EDA ED-HMI3010-101C Raspberry Pi Technology Platform User Guide
- May 15, 2024
- EDA
Table of Contents
EDA ED-HMI3010-101C Raspberry Pi Technology Platform
Specifications:
- Product Model: ED-HMI3010-101C
- Manufacturer: EDA Technology Co., LTD
- Application: IOT, industrial control, automation, green energy, artificial intelligence
- Supported Platform: Raspberry Pi
- Contact Information:
- Address: Room 301, Building 24, No.1661 Jialuo Highway, Jiading District, Shanghai
- Email: sales@edatec.cn
- Phone: +86-18217351262
- Website: https://www.edatec.cn
- Technical Support:
- Email: support@edatec.cn
- Phone: +86-18627838895
- Wechat: zzw_1998-
Product Usage Instructions
Installation :
To install the ED-HMI3010-101C, follow these steps:
- Ensure the environment meets design specifications.
- Fix the equipment securely to prevent falls.
Startup:
To start using the product:
- Refer to the user manual for detailed startup instructions.
Configuration :
Configure the product by following these steps:
- Refer to the application guide for configuration details.
Maintenance
To maintain the product:
- Avoid using liquid cleaning equipment.
- Keep the product away from liquids and flammable materials.
FAQ:
-
Q: What should I do if the product fails to start?
A: If the product fails to start, please check the power source and connections first. Refer to the user manual for troubleshooting steps. -
Q: Can I modify the equipment for customization?
A: It is not recommended to modify the equipment without permission as it may lead to equipment failure and void the warranty. -
Q: How do I get technical support?
A: For technical support, you can contact us through email at support@edatec.cn or call +86-18627838895.
ED-HMI3010-101C
Application Guide
EDA Technology Co., LTD December 2023
Contact Us
- Thank you very much for purchasing and using our products, and we will serve you wholeheartedly.
- As one of the global design partners of Raspberry Pi, we are committed to providing hardware solutions for IOT, industrial control, automation, green energy and artificial intelligence based on Raspberry Pi technology platform.
- You can contact us in the following ways:
- EDA Technology Co.,LTD
- Address: Room 301, Building 24, No.1661 Jialuo Highway, Jiading District, Shanghai
- Mail: sales@edatec.cn
- Phone: +86-18217351262
- Website: https://www.edatec.cn
- Technical Support:
- Mail: support@edatec.cn
- Phone: +86-18627838895
- Wechat: zzw_1998-
Copyright Statement
- ED-HMI3010-101C and its related intellectual property rights are owned by EDA Technology Co.,LTD.
- EDA Technology Co.,LTD owns the copyright of this document and reserves all rights. Without the written permission of EDA Technology Co.,LTD, no part of this document may be modified, distributed or copied in any way or form.
Disclaimer
EDA Technology Co.,LTD does not guarantee that the information in this manual is up to date, correct, complete or of high quality. EDA Technology Co.,LTD also does not guarantee the further use of this information. If the material or non-material related losses are caused by using or not using the information in this manual, or by using incorrect or incomplete information, as long as it is not proved that it is the intention or negligence of EDA Technology Co.,LTD, the liability claim for EDA Technology Co.,LTD can be exempted. EDA Technology Co.,LTD expressly reserves the right to modify or supplement the contents or part of this manual without special notice.
Foreword
Related Manuals
All kinds of product documents contained in the product are shown in the
following table, and users can choose to view the corresponding documents
according to their needs.
| Documents | Instruction |
|---|---|
| ED-HMI3010-101C Datasheet | This document introduces the product features, |
software and hardware specifications, dimensions and ordering codes of ED-
HMI3010-101C to help users understand the overall system parameters of the
products.
ED-HMI3010-101C User Manual| This document introduces the appearance,
installation, startup and configuration of ED-HMI3010-101C to help users use
the product better.
ED-HMI3010-101C Application Guide| This document introduces the OS download,
SD flashing and open/close device case of ED-HMI3010-101C to help users use
the product better.
Users can visit the following website for more information: https://www.edatec.cn
Reader Scope
This manual is applicable to the following readers:
- Mechanical Engineer
- Electrical Engineer
- Software Engineer
- System Engineer
Related Agreement
Symbolic Convention
| Symbolic | Instruction |
|---|---|
| **** | Prompt symbols, indicating important features or operations. |
| **** | Notice symbols, which may cause personal injury, system damage, or |
signal interruption/loss.
****| Warning symbols, which may cause great harm to people.
Safety Instructions
- This product should be used in an environment that meets the requirements of design specifications, otherwise it may cause failure, and functional abnormality or component damage caused by non-compliance with relevant regulations are not within the product quality assurance scope.
- Our company will not bear any legal responsibility for personal safety accidents and property losses caused by illegal operation of products.
- Please do not modify the equipment without permission, which may cause equipment failure.
- When installing equipment, it is necessary to fix the equipment to prevent it from falling.
- If the equipment is equipped with an antenna, please keep a distance of at least 20cm from the equipment during use.
- Do not use liquid cleaning equipment, and keep away from liquids and flammable materials.
- This product is only supported for indoor use.
Install OS
This chapter introduces how to download OS file and flash SD card.
- Download OS File
- Flash SD Card
Download OS File
If the operating system is damaged during use, you need to re-download the
latest version of the system image and flash it.
Flash SD Card
ED-HMI3010-101C starts the system from the SD card by default. If you need to
flash the latest system, you need to flash the system image to the SD card. It
is recommended to use the official Raspberry Pi flashing tool, and the
download path is as follows:
Raspberry Pi Imager :
https://downloads.raspberrypi.org/imager/imager_latest.exe
Preparation:
- The download and installation of the flashing tool to the computer has been completed.
- A card reader has been prepared.
- The OS file to be flashed has been obtained.
- The device case has been opened and the SD card of ED-HMI3010-101C has been obtained. For detailed operations, please refer 2.1 Open Device Case to 2.2 Pull Out SD Card and.
Steps:
The steps are described using Windows system as an example.
- Insert the SD card into the card reader, and then insert the card reader into the USB port of PC.
- Open Raspberry Pi Imager, select “CHOOSE OS” and select “Use Custom ” in the pop-up pane.
- According to the prompt, select the downloaded OS file under the user-defined path and return to the main interface.
- Click “CHOOSE STORAGE”, select the SD card of ED-HMI3010-101C in the “Storage” interface, and return to the main interface.
- Click “WRITE” and select “Yes” in the pop-up prompt box to start writing the OS.
- After the OS writing is completed, the file will be verified.
- After the file verification is completed, the prompt box “Write Successful” pops up, and click “CONTINUE” to finish flashing SD card.
- Close Raspberry Pi Imager, remove the card reader
- Insert the SD card into the Raspberry Pi 5 and close the device case (for detailed operations, please refer to 2.3 Insert SD Card and 2.4 Close Device Case), and then power on again.
Open and Close Case
This chapter introduces the operations for opening/closing the device case and inserting/removing the SD card.
- Open Device Case
- Pull Out SD Card
- Insert SD Card
- Close Device Case
Open Device Case
Preparation :
A cross screwdriver has been prepared.
Steps:
Use a screwdriver to loosen the 4 M3 screws on the ED-HMI3010-101C metal
case counterclockwise, and remove the metal case, as shown in the figure
below. 
Pull Out SD Card
Preparation :
- The device case has been open.
- A pair of tweezers is ready.
Steps:
- Find the location of the SD card, as shown in the figure below.
- Use tweezers to hold the SD card and pull it out.
Insert SD Card
Preparation:
- The device case has been open.
- SD card has been pulled out.
Steps:
- Find the location of the SD card slot, as shown below the red box.
- Insert the SD card into the corresponding card slot with the contact side facing up, making sure it will not fall out.
Close Device Case
-
Preparation :
A cross screwdriver has been prepared. -
Steps:
Cover the case, insert 4 M3 screws, and tighten clockwise to secure the case.
ED-HMI3010-101C Application Guide
Documents / Resources
| EDA
ED-HMI3010-101C Raspberry Pi Technology
Platform
[pdf] User Guide
ED-HMI3010-101C Raspberry Pi Technology Platform, ED-HMI3010-101C, Raspberry
Pi Technology Platform, Pi Technology Platform, Technology Platform
---|---