Step 6) are tight and secure to the fan motor assembly. Make sure the fan is earthed correctly as shown. (see figure 5)
After completing the above steps, raise the canopy to cover the receiver and bracket. Once secure and no cables or antenna are visible, then screw down the sides of the canopy. (see Step 7)

Step6 Electrical Connection
Remember to disconnect the power.
Follow the steps below to connect the fan to your household wiring. (see figure 6)
Use the wire connecting nuts supplied with your fan.
Secure the connectors with electrical tape.
Make sure there are no loose strands or connections.

Between fan and receiver:

• Connect the white wire marked “MOTOR N” from the fan to the white wire marked “TO MOTOR N” from the receiv-er.
• Connect the black wire marked “MOTOR L” from the fan to the black wire marked “TO MOTOR L” from the receiv-er.
• Connect the blue wire marked “LIGHT” from the fan to the blue wire marked “FOR LIGHT” from the receiver.
• Between receiver and mains:
• Connect the black live wire marked “AC IN L” from the receiver to the live wire (typically black) from the outlet box. Connect the white neutral wire marked “AC IN N” from the receiver to the neutral wire (typically white) from the outlet box.
• Connecting ground cables:
• Connect the green ground cable of the fan and the green ground cable on the installation cover to the green ground cable on the outlet box.

Step7 Mounting the fan Canopy

• Remove the two non-slotted mounting screws on the top of the canopy.
• Back the two slotted screws out about half way.
• This will enable you to remove the mounting cover plate from canopy.
• Align the locking slots of the ceiling canopy with the two canopy screws in the mounting cover plate.
• Push up to rengage the slots and turn clockwise to lock in place.
• Firmly tighten the two canopy screws.
• Install the two canopy screws into the holes in the canopy and tighten firmly.(see figure 7)

Step8 Installation of Lighting Fixture
Loosen the three screws on the lighting fixture .
A wire connector (female) is located inside the fan motor assembly and a male connector extends from the light-ing fixture. Push them together.
A wire connector (male) is located inside the fan motor assembly and a female connector extends from the light-ing fixture. Push them together.
Lock the junction box with three screws. (see figure 8)

NOTE: The safe distance between the fan blade and the wall shall not be less than 25cm (10 inches) .

(see figure 9)

Step9 Installing the Bulb
Install three LED bulbs(not included) and screw them in clockwise until fastened.(see figure 10)

Care and Cleaning

WARNING: Make sure the power is off before cleaning your fan.

• Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
• Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
• You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
• You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.
• Always unplug the fan before cleaning, disassembly or servicing.

Operation

Transmitter Functions

• Install the AAA 1.5VX2 battery. (NOT INCLUDED) (see figure 11) Attention:To prevent damage to transmitter remove the battery if not used for long periods.
• Restore power to ceiling fan and test for proper operation.
• The fan remote control controls the fan setting(see figure 12):
• +:Upward speed regulation.
• -:Downward speed regulation.
• LIGHT ON/OFF:Press and release immediately to turn on or off the light. DIMMER:Press and hold to dim or brighten lights to the desired level and release.(Note: This function is not enabled with this unit. The light of the fan is non-dimmable.)
• Time:Set timing function 2H 4H 8H

Installing the Remote Control Holder

• Install the wall plug onto the wall, then attach the remote control holder with the two remote control holder mounting screws. (see figure 13)

• Forward and Reverse Direction Function

• This ceiling fan is equipped with reverse switch for downward or upward air flow.(see figure 14)

NOTE: Do not change the direction of rotation while the fan blades are in motion. To change direction,turn off the fan and wait for the blades to stop rotatingbefore setting the switch to the desired rotation direction,either forward orreverse.

Forward Function
On this setting, the fan will turn counter-clockwise to create a cooling effect. Use this function during warmer weather to circulate the hot air away from your living space.

Reverse Function
On this setting, the fan will turn clockwise. Use thisfunction during cooler weather to re-circulate warm air. (see figure 15)

Troubleshooting Guide

If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly,installation,or wiring.In some cases these installation errors may be mistaken for defects.If you experience any faults please check this troubleshooting guide.

1

|

If fan does not start.

| Check the main and branch circuit fuses or breakers.

Check the line wire connections to the fan and switch wire connections in the switch housing.

Check the battery in the remote control.

Ensure you are in the normal range of 10-20 feet.

2

|

If fan sounds noisy.

| Ensure all motor housing screws are snug.

Ensure the screws that attach the fan blade bracket to the motor hub are tight. Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.

Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.

If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light bulbs are also secure.

Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.

Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

3

|

If fan wobbles.

| Check that all blades are screwed firmly into blade holders. Check that all blade holders are tightened securely to motor.

Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box is mounted firmly to ceiling joist.

Most fan wobble problems are caused when blade levels are unequal.Check this level by selecting a point on the ceiling above the tip of one of the blades keeping measure within 1/8 in.Rotate the fan until the next blade is positioned for measurement.Repeat for each blade.If all blade levels are not equal you can adjust blade levels by the following procedure.To adjust a blade tip down insert a washer(not supplied)between the blade and blade holder at the screw closest to the motor.To adjust a blade tip up insert washer(not supplied)between the blade and blade holder at the two screws farthest from the motor.

If blade wobble is still noticeable interchanging two adjacent (side by side)blades can redistribute the weight and possibly result in smoother operation.

4

|

If light does not work.

| Check blue wire from fan to make sure it is connected to hot wire from the house. Check for loose or disconnected wires in fan switch housing.

Check for loose or disconnected wires in light kit.

Check for faulty light bulbs.CAUTION:Make sure main power is turned off before entering switch housing.

If the fan light shuts off shortly after being switched on it may be due to excessive current demand.Turn off power to the fan and replace the light bulbs with lower wattage bulbs.Turn on power to the fan using the pull chain,wall switch,or remote control (whichever is installed on the particular fan).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>