hykolity WHB-0108 Wood Burning Fire Pit with Grill User Manual

User’s Manual
26″ Wood Burning Fire Pit w/grill
WHB-0108For Outdoor Use Only

PACKAGE CONTENTS

Hardware Pack

SAFETY INFORMATION

**** Please read and understand this entire manual before attempting to assemble, operate or install the product.

• This item is for outdoor use only, and shall NOT be used in a building, garage or any other enclosed area. TOXIC carbon monoxide(CO) fumes can accumulate and cause asphyxiation or death.

• This fire pit is NOT for commercial use.

• This fire pit is NOT to be operated by children.

• This fire pit is NOT to be used in or on boats or recreational vehicles.

• Always use in accordance with all applicable local, state and national codes. Contact your local fire department for details on outdoor burning.

• The use of alcohol, prescription or non-prescription drugs may impair the consumer’s ability to properly assemble or safely operate this fire pit.

• This fire pit is for use with dry, seasoned hardwood. It will burn hotter, more completely and create less smoke.

• DO NOT burn lump charcoal, manufactured logs, driftwood, trash, leaves, papers, cardboard, plywood, painted or stained or pressure treated wood. Avoid using softwoods such as pine or cedar that can throw sparks.

• DO NOT alter this fire pit in any manner.

• DO NOT use this fire pit until it is COMPLETELY assembled and all parts are securely fastened and tightened.

• DO NOT store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.

• DO NOT store or use an LP gas cylinder within 10 feet (3.05 m) of this fire pit while it is in operation. The fire pit should be placed no closer than 24 inch from walls during use.

• DO NOT use this fire pit near automobiles, trucks, vans or recreational vehicles.

• Keep outdoor area clean and free from combustible materials, gasoline and other flammable liquids.

• DO NOT use this fire pit under an overhead or near any unprotected combustible constructions. Avoid using near or under overhanging trees and shrubs.

• Always use this fire pit on a hard level noncombustible surface such as concrete, rock or stone. An asphalt or blacktop surface may not be acceptable for this purpose. DO NOT use on wooden decks.

• Always empty this fire pit before each use.

• DO NOT wear flammable or loose clothing when operating this fire pit.

• DO NOT use in windy conditions.

• DO NOT use gasoline, kerosene, diesel fuel, lighter fluid to start or relight fires.

• Keep all electrical cords away from a hot fire pit.

• All surfaces of this fire pit are hot when in operation. To avoid burns, do NOT touch fire pit until it has completely cooled unless you are wearing protective gear (potholders, gloves, BBQ mittens, hot pads , etc). Never touch ashes to start or coals to see if they are hot.

• DO NOT attempt to move or store this fire pit until ashes and coals are completely extinguished.

• DO NOT remove ashes or coals until they are completely and extinguished.

• Use heat-resistant gloves or hot pads when contacting handles.

• Use long, sturdy fire pit tools when adding or moving logs.

• DO NOT place wood directly into bottom of the fire pit. Place wood only on the center of the fire bowl.

• DO NOT overload the fire pit. DO NOT add additional firewood until the fire burns down.
  NOTICE: If any portion of the bowl of this fire pit are glowing red, it is overloaded.

• DO NOT lean over this fire pit when lighting or when in use.

• DO NOT place hot pit tools onto combustible surface such as grass, wooden deck or furniture.

• Avoid breathing smoke from the fire and avoid getting it into your eyes.

• This fire pit should be thoroughly inspected and cleaned on a regular basis.

• After a period of storage and/or non-use, check for signs of damage and creosote build-up. DO NOT operate until necessary repairs and/or clean up is executed.

• Death, serious injury or damage to property may occur if the above is not followed Exactly

ASSEMBLY INSTRUCTION

Tools Required:
Phillips screwdriver (not included)
Wrench (included).
STEP 1.
Thread the Mesh Cover Handle through the Mesh Cover Lid and the Mesh Cover. Secure the M6 nut(B) with the provided M6 wrench(C) .Tighten the screws .DO NOT cross thread.

STEP 2.
Assemble the Side Panel with 8 pieces of M6x10 screw(A). Tighten the screws .DO NOT cross thread.

STEP 3.
Flip the assembled side panels upside down. Install the Bowl tray with 8 pieces of M6x10mm screw(A). Tighten the screws .DO NOT cross thread.

STEP 4.
Attach the assembled fire bowl onto the base with 8 pieces of M6x10 screw(A). Tighten the screws .DO NOT cross thread.

STEP 5.
For BBQ use, remove the mesh cover, and place the Cook Grate into the bowl .Place back the mesh cover when a fire is lit and food is settled on the cooking grate. Keep the poker near the fire pit for use as needed.

STEP 6.
For fire pit use, remove the cook grate. Place the mesh cover on the fire bowl. Place the poker aside the fire pit for use as needed.

CARE & MAINTENANCE

Lighting

1. Make sure there is only a small amount of ash in the bottom of the bowl.
2. Place a layer of dry kindling or a natural fire-starter onto the center of the fire bowl.
3. Place above that a layer of dry seasoned hardwood that is no more than 3/4 the length of the bowl diameter.
4. Use a match to light kindling or fire-starter.

Tending the Fire
You may need to shift and/or add logs for an ideal experience.
DO NOT place hot fire pit tools onto combustible surfaces such as grass, wooden deck or furniture.

1. While using a long handled fire pit tool, shift coals and logs to allow additional airflow.
2. DO NOT add gasoline, kerosene, diesel fuel, lighter fluid or alcohol to relight or enhance an existing fire.
3. Wait until glowing coals have developed before adding any additional wood. If additional wood is required, place wood on top coals, be careful not to shift ashes.

Extinguishing
Allow fire to burn itself out.
DO NOT use water to extinguish as this is dangerous and can cause damage to this outdoor fire pit.
Inspecting
This fire pit should be inspected on a regular basis to ensure product safety and longer product life.
DO NOT attempt to inspect this fire pit until the fire is COMPLETELY out and cool to the touch.

1. Check components for any signs of damage or rust.
2. If damage to any component is detected, do NOT operate until repairs are executed.

Cleaning
This fire pit should be cleaned on a regular basis to promote safer experiences and longer product life.
Note: After repeated use, a slight discoloration of the finish may occur.
DO NOT attempt to clean this fire pit until the fire is COMPLETELY out and cool to the touch.
DO NOT use oven cleaner or abrasive cleaners as they will damage this product.
DO NOT clean any part of this fire pit in a self cleaning oven as it may damage the finish.

1. Wipe exterior surfaces with a mild dishwashing detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.
3. Rinse and clean with water.
4. Remove built-up creosote from components with a chimney cleaning product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>