GE GTX38EASWWS Capacity Electric Dryer User Guide

GE GTX38EASWWS Capacity Electric Dryer

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

ELECTRIC DRYER RATING:

240V| 5600W| 24A| 60Hz
208V| 4400W| 22A| 60Hz

EXHAUST OPTION: 4-way rear, right, left and bottom

CIRCUIT REQUIREMENTS: An individual, properly-grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.

NOTE: Dryer wall outlet must be located within 36″ of service cord entry and acessible when dryer is mounted in position.

INSTALLATION INFORMATION:

For complete information, see installation instructions packed with your dryer.

SPECIAL INSTALLATION REQUIREMENTS

ALCOVE OR CLOSET INSTALLATION:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0″ either side; 1″ front, top and rear
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

BATHROOM OR BEDROOM INSTALLATION:

• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:

• Minimum clearances to combustible surfaces are: 0″ both sides; 1″ rear

DRYER EXHAUSTING INFORMATION:

• Use metal duct only, vertical and horizontal ducting.

FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED WITH YOUR DRYER.

DUCTING MATERIALS:

For best performance, this dryer should be vented with a 4″ diameter all-rigid metal exhaust duct. If a rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil- type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4″ diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil-type) ducting.

EXHAUST LENGTH CALCULATION:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4″ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

CAUTION: For personal safety, do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12″ above the ground or any other obstruction with the opening pointed down.

FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.

DRYER EXHAUSTING INFORMATION USE METAL DUCT ONLY VERTICAL AND HORIZONTAL DUCTING

Domestic dryer models

BEST PERFORMANCE

Maximum length of 4″ dia rigid metal duct
Exhaust hood type
Number of 90° turns| A 4″ opening| B 2-1/2″ opening
Long Vent 6.1-7.4 cu. ft. capacity electric & gas (GTD33, GTD42, GTD45, GTD65, GTX22, GTX33, GTX38 GTX42 and GTX65)| 0
1
2
3
4
5| 120 ft.
100 ft.
85 ft.
70 ft.
60 ft.
55 ft.| 90 ft.
75 ft.
65 ft.
55 ft.
45 ft.
35 ft.

For every extra 90° elbow, reduce the allowable vent system length by 10 ft.

Two 45° elbows will be treated like one 90° elbow.

For the side exhaust installations, add one 90° elbow to the chart.

When calculating the total vent system length, you must add all the straight portions and elbows of the system (including the transition duct).

POWER CORDS:
GE Appliances strongly recommends the use of factory specified parts. Select the power cord to fit your installation requirements.*

NOTE: If the dryer circuit is on a circuit protected by a GFCI breaker, then 3-wire installation is not permitted. Hose wiring and dryer must be configured for 4-wire.

FEATURES AND BENEFITS

Shallow Depth – Reaching into your dryer is easier than ever thanks to the shallow-depth design, which also fits into more spaces without sacrificing capacity.

Auto Dry – Auto Dry monitors the internal air temperature to determine the ideal drying time, protecting your garments from overdying.

Powerful Venting & Flexible Installation – Powerful airflow offers long- lasting performance from lint build-up and offers venting solutions up to 120 feet for greater installation flexibility .

Large Diffuser for Even Drying – A large internal heat diffuser allows for warm air to evenly spread throughout your clothes during the cycle, making this the ideal dryer for large loads and bulky items.

Delicates Cycle – This delicate, low heat dryer setting helps protect fabrics and extends the lifetime of even your most delicate items.

Durable Aluminized Drum – This durable, long-lasting design resists corrosion and optimizes drying performance.

Reversible Dryer Door – Door can swing from either direction making it easier to access the last sock from the back of the drum.

Temperature Selection – Offer a range of drying temperatures to adjust to the specific needs of your garments for personalized garment care.

Up Front Lint Filter – Simplify the task of lint removal with our convenient upfront lint filter, enhancing airflow within the appliance and for your garments.

MATCHING DRYER:

GTW385ASWWS – GE® 4.3 cu. ft. Capacity Washer with Stainless Steel Basket, Cold Plus and Water Level Control

ACCESSORIES*

UL approved – installer pkg
PM08X10085| 8′ Flexible Dryer Duct with 2 screw clamps – UL approved – retail pkg
WX8X73| 8′ Flexible Dryer Duct w/ 2 tension clamps – UL Approved
PM8X73| 8′ Flexible Dryer Duct w/ 2 tension clamps – UL Approved – retail pkg
WX08X10130-100PK| 4″ Dryer Tension Clamp – only available in boxes of 100 now
WX08X10131-50PK| 4″ Dryer Screw Clamp – only available in boxes of 100 now (50 2 packs)
WX8X74| 50′ Dryer Duct
PM08X10078| Dryer Vent Close Elbow – turns 90° within 4″
WX14X10010| Dryer Steam Kit with Brass Y (Rubber)
PM08X10078| Universal Dryer Vent Close Elbow
PM8X85| Universal Outdoor Dryer Exhaust
WX09X10002| 4′ 30 Amp. 3-Wire Dryer Cord
WX09X10003| 5′ 30 Amp, 3-Wire Dryer Cord
WX09X10004| 6′ 30 Amp 3-Wire Dryer Cord
WX09X10018| 4′ 30 Amp. 4-Wire Dryer Cord
WX09X10019| 5′ 30 Amp. 4-Wire Dryer Cord
WX09X10020| 6′ 30 Amp. 4-Wire Dryer Cord
WX14X10012| Dryer Steam Kit with Brass Y (Stainless Steel-Installer)
WE01X25160| Dryer Rack
WE49X22606| Rear Exhaust Opening Cover

*Accessories sold separately..

CUSTOMERS SUPPORT

Listed by Underwriters Laboratories

Specification Revised 02/24

*Order online at GEApplianceparts.com, 24 hours a day or by phone
at 877.959.8688 during normal business hours.

References

• Appliance Parts, Accessories & Water Filters | GE Appliances
• GE Appliances: Shop for Home, Kitchen, & Laundry Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>