vlectro S6520 Soundbar Instruction Manual

vlectro S6520 Soundbar

Specifications

• Connectivity: ARC, OPTICAL, USB, AUX IN, AUX OUT, DC
• Supported Modes: MOVIE, MUSIC, DIALOGUE
• Controls: MUTE, VOL+, VOL-, TREB+, TREB-, BASS+, BASS+

Product Usage Instructions

Wall Mounting Instructions

1. Place the wall mount guide against the wall surface.
2. Mark the four bracket holes for supporting screws using a pencil and then remove the wall mount guide.
3. Ensure the template is level and leave at least 3 inches of space between the template and the TV.
4. Use an appropriate size drill bit to drill a hole in each wall where marked.
5. Push the screw onto the bracket and firmly screw each screwinto the mounting hole.

Wall mount equipment installation

1. Install the Sound Bar by hanging the bracket on the wall securely.

Box Contents

LED Indicators and Button Introduction

Right side of Sound Bar

Know Your Remote

Connection Diagram

• a. Bluetooth
• b. High speed ARC cable (not supplied)
• c. Digital Optical cable (supplied)
• d.e. 3.5mm to 3.5mm audio cable
• f. USB (not supplied)
• g.Power Adapter (supplied)

Connecting with a TV

Setting “PCM” on your TV
When all cables are connected properly, and LED indicator lights properly, if there is no sound from the tv or Sound Bar, please set your tv as below:

1. Press “Menu” on the TV’s remote control.
2. Press the arrow keys on the remote to scroll to “Audio Settings.”
3. Press “OK” on the remote control.
4. Scroll to “Advanced Audio” and press “OK”. Some televisions may not have an”Advanced Audio” menu and may list various audio settings instead.
5. Scroll to “Audio Output Mode” or “Digital Audio Output Mode” and press “OK”.
6. Scroll until “PCM” is displayed as the current audio output.
7. Press “OK” to save the settings.

Connecting a Bluetooth Device

• a. Press the “BT” button on the remote or press the “ ” button on the right side of the Sound Bar, the LED indicator blinks blue.
• b. Turn on Bluetooth on the Bluetooth device.
• c. Select “Vlectro Soundbar 5.0” and connect it. When your Bluetooth device is connected, the LED indicator blinks blue slowly.
• d. Play music files from the device, connected via Bluetooth, through the Sound Bar.
• e. Press and hold the “BT” key to disconnect the currently connected Bluetooth and re-enter pairing

Installing the Wall Mount

1. Place the wall mount guide against the wall surface. Push a pencil tip to mark the four bracket holes for supporting screws, and then remove the wall mount guide.
   • The template must be level.
   • Leave 3 inches at least between the template and the TV.
2. Use an appropriate-sized drill bit to drill a hole in each wall. Push the screw onto the bracket, and then firmly screw each screwinto the mounting screw hole.
3. Install the Sound Bar by hanging the bracket on the wall.

Troubleshooting

• • The cables between Sound Bar and input devices are securely connected, and the power adapter is also connected to a working power source.
• • The adapter LED indicator is lighting, and the LED indicator is lit in the middle of the Soundbar.

No sound or crackling noise

• Check if all cables are connected properly.
• Press Mute on the remote to ensure the Sound Bar is not muted.
• Press Volumet on the remote or the right side of your Sound Bar.
• Make sure you have selected the right input source on your remote, and that the LED is lighting accordingly.
• If using Bluetooth, check if the sound on your device is under minimum volume.
• If using Optical/ARC, check if your device (TV/Cable Box/Projector/etc.) audio output is set to PCM or turn the Dolby/DTS off.
• When using a cable connection, make sure your device has an audio output port (not an input).

Remote isn’t working

• Check if the battery is installed properly with power.
• Check if the signal of the receiver is covered by something.

I hear buzzing or humming

• Ensure all cables and wires are securely connected.
• Connect a different source device (TV, Blu-ray player, etc) to see if the buzzing persists. If it does not, the problem may be with the original device.
• Connect your device to a different input on the Sound Bar.

Bluetooth can’t be connected

• Check if the Sound Bar is connected to the third Bluetooth device.
• Be sure that there are no solid obstructions between the Sound Bar and the source device. (within 30 feet)
• Reboot the Bluetooth and connect again.

Hear echo when watching TV

• Setting your TV audio to External Speaker. Mute the TV speaker.

FAQ

Frequently Asked Questions

• Q: How much space should be left between the template and the TV during wall mounting?
  • A: At least 3 inches of space should be left between the template and the TV to ensure proper installation.
• Q: What are the supported connectivity options for this product?
  • A: The product supports connectivity via ARC, OPTICAL, USB, AUX IN, AUX OUT, and DC inputs.

DECLARATION OF CONFORMITY

Confinity NV, Dorp 16, 9830, Sint-Martens-Latem, Belgium declares the following device in sole responsibility:

• Brand name: Vlectro
• Product type: Soundbar 5.0
• Item number: OP_012877

Complies with the following harmonization rules:

• EN 62479: 2010
• EN 62368-1: 2014+A11:2017
• ETSI EN 301 489-1 V22.3 (2019-11)
• Draft ETSI EN 301 489-17 V3.2.2

Signed for and on behalf of:
Sint-Martens-Latem, Belgium – DEC 2023
A. Pappijn – Product Manager

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>