ZHONGYANG ZYLY-F Bluetooth Module User Manual
- May 15, 2024
- ZHONGYANG
Table of Contents
ZHONGYANG ZYLY-F Bluetooth Module
Specifications
- Model: Z YLY-F Jiangxi Zhongyang Electrical Co. Ltd.
- Chip: AC6956C by Zhuhai Jerry Technology Co., Ltd.
- Bluetooth Version: V5.1+BR+EDR+BLE
- Operating Voltage: 2.2-5.5V
- Bus Interface: UART
- Frequency: 2402-2480MHz
- Dimensions: 21.59mm x 32.4mm x 10mm
Product Usage Instructions
Music Bluetooth Connection
To connect the music Bluetooth for classic music playback:
- Open the Bluetooth option in your phone settings.
- Search for the music Bluetooth named SYMK and select it to establish a connection.
- The music played on the phone will be transmitted to the musicBluetooth output.
BLE Bluetooth Connection (Example: Zwift APP)
- Find and launch the Zwift APP on your phone.
- Login to your account within the Zwift APP.
- Select the treadmill Bluetooth pairing option.
- Click “RUN” to enter the running interface.
- Start the treadmill and adjust the speed accordingly.
- End the running session within the app when finished.
Version’s history
| Date | Version | Remarks |
|---|---|---|
| 2024/1/23 | 1.0 | |
| 2024/2/27 | 1.1 | Add warning |
Module overview
-
Chip introduction
The module uses the AC6956C chip of Zhuhai Jerry Technology Co., Ltd. as the core. It is a high-performance 32-bit DSP that supports hardware Float Point
Unit(FPU) that supports a maximum operating frequency of 2402-24 80MHz. -
Main features
-
Bluetooth version : V5.1+BR+EDR+BLE Specification
-
Operating Voltage: 2.2-5.5V
-
Bus interface: UART
-
Scope of application
-
Classic Music Bluetooth
-
Bluetooth to serial port products: data transmission connection between treadmill and Kinomap APP or Zwift APP
-
Interface Protocol UART
-
Pin Definition
Dimensions: 21.59mm x 32.4mm x 10mm
| PIN No. | Name | Function | Description |
|---|---|---|---|
| E-1 | GND | Power ground | |
| E-2 | DP | USB D+ | |
| --- | --- | --- | --- |
| E-3 | DM | USB D- | |
| E-4 | VDD | Power supply | +5V |
| E-5 | RX | Serial port reception | BLE module data reception |
| E-6 | TX | Serial port sending | BLE module data sending |
| E-7 | LINR | Right channel input | |
| E-8 | LINL | Left channel input | |
| E-9 | ADKEY | Analog key detection | |
| E-10 | DACR | Right channel output | |
| E-11 | DACL | Left channel output | |
| E-12 | AGND | Analog ground | |
| J-1 | TX | Serial port sending | BLE module data sending |
| J-2 | RX | Serial port reception | BLE module data reception |
| J-3 | GND | Power ground | |
| J-4 | VDD | Power supply | +5V |
| J-5 | PWM | PWM output | Bluetooth heart rate |
| J-6 | ADKEY | Analog key detection | |
| J-7 | NULL | NULL | NC |
| J-8 | AGND | Analog ground | |
| J-9 | DACL | Left channel output | |
| J-10 | DACR | Right channel output |
Music bluetooth connection
Open the Bluetooth option in the phone settings, search for the music
Bluetooth that displays SYMK, and click on the connection successfully. The
music played on the phone will be transferred to the music Bluetooth output.
BLE Bluetooth connection an example: Zwift APP
- Find the Zwift APP on your phone
- Run Zwift APP
- Select account login
- Select treadmill Bluetooth pairing
- Click “RUN” to enter the running interface
- After starting the treadmill, adjust the speed
- End running on the app
Appendix warning
Federal Communication Commission Statement (FCC, U.S.)
This equipment has been tested and found to comply with the limits for a Class
B digital device, under Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used by the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
IMPORTANT NOTES
Co-location warning
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
OEM integration instructions
- This device is intended only for OEM integrators under the following conditions:
- The transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the external antenna(s) that have been originally tested and certified with this module.
- As long as the conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
Validity of using the module certification
If these conditions cannot be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC authorization for this
module in combination with the host equipment is no longer considered valid
and the FCC ID of the module cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the
end product (including the transmitter) and obtaining a separate FCC
authorization.
End product labeling
The end product must be labeled in a visible area with the following:
“Contains Transmitter Module FCC ID: 2AXTX-ZYLY-F”.
Information that must be placed in the end user manual
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product that integrates this module. The end user manual shall include all
required regulatory information/warnings as shown in this manual. Integration
instructions for host product manufacturers according to KDB 996369 D03 OEM
Manual v01
FAQ
- Q: What is the main feature of the Bluetooth module?
- A: The main features include Bluetooth version V5.1 with support for BR, EDR, and BLE specifications, an operating voltage range of 2.2-5.5V, and a UART bus interface.
- Q: What is the scope of application for this Bluetoothmodule?
- A: The module is suitable for classic music Bluetooth connections and Bluetooth to serial port products for data transmission between devices like treadmills and apps such as Kinomap or Zwift.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>