SonoFF V1.3 Extreme Zigbee Smart Switch User Guide
- May 15, 2024
- SonOFF
Table of Contents
ZBMINI Extreme
Quick Guide V1.3 Zigbee Smart Switch
(No Neutral Required)
Power off
Please install and maintain the device by a professional electrician.
To avoid electric shock hazard, do not operate any connection or contact the
terminal connector while the device is powered on!
Wiring instruction
-
It is prohibited to connect S1 and S2 terminals to the neutral or ground wire, in order to avoid damaging the equipmentand causing danger.
-
Make sure all wires are connected correctly.
-
Supported switches are rocker switch and push button and factory default by supporting rocker switch.
Method of change the switch type: short press the button 3 times until the green indicator flashes 3 times quickly, now you change the switch type successfully. -
The device will remain in the off state and cannot be controlled by the device’s button or external switch when it is in Pairing mode.
Pair with eWeLink App
Download the eWelink App
Pair SONOFF ZB Bridge to your eWeLink account
Power on
After powering on, the device will enter the pairing mode defaulted during the
first use and the LED signal indicator will “flash slowly”.
The device will exit the pairing mode if you do not operate it within 3
minutes. When you want to enter the pairing mode again, long press the button
on the device for 5 seconds until the signal light “flashes slowly” and
release.
Add ZBMINI Extreme to the ZB Bridge
Open eWeLink App, tap “Add” icon on the ZB Bridge interface, then wait to looking for and add the sub-devices.
Pair with Amazon Echo
Download the latest Amazon Alexa App and pair it with Amazon Echo with built- in Zigbee hub.
Power on ZBMINI Extreme, then it defaulted to enter the pairing mode and the
LED signal indicator “flashes slowly”.
Ask the Alexa Echo to discover the devices automatically by saying “Alexa,
discover my devices’.
If failed to pair within 3mins, ZBMINI Extreme will exit the pairing mode.
Long press the button on ZBMINI Extreme for 5s to make it enter the pairing
mode if you need to pair again.
https://sonoff.tech/usermanuals
Scanthe QRcode or visit the website to learn about the detailed user manual and help.
FCC compliance statement
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet ona circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
For CE Frequency
Operation frequency Range
Zigbee: 2405-2480MHz
RF output Power
Zigbee: <13dBm
ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence- exempt
RSS(s). Operation is subject to the following two conditions: (1)This device
may not cause interference.(2)This device must accept any interference,
including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003(B).
This device complies with RSS-247 of Industry Canada.
Operation is subject to the condition that this device does not cause harmful
interference.
WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic
equipment (WEEE as in directive 2012/19/EU) which should not be mixed with
unsorted household waste. Instead, you should protect human health and the
environment by handing over your waste equipment to a designated collection
point for the recycling of waste electrical and electronic equipment,
appointed by the government or local authorities.
Correct disposal and recycling will help prevent potential negative
consequences to the environment and human health. Please contact the installer
or local authorities for more information about the location as well as terms
and conditions of such collection points.
To ensure the safety of your electrical installation, it’s essential either a
Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit
Breaker (RCBO) with an electrical rating of 6A has been installed before the
ZBMINIL2.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type ZBMINIL2 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: https://sonoff.tech/compliance/
Shenzhen Sonoff Technologies Co., Ltd.
3F & 6F, Bld A, No. 663, Bulong Rd, Shenzhen, GD, China MADE IN CHINA
ZIP code: 518000 Website: sonoff.tech Service email:
support@itead.cc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>