PARSEC PRO9K K9 PRO Series Low Profile LTE Antennas Instruction Manual

PARSEC PRO9K K9 PRO Series Low Profile LTE Antennas

The K9 PRO Series antennas are rugged, high performance, 5G, CAT18 (600 MHz to 6 GHz) antennas, available with up to 4×4 MIMO LTE, up to 4×4 MIMO WiFi, CBRS, LTE LAA, and GPS/GNSS. The K9 antennas are IP67- rated antennas and perfect for mobile and fixed wireless applications.

OPTIONAL ACCESSORIES

• PTA0257:  1.5 inch Star Lock Washer
• PTA0347 : Heavy Duty Hardware Kit ( Nut, Lock Washer and Flat Washer.

REQUIRED TOOLS

• Hammer / Rubber Mallet
• Drill and 0.1 in Drill Bit
• Phillips Screwdriver
• 1.5 in Hole Saw
• SMA Wrench

Mounting Options

Step 1

Select a mounting location where there is no obstructions within a radius of 24in. and is easily accessible.

Step 2

Select one of the mounting options below, depending on your use.

Roof Mount Included

K9 antennas can be mounted on an automobile roof or any flat surface using the hardware provided with it.

Magnetic Mount

Optional Part Number: PTA0329
For temporary use. K9 antennas can be mounted on any ferrous metal surface using magnetic mount brackets.

Pole Mount

Optional Part Number: PTA0149H
Antennas can be mounted on a pole with an optional bracket.

Preparing the Hole

Step 1

After selecting the location to mount the Antenna, mask the mounting location to avoid paint damage. Then mark the hole center with ink or scribed cross hairs.

Step 2

Use a center punch to make a dimple on the marked location to avoid drill bits from walking across the sheet metal. Then use a Twist drill of diameter about 0.1 and drill a pilot hole. Then using a 1.5 diameter sheet metal hole saw, drill the hole.

Step 3

The hole saw will cut the required diameter hole with less risk of stretching and distorting the vehicle surface. Clean up any metal shavings from the hole cutting process.

Step 4

Clean up any metal shavings from the hole cutting process.

Mounting the Antenna

Step 1

Feed the coaxial cables from the antenna through the hole from the outside surface to the inside surface and thread the entire length of the cable through the hole.

Step 2

Clean debris off the vehicle surface and then mark the desired antenna orientation by placing the antenna flat on the vehicle surface.

Step 3

Lift the antenna and remove the protective backing from the underside of the antenna and place the antenna back in the desired position. Apply downward pressure on the antenna to stick it to the panel.

Step 4

To avoid the gap between the antenna and panel, it is reccomenended to use neutral cure silicon sealant around the base of the mounting boot to fully compress the antenna to the mounting panel.

Step 5

A split flat washer and a split hex nut are provided in the kit for easy installation. Star washer is optional and not supplied. On the inside of the vehicle, thread the flat washer over the cable, followed by star washer (if applicable) and then hex nut.

Slide the washers and nut to the threaded flange of the antenna and tighten the hex nut until antenna compresses flat with the surface of the vehicle.

For best performance avoid bending the cable under 0.5 radius. And make sure the antenna is mounted in correct direction and tighten the mounting hardware. And waterproof the RF connectors using electric tape or a heat shrink tube if required.

Magnetic Mount Instructions PTA0329

Step 1

Choose a mounting location. The magnetic mount can be mounted on ferromagnetic metals like iron, steel, nickel etc but not aluminum, copper etc.

Step 2

Make sure all of the magnets stick firmly to the base. If the surface is a curve adjust the magnets heights using washer.

Step 3

Make sure the antenna is mounted at least 18 inches or as far as possible from the other roof mounted items like antennas, light bars etc. to avoid any de- tuning or interference issues.

Routing the Cables

Step 1

Route the cable from the antenna to the router by maintaining a minimum bend radius of 0.5in. Avoid sharp bends. Run the cables adjacent to existing wiring.

Step 2

Waterproof the RF connectors using electrical tape or a heat shrink tube, if required.

Cable Connection Instructions

Note
SMA connectors have a maximum torque of 3-5 inch lbs.

Step 1

Clean the connector such that there is no dust in the terminals.

Step 2

Connect the cables from the antenna to the designated connector on the antenna as shown in the table below.

For best MIMO performance use the following in pairs

• LTE1 & LTE2
• LTE3 & LTE4
• WIFI 1 & WIFI 2
• WIFI 3 & WIFI 4

Commission and Testing

Check Coaxial Cables

Check each coaxial cable connector and confirm it can’t be easily unscrewed with two fingers. Visually inspect coaxial cable run for proper mechanical support.

Confirm Connection to Cellular Network

Use a cellular device’s built in diagnostics to confirm t0he RSSI is better than -75dB. Confirm the cellular connection supports communications at required data rates. Connect the GPS / GNNS cable to the GPS / GNNS receiver and check for satelite acquisition. Connect the Cellular / LTE & WLAN cables or stow unused pigtails.

CAUTION
To comply with FCC RF Exposure requirements in section 1.1310 of the FCC Rules, antennas used with this device must be installed to provide a separation distance of at least 20 cm from all persons to satisfy RF exposure compliance. DO NOT Operate the transmitter when someone is within 24 inches of the antenna. Install antenna or mast assembly on a windy day Install the mast close to power lines as it can cause serious injuries or death.

WARNING
This document gives the detailed instructions to install an antenna to the best of our knowledge. This document if for general information only. It cannot be used as a warranty. Parsec Technologies, Inc. will not accept any liability for any damage caused by an antenna due to unknown variables.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>