BOSCH W11692818 High Efficiency Front Load Washer User Guide

BOSCH W11692818 High Efficiency Front Load Washer

Product Information

Specifications:

• Type : High-Efficiency Front Load Washer
• Model : [Insert Model Number]
• Manufacturer : [Insert Manufacturer]

Product Usage Instructions

Removing Shipping Bolts
Before setting up the washer, ensure to remove any shipping bolts that may be in place to prevent damage during operation.

Connecting Water/Securing Drain Hose

1. Connect new inlet hoses to faucets and insert new hose washers into each end of the hoses.
2. Connect the inlet hoses to the washer and check for leaks. Make sure both hot and cold water hoses are connected to the correct faucets.
3. Ensure water faucets are turned on fully before using the washer for the first time.
4. Install and secure the drain hose properly to avoid leaks or blockages. Do not seal the drain hose or insert more than 4.5 inches into the drainpipe.

Setting Up the Washer

1. Clearwater lines before use.
2. Make sure the washer is level as per the installation instructions.
3. Run a wash cycle to verify correct operation and check for leaks at faucets and inlet hoses.

Electrical Safety
Plug the washer into a grounded 3-prong outlet and do not use adapters or extension cords to prevent electrical shock hazards.

WARNING
Fire Hazard

• Never place items in the washer that are dampened with gasoline or other flammable fluids.
• No washer can completely remove oil.
• Do not dry anything that has ever had any type of oil on it (including cooking oils).
• Doing so can result in death, explosion, or fire.

REMOVING SHIPPING BOLTS

Position the washer so that the rear is within approximately 3 ft (914 mm) of its final location. Keep the washer in the upright position; using a 1/2″ wrench, loosen each of the four shipping bolts on the rear panel. Once each bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer and store them in  a location for use if the unit needs to be moved at a later date.
IMPORTANT : If the washer is to be transported at a later date, call your local service center for new transport bolts if the original set is misplaced. Machine must be transported in the upright position. To avoid structural or suspension damage to your washer, it must be properly set up for relocation by a certified technician. Close the bolt holes with the four transport bolt hole plugs.\

KEY AND COIN BOX

LOCATION OF KEY
Coin box key (shown) comes taped to coin box lock. Document the key code (engraved on coin box key) in a safe place. If key is lost, contact 1-800-221-0982 X200 or X154 for replacement (not covered by warranty). Have key code handy; otherwise, locksmith will have to drill out coin box and replacement coin box (part no. W11190039) will have to be installed. Applies only to select models.

CONNECTING WATER/SECURING DRAIN HOSE

1. CONNECT NEW INLET HOSES TO FAUCETS
   Insert new hose washers (in separate bag) into each end of inlet hoses. Firmly seat washers into couplings. Do not overtighten or use tape or sealants when attaching to faucets.

2. CLEARWATER LINES
   Make sure that both hot and cold water hoses are connected to the correct faucets. The washer will not operate unless both hoses are connected.

3. CONNECT INLET HOSES TO WASHER AND CHECK FOR LEAKS
   Do not overtighten or use tape or sealants when attaching to washer. Turn on faucets and check for leaks at both ends of hoses.

4. IMPORTANT:
   Make sure that water faucets are turned on fully before using the washer for the first time. If there is no/low water pressure to the washer, the display will scroll “lo h2O”. To clear, open and close the washer door.

5. Install and secure the drain hose in a manner that will avoid it coming out of or leaking from the plumbing/drain. Do not seal or put more than 4.5″ (114 mm) of the drain hose into drainpipe or standpipe.

SETTING UP THE WASHER

WARNING
Electrical Shock Hazard

• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

Plug in washer or connect power. “ SYNC ” will be displayed for less than 1 minute.
Make sure that the washer is level (see the “Level Washer” section in the Installation Instructions). Run a wash cycle to verify that the washer is working correctly and has no leaks at faucets and inlet hoses.

CHANGING COIN DROP PRICING (Applies only to select models)

Refer to Installation Instructions for detailed instructions located in the washer.

NOTE : Coin box needs to be emptied frequently to avoid jams and damage.

For coin drop use, match the wash price on the display to the number of coin 1s for Regular cycle price and the value of coin 1. See the Installation Instructions for programming details.

For a suggested setup, see the “User & Set-Up Instructions” section of the Installation Instructions.
NOTE
To minimize the potential of oversudsing, follow this recommended setup:
Add a two-minute prewash length (see the “User & Set-Up Instructions” section of the Installation Instructions).

IMPORTANT WASH TIPS

• Shake out clothing prior to loading.
• Zip all zippers.
• Use the recommended amount of HE detergent.
• If a detergent pod is used, toss it into the wash drum not into the dispenser.
• Use chlorine bleach only.
• Fabric softener must be diluted.

NOTE : The washer remains locked for the entire wash cycle.

FAQ

Q: What should I do if there is low water pressure on the washer?
A: If there is low water pressure, the display will show ‘lo h2O.’ To resolve this, open and close the washer door.

Q: How do I change coin drop pricing on select models?
A: Refer to the Installation Instructions for detailed steps on changing coin drop pricing. Remember to empty the coin box frequently to prevent jams and damage.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>