Goodflys GF-H1Pro Smart Helmet User Guide
- May 15, 2024
- Goodflys
Table of Contents
- Goodflys GF-H1Pro Smart Helmet
- Product Information
- Product Usage Instructions
- Frequently Asked Questions
- Introduction
- Packing List.
- Wearing Instructions
- Operating instructions
- Attention
- Technical Specifications
- Electronic Functions Troubleshooting
- FCC
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Goodflys GF-H1Pro Smart Helmet
Product Information
Specifications:
- FCC ID: ABGF-HPRO
- Compliance: Part of FCC Rules
- Conditions: Must not cause harmful interference, must accept any received interference
Product Usage Instructions
Initial Setup:
Before using the device, ensure it is charged or connected to a power source. Follow the manufacturer’s instructions for initial setup.
Power On/Off:
To power on the device, press and hold the power button until the indicator light turns on. To power off, repeat the same process until the indicator light goes off.
Connectivity:
For wireless connectivity, enable Bluetooth on your device and pair it with the product. For wired connections, use the provided cable to connect to compatible devices.
Operation:
Follow the user manual for specific operations related to the product. Use the controls/buttons provided to navigate through settings and functionalities.
Maintenance:
Regularly clean the device using a soft, dry cloth. Avoid using harsh chemicals or solvents that may damage the product’s surface.
Frequently Asked Questions
Q: What should I do if the device is not pairing with my smartphone?
A: Make sure the device is in pairing mode and within range of the smartphone. Restart both devices and try pairing again. If issues persist, refer to the troubleshooting section in the user manual.
Q: How long does the battery last on a full charge?
A: The battery life varies based on usage, but on average, it can last up to X hours on a full charge. It is recommended to fully charge the device before extended use.
Introduction
Note: This diagram is for reference only. If the actual product appears different from the diagram, the real prod cut shall prevail.
Packing List.
- Helmetx 1
- Quick Start Guide x 1
- Remote Controller x 1
- Type-C USB Charging Cable x 1
Wearing Instructions
Operating instructions
(Please charge before use)
Instructions of Buttons
Note: This button got 8 functions, please read below instructions carefully before use.
Charging
Open the soft rubber lid with “Type-C”, USB charging cable will be seen. Insert a USB cable into it. Charging starts when red light indicator appeared and charging completed when red light indicator disappeared(charge no less than 3hrs.).
Connect to the Remote Controller
Hold press th ls button on remote controller, the green wlll be on, meaning it is turned on. And then quickly press this button 5 times to reset the remote controller and it will be connected with He met Automatically and will hear a voice saying “Remote connected” from the helmet after connected successfully.
Tips:
- To ensure the connection sigal stability, please try not to place your mobile phone right against your body.
- To connect remote controller to helmet first and then connect helmet to your smartphone via bluetooth, click the player button on remote control to activate the smartphone’s voice assistant service.
Connect to Helmet Bluetooth Player
(Tip:Once connected, it can control the music player as well as make or
receive a call. To ensure the stability of the connection, please try to
postion your smart phone in front of you).
When helmet is powered on, you will hear a voice saying “ready for
connection”. Remote controller will connect to the helmet automatically once
powered on. And will hear a voice saying” remote connected” after connected
successfully. Open your smart phone’s bluetooth, find lizvie helmet and pair
it. Will hear a voice saying “bluetooth connected” after connected
successfully.
Functions
- Bluetooth Player
- Noise Reduction System
- Remote Control
- LED Head light
- LED Taillights(L.C.R)
- Auto on/off
- One-Click Answer
Instructions for Use and Care
- Please choose the size which feels secure, comfortable and fits well on the head.
- Please adjust the straps position to be firm and comfortable.
- A helmet con not always protect against injury but can decrease risk of it only.
- Please discard the destroy the helmet if subjected to a severe impact.
- Clean only with mild soap and water, solvents may damage the helmet. Take good care of it, don’t strike the helmet.
- Please don’t modify or remove any of the original component parts of the helmet.
- Normally, valid for 3 years without impact.
Attention
- The helmet contains electronic parts inside. Please do not take a long ride in the rain although the helmet can prevent the rain from splashing.
- After the helmet gets wet in the rian, the water droplet might occur in the chimnry of LED Taillights. The water droplets will disapper when you put the helmet under the ventilation environment for 1-2 days.
- The helmet contains the battey. The battery capacity varies with temperature change. The battery life can decay when the helmet is used at low temperatures or below Zero degrees Celsius.
- For the battery lifetime, please charge the helmet completed everytime.
Technical Specifications
- Charging port: Type-C USB
- Electricity parameter: DC SV/lA
- Charging time: 3-4hrs
- Waterproof class: I PXS
- Battery Working Time: Max 60hrs (varies depending on)
- Storage Temperature: -l0°C~45°C
- Usage Temperature: 0°C~45°C
Electronic Functions Troubleshooting
During the usage, if any troubles occur, please press 5 times (power button) or long press 10 seconds to reset the device If the problems still can not be solved, please contact the after-sales service centre
FCC
FCC ID: 2A45 BGF-H1 PRO
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part ?? of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
~The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>