whynter BR-1211DS 121 Can Beverage Refrigerator with Digital Control and Internal Fan Instruction Manual

**whynter BR-1211DS 121 Can Beverage Refrigerator with Digital Control and Internal Fan Instruction Manual

**

Safety Precautions

APPLIANCE SAFETY
Your safety and the safety of others are very important to us.
To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions
This is the Safety Alert Symbol. This symbol alerts you to potential hazards that may result in serious injury. All safety messages will follow the Safety Alert Symbol and either the words” DANGER” or “WARNING”
Danger means that failure to heed this safety statement may result in severe injury or death.
Warning means that failure to heed this safety statement may result in extensive product damage, serious injury, or death.
Caution means that failure to heed this safety statement may result in minor or moderate injury, or property or equipment damage.

All safety messages will alert you to know what the potential hazard is, tell you how to reduce the chance of injury, and let you know what can happen if the instructions are not followed.

IMPORTANT SAFEGUIDES

Before the appliance is used, it must be properly positioned and installed as described in this manual, please read the manual carefully. To reduce the risk of fire,
electrical shock or injury when using the appliance, follow basic precaution, including the following:

• Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not use an extension cord.
• Do not use if the power supply cord is damaged. If damaged, it must be replaced by a qualified electrician.
• It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles that cannot be turned off by a switch or pull chain.
• Never clean appliance parts with flammable fluids or harsh chemicals. These fumes can create a fire hazard or explosion.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of the appliance or any other appliance.
• Before proceeding with cleaning and maintenance operations, make sure to unplug the appliance.
• Do not connect or disconnect the electric plug with wet hands.
• Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

• Use two or more people to move and install the appliance. Failure to do so can result in injury.
• When positioning the beverage refrigerator, ensure that there is at least a 4” clearance at the sides and a 6” clearance at the back.
• Please note that this is a freestanding appliance and should not be placed into a built-in space. Even with the recommended clearance, there may not be adequate airflow.
• It is recommended that you install the beverage refrigerator in a place where the ambient temperature is between (68°F- 78°F). This appliance must be installed in an area protected from the element, such as wind, rain, water spray or drips.
• The appliance should not be located next to ovens, grills or other sources of high heat.
• The appliance must be installed with all electrical connections in accordance with state and local codes.
• The fuse (or circuit breaker) size should be 15 amperes.
• It is important for the appliance to be leveled in order to work properly. For a stable installation, make sure the appliance is placed on a flat, level and solid surface.
• Ensure that the surface on which the appliance is placed is strong enough to hold the appliance and the items stored inside.
• This appliance is not intended for use by young children or physically-challenged persons without supervision/assistance. Young children must be supervised to ensure safety around this or any appliance.
• Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may damage or discolor the interior.
• Keep fingers out of the “pinch point” areas. Clearance between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.
• Close the beverage refrigerator immediately after putting in any items to keep the internal temperature relatively constant.
• Avoid placing any objects on top of the appliance.
• This is an electrical appliance, to avoid injury from electrical shock do not operate the unit with wet hands, while standing on a wet surface or while standing in water. Do not use outdoors or in wet conditions.
• When positioning or moving the appliance, ensure that it is not turned up side down or unleveled greater than 45°.
• Never pull the power cord to disconnect it from the outlet. Grasp the plug and pull it from the outlet.
• Never lift, carry or drag the appliance by the power cord.
• This appliance is designed for household, non-commercial use only. Any other use will void the warranty.
• Do not plug into the power outlet before set up is completed.
• Do not cut or remove the ground prong from the power cord.
• Do not move this appliance without emptying it and securing the door in a closed position.

Parts

1. Control Panel

| 8. Door Frame
---|---
2. Full Slide-Out Chrome Wire Shelves (4)

Half Slide-Out Chrome Wire

Shelf (1)

|

9. Cylinder Lock

3. Door Handle

|

10. Door Hinge

4. Wire Gate

| 11. Small Leveling Leg
5 Large Leveling Leg|

12. Drip Tray (Rear)

6. Door Hinge Cover

| 13. Power Cord (Rear)
7. Light and Internal Fan|

14. Door Keys

Product Features

FEATURES

• Capacity: 121 standard 12 oz. can
• Freestanding installation
• Stainless steel trimmed glass door with sleek black cabinet
• Touch screen control with temperature range from 34°F – 43°F (1°C – 6°C)
• Environmentally friendly refrigerant
• Tempered double pane glass for enhanced UV protection
• Soft interior LED lighting with on/off switch
• Internal fan-forced circulation for even temperature distribution throughout the cabinet
• Cylinder lock and two keys
• Fahrenheit and Celsius degree temperature indicators
• 4 full slide-out chrome wire shelves
• 1 half slide-out chrome wire shelf
• 1 wire gate

TECHNICAL DATA

Important Safety Instructions

WARNING| To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions:
---|---

• Read all instructions before using the appliance.
• DANGER or WARNING: An empty beverage refrigerator can be a hazardous for children or small pets. If disposing of the beverage refrigerator, remove gasket seals, latches, lids or the entire door from your unused appliance, or take other action to ensure the appliance is harmless.
• Never allow children to operate, play with, or crawl inside the appliance.
• Never clean appliance parts with flammable fluids or harsh chemicals. The fumes can create a fire hazard or explosion.
• Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.

BEFORE USING YOUR APPLIANCE

• Remove the exterior and interior packing.
• Clean the interior surface with lukewarm water using a soft cloth.
• Before connecting the appliance to the power source, let it stand upright for approximately 4 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.

INSTALLATION OF YOUR APPLIANCE

• WARNING: Do not store or install the appliance outdoors.
• CAUTION: This appliance is designed for storing and cooling beverages. Do not store perishable food, medicine or other medical products.
• Place your appliance on a hard and level floor that is strong enough to support it when it is fully loaded.
• To level your appliance, adjust the legs(1 large leveling leg and 1 small leveling leg under the door hinge) at the bottom of the appliance if needed.
• When positioning this freestanding beverage refrigerator, ensure that there is at least a 4” clearance at the sides and a 6” clearance at the back. Please note that this is a freestanding appliance and should not be placed into a built-in space. Even with the recommended clearance, there may not be adequate airflow.
• We do not recommend installing the appliance on carpet.
• Ensure that the condensation tube is directed into the drip tray located at the back of the unit to prevent leakage.
• Do not install the appliance near an oven or other heating source. Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. For best performance, do not install the appliance behind a cabinet door. Extreme cold ambient temperatures may also cause the appliance not to perform properly.
• Avoid locating the appliance in area that may be exposed to excessive moisture.
• Plug in the appliance into an exclusive, grounded wall power outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a qualified electrician or an authorized service center.

ELECTRICAL CONNECTION

This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury.
The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord.

EXTENSION CORD

Because of potential safety hazards, it is strongly recommended that you do not use an extension cord with this appliance. However, if you must use an extension cord, it is absolutely necessary that it be a UL/CULListed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes.

Operation and Controls

It is recommended you install the appliance in a place where the ambient temperature is between 72º- 78ºF / 23º-26ºC. If the ambient temperature is above or below recommended temperatures, the performance of the beverage refrigerator may be affected. For example, placing your appliance in extreme cold or hot conditions may cause interior temperatures to fluctuate.

CONTROL PANEL

SETTING THE TEMPERATURE

The temperature range can be set between 34ºF – 43ºF (1ºC – 6ºC). To set the desired temperature, press the button to lower the temperature or button to raise the temperature on the control panel. The temperature display will flash for 5 seconds indicating that the desired temperature is set and will revert back to its actual internal temperature.

NOTE:

1. The temperature inside the beverage refrigerator is dependent on the ambient temperature (room temperature).
2. The   cooling icon is illuminated when the cooling cycle unit is in operation. Once the unit reaches the set temperature, the cooling icon will shut off.

KEY LOCK
If in 2 minutes without touching any key, the controls will be locked automatically. To release the lock, touch the and buttons at the same time for at least 5 seconds. The key lock is released once the temperature display beeps and flashes.

INTERIOR LIGHT
You can turn on and off the interior light by pressing the Light button on the control panel.

ºC and ºF SELECTOR
To change temperature conversions, press the button to switch between temperature conversions.

LEVELING THE APPLIANCE
It is important for your appliance to be leveled in order to work properly. It can be raised or lowered by rotating each of the feet on the bottom of the machine. If you find that the surface is not level, rotate the feet until the appliance becomes level .You may need to make several adjustments to level it. We recommend using a carpenter’s level to check the machine.

NOTE: The Whynter BR-1211DS has 1 large leveling leg and 1 small leveling leg under the door hinge.

1. Place a carpenter’s level on top of the product to see if the appliance is level from front to back and side to side.
2. Adjust the height of the feet as follows: Turn the leveling feet to the right to lower that side of the refrigerator. Turn the leveling feet to the left to raise that side of the refrigerator.

Operation and Controls

INSTALLING STAINLESS STEEL HANDLES
This appliance includes stainless steel handles that are not required to operate this appliance. To install the handles please follow the below instructions:

1. The gaskets are easily displaced by hand, no tools are necessary.
2. Use a flat-head screwdriver to remove the two pre-installed decorative plugs from the back of doors. Some beverage refrigerators have no decorative plugs.
3. Install the handles tightly as shown with two screws, lock washers and flat washers provided. (DO NOT over tighten as this will cause damage to the handles and stainless steel door frames).
4. Replace the door gaskets to its original position.

WIRE SHELVES
NOTE: Do not cover any part of the wire shelves with aluminum foil or any other material that will prevent adequate air circulation within the cabinet.
This appliance is equipped with slide-out removable shelves. To prevent damage to the door gasket, make sure the door is opened completely before pulling the shelves out.

• For easy access of the beverage cans, you must pull the shelves approximately ⅓ out of the railing.
• The shelves are designed with an emergency stop to prevent them being removed too far when loaded.
• When removing the shelves out of the railing, make sure to remove all items first.
• To remove the shelves, pull the shelf forward until the notch aligns with the plastic post. Lift the shelf and continue to pull the shelf forward until it is completely removed from the internal compartment.

NORMAL SOUNDS
The unit is cooled by a compressor. The compressor pumps coolant through the cooling system, producing operating noise. Even when the compressor cuts out, noises caused by changes in temperature and pressure are unavoidable. Operating noise will be most audible immediately after the compressor comes on. It becomes quieter as the operating period continues.

The following noises are normal and occur from time to time:

• Gurgling sound, caused by the refrigerant flowing through the appliance’s coils,
• Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on.
• Cracking/popping sounds, resulting from the materials contraction and expansion due to temperature variations,
• Fan operating sound, to circulate the air within the beverage cabinet.
• Unusual noise is normally the result of improper installation.
• Where the unit is installed in open-plan kitchen or in partition walls, the level of operating noise will be heard more acutely. However, this is due to the surrounding architecture and not to the unit.

NOTE: An individual’s perception of noise is directly linked to the environment in which the unit is located, as well the specific type of models. Our appliances are in line with international standards for such appliance and in line with the latest technical developments. Please remember that the noise of the compressor and the coolant circulating in the system is unavoidable.

DEFROSTING AND VENTILATION
Your beverage refrigerator is designed with an automatic defrost system. During off-cycle, the evaporator behind the rear wall of the unit defrosts automatically. Condensation is collected in the drain at the back of the unit and flows through the drainage hole into the drip tray above the compressor. The heat is transferred from compressor and evaporates any condensation that has collected in the drip tray. Part of the remaining water within the beverage refrigerator is collected for humidity purposes.

NOTE: Frost may accumulate on the evaporator if the unit is repeatedly opened in a high heat or high humidity location. If this frost pattern does not clear within 24 hours, your unit will require manual defrosting.
STORAGE

121 CANS LOADING PLAN

Care and Maintenance

CLEANING YOUR APPLIANCE

• Turn off the power, unplug the appliance, and remove all contents from the appliance and store them in a suitable place.
• Clean the inside, the door seal and the inside of the glass with a clean, damp cloth.
• Never use detergents or other substances that emit odors.
• Always keep the door closed when cleaning the outside of the appliance. Make sure no detergent odors penetrate into the appliance.
• Clean the side panels and door surfaces with a clean and soft cloth. If necessary, use a moist cloth. Alternatively, use a microfiber cloth.
• The humidity tray should be hand-washed with water and detergent. After cleaning, always make sure the tray is thoroughly rinsed with clean water before replacing.

PREMISES POWER FAILURE

• In the event of a power interruption, temperature settings automatically defaults to factory settings once power is restored.

• Factory default temperature setting is 40ºF. To set a different desired temperature, refer to the “SETTING
  THE TEMPERATURE” and “ºC and ºF SELECTOR” section on page 8.

• Most power failures are corrected within a few hours and should not affect the temperature of your appliance
  if you minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need to take the proper steps to protect your contents.

VACATION TIME

• Short vacations: Leave the appliance operating during vacations of less than two days.
• Long vacations: If the appliance will not be used for an extended period, remove all items and turn off the appliance. Clean and dry the interior thoroughly.

MOVING YOUR APPLIANCE

• Remove all items inside the appliance.
• Securely tape down (we recommend using painter’s tape) all loose items (shelves) inside your appliance.
• Turn the adjustable legs up to the base to avoid damage.
• Tape (we recommend using painter’s tape) the door shut.
• Be sure the appliance stays secure in the upright position during transportation and protect the exterior of appliance with a blanket, or similar item.

PREPARING FOR STORAGE
If the beverage refrigerator will not be used for a long time, or is to be moved to another place, it will be necessary to defrost the unit and dry the interior.

1. Disconnect the beverage refrigerator from the power supply by removing the power plug from the wall
   socket.

2. Leave the door open to allow for air circulation and to prevent mold, mildew and unpleasant smells.

CAUTION: Store the unit out of the reach of children. If you have children, you may want to take additional precautions such as removing the door to prevent a child from being trapped inside the beverage refrigerator

NOTE:

• If the beverage refrigerator is unplugged, encounter power lost, or turned off; you must wait 3 to 5 minutes before restarting the beverage refrigerator.
• When the beverage refrigerator is used for the first time or restarted after having been shut off for a long time,
  there could be a few degrees variance between the temperature you select and the one indicated on the display. This is normal and it is due to the length of the inactivation time.

ENERGY SAVING TIPS

• The appliance should be located in the coolest area of the room, away from heat producing appliances, and out of any direct sunlight.
• Ensure that the appliance is adequately ventilated. Never obstruct the air vents.
• Close the door tightly and do not open the appliance too frequently or for a long period of time.
• Store the content in an organized way.
• Do not over load the appliance to allow air to circulate.

TRANSPORT OF THE BEVERAGE REFRIGERATOR
The ideal packaging for the beverage refrigerator is its original packaging. Please keep the original packaging handy and repack the beverage refrigerator if you need to transport the unit.

DEFROSTING
Under most ambient conditions, the beverage refrigerator does not need to be defrosted. In cold ambient temperatures and/or high humidity, some frost may build up. To defrost, remove all items, unplug the beverage refrigerator and leave the door open. Never use a knife or other metal instrument to scrape ice/frost. After defrosting, plug in the beverage refrigerator and set the desired temperature.

Troubleshooting

• There is a power failure.
• The appliance is not plugged in.·
• A house fuse has blown or the circuit breaker is tripped.

|

• Ensure the appliance is plugged in and the power outlet has power.
• Replace the broken fuse or reset the break-er.

The appliance is not reaching the desired temperature|

• The appliance is placed too close to a heat source
• The door is opened too often.
• The door is not closed completely.
• The door gasket does not seal proper- ly.

|

• Adjust the temperature.
• Keep the appliance away from sunshine or other heat sources.
• Close the door tightly and do not open the door too frequently or for a long period of time.
• Ensure the door gasket is not loose..

Frost forming inside the appliance|

•  The environment is too humid.
• The ambient temperature is too low.
• The door is opened too frequently for a long period of time.
• Items are blocking the internal fan.

|

• Although this unit uses an auto-defrost sys- tem, under certain conditions, manual de- frosting may required. If frost builds up, try running the unit on a warmer temperature setting.
• Close the door tightly and do not open the door too frequently or for a long period of time.
• Unplug the unit to allow the frost to melt.
• Move items so they do not block the fan.

Condensation builds up on the glass door.|

• Ambient temperature or humidity is high.

|

• Lower the room humidity by a dehumidifier or air conditioner.

The appliance turns itself on and off frequently|

• The ambient (room) temperature is too low or high.
• A large amount of contents has been added to the appliance.
• The door is opened too often.
• The door is not closed completely.
• The door gasket does not seal proper- ly.

|

• Decrease or increase the ambient (room) temperature.
• To minimize internal temperature fluctuation, do not add large amount of contents at once.
• Close the door tightly and do not open the door too frequently or for a long period of time.
• Ensure the door gasket is not loose.

The appliance makes too much noise|

• If the noise is from the fan, it may be normal operating noise.
• Contraction and expansion of the in-side walls may cause popping and crackling noises.
• The appliance is not level.

|

• The fan makes normal fan noises.
• Some popping or cracking noises are nor- mal. They are caused by expansion and contraction of the inside walls due to tem- perature changes.
• Make sure the unit is on a hard and level surface. Do not place the appliance on car- pet.
• See Normal Sounds

The door does not close properly|

• The appliance is not level.
• The door was reversed and not properly installed.
• The shelves are out of position .

|

• Make sure the appliance is on a hard and level surface. Avoid placing the appliance on a carpeted or soft surface.
• Reinstall door.
• Correctly install the shelves.

ONE YEAR LIMITED WARRANTY

This WHYNTER product is warranted, to the original owner within the 48 continental states, for one year from the date of purchase against defects in material and workmanship under normal use and service. When making a warranty claim, please have the original bill or invoice of purchase with purchase date available.
Should your WHYNTER product prove defective within one year from the date of purchase, return the defective part or unit, freight prepaid (within two months of purchase; after two months to one year, customer will be responsible for freight cost to Why nter’s service department), along with an explanation of the claim to Whynter LLC. A return authorization number issued by Whynter is required for all warranty claims and returns. Please package the WHYNTER product carefully in its original packaging material to avoid damage in transit. The original box and packaging material should be retained, as Whynter is not responsible for the cost of replacement packaging. Under this warranty, Whynter will repair or replace any parts found defective at our discretion. This warranty is not transferable. After the expiration of the warranty, the cost of labor and parts will be the responsibility of the original owner of the unit.

THIS WARRANTY DOES NOT COVER:

• Acts of God, such as fire, flood, hurricanes, earthquakes and tornadoes.
• Improper power supply such as power surge, low voltage, defective household wiring or inadequate fuses.
• Use in commercial or industrial applications.
• Damage, accidental or otherwise, to the product while in the possession of a consumer not caused by a defect in material or workmanship.
• Damage caused by consumer misuse, tampering, lack of maintenance or failure to follow the care and special handling provisions in the instructions.
• Damage to the finish of the case, or other appearance parts caused by wear.
• Damage caused by repairs or alterations to the product by anyone other than authorized by the manufacturer.
• Removal, Replacement Packaging, Freight and Insurance cost for the warranty service.
• Products sold AS IS or from an unauthorized reseller.
• Products that have had their serial numbers removed or defaced.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. WHYNTER SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE- QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

Please retain the original proof of purchase in order to obtain warranty services.
Warranty begins from the original date of purchase.
To obtain service or information, contact
Whynter LLC via email at support@whynter.com or call
866-WHYNTER.
Product contents and specifications may change without notice.
Copyright © 2023 Whynter LLC
WWW.WHYNTER.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>