PHILIPS BVP282 Tango G2 Gen 4.0 Solar Instruction Manual
- June 9, 2024
- Philips
Table of Contents
PHILIPS BVP282 Tango G2 Gen 4.0 Solar
Product Information
The BVP282 is a flood lighting luminaire designed for outdoor use only. It uses LEDs as the light source and operates at 240V with a frequency of 50-60 Hz. The luminaire has an IP66 classification and weighs 2.4 kg. The dimensions of the luminaire are represented in the table below:
| Type | A | B | C | D | E |
|---|---|---|---|---|---|
| 100W | 264mm | 203mm | 52mm | 160mm | 300mm |
The luminaire is equipped with a mounting screw size of M8 and comes with a spring washer and flat washer. The luminaire requires a proper junction box of IP66 protection for the termination of the wire to ensure electrical safety and product performance. Note that the junction box is not part of the supply.
Product Usage Instructions
Installation
- The luminaire should be installed by a qualified electrician.
- Turn off power before inspection, maintenance, installation, or removal.
- Refer to the technical datasheet for additional electrical properties to ensure safe installation.
- The luminaire must not be in contact with combustible materials.
- Ensure power supply cables (L-N-E) are connected correctly before switching on.
- The connection of power cable on the luminaire is type Y. If the external flexible cable or cord of the luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid hazard.
- The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire shall be replaced.
- Warranty void if earthing is not connected.
Mounting
- Ensure that the gland is never above the center line.
- Adjust the aiming of the luminaire and tighten the mounting
screws on the side for locking in position using a torque of 8 N-m.
Maintenance
- Periodic cleaning of the luminaire glass cover will ensure max. optical efficiency.
- Use water and non-abrasive soap, cleaner or detergent solution to clean the luminaire glass cover.
Caution
- The luminaire must be used within the applicable product specifications, installation instructions, and environmental conditions for storage & operations according to applications guidelines provided by Philips for the product Warranty to be valid.
- In case the front glass is found broken/ damaged, it should not be powered on and is to be replaced before using the luminaire.
Dimension
All dimensions are in mm.
| Type | A | B | C | D | E |
|---|---|---|---|---|---|
| 100W | 264 | 203 | 52 | 160 | 300 |
INSTALLATION INSTRUCTION
- Red/Brown – Live
- Grn-Yel – Earth
- Black/Blue – Neutral
- Use the proper junction box of IP66 protected for termination of the wire to ensure electrical safety and product performance.
- (Junction Box is not part of the supply)
- Adjust the aiming of the luminaire and tighten the mounting screws on the side for locking in position using a torque of 8 N-m
- Caution: Gland shall never be above the center line.
BVP 282 Flood Lighting Luminaire
- Type : BVP282
- Light Source : LED’s
- Voltage : 240V, 50-60 Hz
- IP Classification: IP-66
- Net Weight: 2.4 kg
- Application : Outdoor use only
Warning
- The luminaire shall be installed by a qualified electrician.
- Turn power off before inspection, maintenance, installation or removal.
- Refer to technical datasheet for additional electrical properties to ensure safe installation.
- Luminaire installed must not be in contact with combustible materials.
- Ensure power supply cables (L-N-E) are connected correctly before Switching on.
- The connection of power cable on luminaire is type Y. If the external flexible cable or cord of the luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid hazard.
- The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire shall be replaced.
- Warranty void if earthing is not connected
Maintenance
- Periodic cleaning of the luminaire glass cover will ensure max. optical Efficiency.
- The luminaire glass cover shall be cleaned with water and non-abrasive soap, cleaner or detergent solution.
Caution
- The luminaire must be used within the applicable product specifications, installation instructions and environmental conditions for storage & operations according to applications guidelines provided by Philips for product Warranty to be valid.
- In case the front glass is found broken/ damaged, it should not be powered on and is to be replaced before using the luminaire.
Dimension
All dimensions are in mm.
| Type | A | B | C | D | E |
|---|---|---|---|---|---|
| 100W | 264 | 203 | 52 | 160 | 300 |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>