KARCHER SC 1402 Cylinder Steam Cleaner Instruction Manual

SC 1402 Cylinder Steam Cleaner
Instruction Manual

Quick Reference

|
---|---

Dear Customer,
Please read and comply with these instructions prior to the initial operation of your appliance. Retain these operating instructions for future reference or for subsequent possessors.
Proper use
Only use the steam cleaner for private household applications. The unit is meant for steam cleaning and can be used with appropriate accessories as described in these operating instructions. Especially mind the safety instructions during use.

**Quick Reference

**

( See page 2).

1. Fill the water reservoir up to the “MAX” marking.

2. Insert the steam plug into the appliance connector.

3. Connect the accessories to the steam gun. Plug in the mains plug.

4. Turn on the appliance.
   The green and orange indicator lamps light up. The water pump fills the steam boiler from the water reservoir.
   Before the initial operation and after descaling, the water reservoir will need to be filled twice.

5. Wait (for approximately 8 minutes) until the orange indicator lamp goes out.

6. The steam cleaner is ready to use.

Description of the Appliance

⇒ See page 3.

A1 Appliance connector with cover
A2 Water reservoir
A3 Switch – ON/OFF
A4 Accessory compartment
A5 Power cord
A6 Steam boiler seal
A7 Handle
A8 Funnel inlet
B1 Indicator lamp (red) – lack of water steam boiler
B2 Indicator lamp (green) – operative
B3 Indicator lamp (orange) – heating
C1 Steam gun
C2 Unlocking button
C3 Lock (child-proof lock)
C4 Steam switch
C5 Rotary knob – adjusting the steam quantity
C6 Steam hose
C7 Steam plug| D1 Detail nozzle
D2 Extension piece
D3 Round brush
D4 Power nozzle (red)
E1 Manual nozzle
E2 Terry cloth coverF1 Window nozzle
G1 2 extension pieces
G2 Unlocking button
G3 Parking device
H1 Floor nozzle
H2 Retaining clip
H3 Floor cleaning cloth
K1* Steam iron
K2 Indicator lamp – steam iron heating
K3 Switch – steam ironing
K4 Temperature controller
K5 Steam plug
---|---

• available as an optional accessory
  Symbols on the machine
  Steam
  CAUTION – Danger of scalding

Safety Instructions

Warnings and notes that are attached to the appliance provide important notes for safe operation.
Apart from the notes contained herein the general safety provisions and rules for the prevention of accidents of the legislator must be observed.
Electrical connection

• Only connect the appliance to properly earthed sockets.

• The voltage indicated on the type plate must correspond to the voltage of the socket.

• In wet rooms, e.g. bathrooms, connect the appliance to sockets with a series of connected RCD adapters. If you are not sure, please contact an electrician.

• Never touch the mains plug and the socket with wet hands.

• Make sure that the power cord or extension cables are not damaged by running over, pinching, dragging, or similar.
  Protect the power cord from heat, oil, and sharp edges.

• Only use a splashproof extension cable with a minimum section of 3×1 mm².

• The connection between the power cord and extension cable must not lie in water.

• Never use a damaged power cord or extension cable! If the power cord is damaged it must be replaced with a special power cord available from the manufacturer or his customer service.

• If couplings of the power cord or extension cable are replaced the splash protection and mechanical tightness must be ensured.

Application

• Check the faultless condition of the appliance and the accessories before using it. Otherwise, the appliance must not be used. Please check in particular the power cord, the steam boiler seal, and the steam hose.
• The steam hose must not be damaged (risk of scalds). A damaged steam hose must be replaced immediately. You may only use a steam hose that is recommended by the manufacturer (see spare parts list for the order number).
• Never fill solvents, solvent-containing liquids, or undiluted acids (e.g. detergents, benzene, paint thinner, and acetone) into the water reservoir as these substances affect the materials used on the appliance.
• It is not allowed to use the appliance in hazardous locations. If the appliance is used in hazardous areas the corresponding safety provisions must be observed.
• The appliance must be used on a flat surface.
• The steam switch must not be locked during the operation.
• Never touch the steam jet with your hands and never direct the steam jet to persons or animals (risk of scalds).
• Never use the appliance to clean objects containing hazardous substances (e.g. asbestos).
• The operator must use the appliance properly. He must consider the local conditions and must pay attention to third parties, in particular children, when working with the appliance.
• This device is not intended for use by persons (including children) with reduced physical, sensory or mental abilities or lacking experience and/or knowledge unless they are supervised by a person responsible for their safety or are instructed by these persons on the use of the device. Children should be supervised, to ensure that they do not play with the device.
• Never leave the appliance unattended as long as it is in operation.

Steam cleaning electric household appliances

• If you use the appliance to clean electric household appliances (e.g. electric kitchen ranges) these appliances must be off circuit (switch off the fuse). Before you use the appliances again make sure they have dried completely. Please observe the notes of the appliance manufacturers!
• Do not use the steamer on electrical appliances such as lamps, hair driers, or electric heaters, as the steam may cause an electrical defect.

Maintenance

• Turn off the appliance and remove the mains plug prior to any care and maintenance works.
• The steam boiler seal may only be opened to descale the appliance.
• Never open the steam boiler seal if the appliance is hot or turned on.
• Repair works may only be performed by the authorized customer service.

Storage

• Caution: Never operate or store the appliance in a horizontal position!
• Protect the unit from rain. Do not store outside.

Safety elements
This steam cleaner is equipped with several safety devices that provide all- around protection for the appliance. The most important safety devices are described in the following.
Pressure controller
The pressure controller keeps the boiler pressure during the operation as constant as possible. The heating is turned off if the maximum operating pressure of 3.5 bar is reached in the boiler and is reactivated in case of a pressure drop in the boiler due to steam tapping.
Boiler thermostat
If there is no water in the boiler the temperature in the boiler rises. The boiler thermostat turns off the heating. The heating is prevented from being turned on again until the boiler has been filled.
Safety thermostat
If the boiler thermostat fails and the appliance overheats, then the safety thermostat turns off the appliance.
Please contact your local Kärcher customer service to arrange for the rest of the safety thermostat.
Steam boiler seal
The steam boiler seal acts as a pressure control valve at the same time. It seals the boiler against the steam pressure that builds up in the boiler.
If the pressure controller is defective and the steam pressure in the boiler rises above 5.7 bar, the steam boiler seal opens, and steam is emitted through the lock to the outside. Please contact your local Kärcher customer service before you put the appliance into operation again.

Preparing the Appliance

Unpacking the Appliance
When you unpack the system, check that everything is complete (see page 3). If there are any missing parts or you detect any transport damage when unpacking, please inform your dealer immediately.
The packaging materials are recyclable. Please do not throw the packaging in the domestic waste but pass it on for recycling.
Old units contain valuable recyclable materials. Batteries, oil, and similar substances may not be released into the environment. Therefore please dispose of old units through suitable collection systems.
Storing the Accessories
⇒ Place the manual nozzle (E1) into the appropriate accessory compartment (see Fig. 1).
Note: The detail nozzle (D1), the extension piece (D2), the round brush (D3), and the power nozzle (D4) are already stored.

⇒ Hold the unlocking button down, and push the parking device (G3) on an extension tube (G1) until it locks into place in the second aperture. The parking device must lock into place when you release the unlocking button (see Fig. 2). ⇒ Put the floor nozzle (H1) on the extension piece with the parking device.
⇒ Insert the window nozzle (F1) on the second extension piece.
⇒ Put the extension pieces into the large accessory compartments (see Fig. 3).

Putting Down the Accessories
If you interrupt your work for a short period of time, the extension tube with the floor nozzle can be put into the parking position (see Figure 4).

Operation

Attaching the Accessories
⇒ Tightly insert the steam plug (C7) into the appliance connector (A1). The locks of the steam plug must lock into the cover of the appliance connector (see Figure 5).

⇒ Connect the required accessories (D1, E1, F1) with the steam gun (C1). Insert the open end of the accessory on the steam gun (C1) and push it onto the steam gun until the unlocking button (C2) of the steam gun locks into place (see Fig. 6).

⇒ Use the extension pieces (G1) if necessary. To do so, connect one or both extension pieces to the steam gun (C1) (see Fig. 7). Insert the required accessories (D1, E1, F1, H1) on the free end of the extension piece.

⇒ The detail nozzle (D1) may also be used with the extension piece (D2), the round brush (D3), or the power nozzle (D4) (see Fig. 8). To do so, put the two grooves of the attachments on the locks of the detail nozzle and turn clockwise until the stop.

Removing the Accessories
DANGER
Hot water may drip out of the accessory parts while you are detaching them! Never detach accessory parts while steam streams out – the risk of scalds!
⇒ To detach the accessory parts, press the unlocking button (C2 or G2), and pull the items apart (see Figure 9).

⇒ To detach an attachment from the detail nozzle, turn the attachment counterclockwise and pull the parts apart.
Filling the Water Reservoir
You can remove the water reservoir to fill it or you can fill it directly on the appliance.
Note: If you always use the usual commercial distilled water it is not necessary to descale the boiler.
CAUTION
Do not use condensation water from the drier! Do not fill in detergents or other additions!
A) Remove the water reservoir
⇒ Pull out the water reservoir using the handle (A8).
⇒ Fill the water reservoir up to the “MAX” marking.
⇒ Insert the water reservoir and press downwards.
B) Directly on the appliance
⇒ Pour water from a container into the funnel inlet (A9). Fill up to the “MAX” marking.
Turning on the Appliance
Note: Before the initial operation and after descaling, the steam boiler must be filled with water. For this purpose, the water reservoir will need to be filled twice.
⇒ Insert the mains plug into a socket.
⇒ Press the switch (A3) to turn on the appliance. The green (B2) and orange (B3) indicator lamps will light up.
Note: If there is no or not enough water in the boiler, the pump starts and supplies water from the reservoir into the boiler. The filling process may take several minutes.
⇒ The orange indicator lamp (B3) goes out after approximately 8 minutes. The appliance is ready for use.
⇒ Push the lock (C3) of the steam switch forward.
Note: If you push the lock (C3) backward, the steam switch (C4) cannot be activated (child-proof lock).
⇒ Activate the steam switch (C4).
⇒ Always direct the steam gun (C1) at a separate piece of cloth until the steam is emitted evenly.
Note: The heater of the steam cleaner is turned on at regular intervals during the operation of the appliance in order to maintain the pressure in the boiler at a constant level. When the heater is turned on, the orange indicator lamp (B3) lights up.
Adjusting the Steam Quantity
The steam quantity is adjusted using the rotary knob (C5) on the steam gun (C1).
⇒ If you turn the rotary knob forward: a higher steam quantity is emitted,
⇒ If you turn the rotary knob backward: a lower steam quantity is emitted.
Refilling Water
The water reservoir may be refilled at any time.
Note: If there is not enough water in the steam boiler the pump automatically supplies water from the water reservoir into the steam boiler. If the water reservoir is empty, the pump is not able to fill the steam boiler and the steam tapping is blocked.
Indicator lamp (B1) – low-water blinks.
⇒ Fill the water reservoir.
Note: The pump tries to fill the steam boiler in short intervals. If the filling is successful, the steam tapping is released immediately, and the red indicator lamp goes out.
Turning Off the Appliance
⇒ Press the switch (A3) to turn off the appliance.
⇒ Disconnect the mains plug from the socket.
⇒ Press the cover of the appliance connector (A1) to the bottom and disconnect the steam plug (C7) from the appliance connector.
⇒ Empty the residual water from the water reservoir.
Storing the Appliance
⇒ See page 20, “Storing the Accessories”.
⇒ Always make sure that the brushes are cold before storing them to avoid deformation of the bristles.

How to Use the Accessories

Important Application Instructions
Cleaning of Textiles
Before you use the steam cleaner for the cleaning of textiles, you should always test the resistance of the fabrics against steam by means of cleaning a hidden spot. Apply steam to the hidden spot, and then let it dry. Check whether the color and shape of the area have changed.
Cleaning of Coated or Lacquered Surfaces
WARNING
Never direct the steam jet at glued edges as the edge band may loosen. Do not use the steam cleaner on wooden or parquetry floors that have not been sealed.
Be careful when you clean kitchen and living room furniture, doors, parquetry, and lacquered or plastic-coated surfaces! Upon a longer influence of steam, wax, furniture polish, plastic coatings, or paint may come off, or stains may occur. Therefore, you should only clean such surfaces using a piece of cloth to which steam has been applied or very briefly using a double layer of cloth on the nozzle.
Cleaning of Glass
WARNING
Never direct the steam jet directly at the sealed parts of the window around the window frame to prevent damage to the sealing.
In case of low outside temperatures, especially in the winter, warm up the window pane. Apply a small quantity of steam to the entire glass surface. Thus, you compensate for temperature differences and avoid stresses on the glass surface. This is of importance because glass surfaces that are heated unevenly may crack.
Steam gun (C1)
You can use the steam gun without any additional accessories.
Application:

• elimination of odors and creases from garments: Apply steam to the hanging garment from a distance of 10–20cm.
• removing dust from plants: Respect a distance of 20-40 cm.
• dusting with a damp cloth: Apply a small amount of steam to a cloth, and then use this cloth to wipe over the furniture.

Detail nozzle (D1)
The closer you hold the nozzle to the dirty spot, the higher the cleaning effect as the temperature and pressure of the steam reach their maximum values immediately when they are emitted from the nozzle.
Application:

• fittings drain
• wash-basins, toilets
• blinds, radiators
• Removing stains: Moisten stubborn limescale with vinegar, and allow to react for approximately 5 minutes.

Extension piece (D2)
The extension piece is attached to the detail nozzle.
Application:

• inaccessible gaps, joints, etc.

Round brush (D3)
Note: The round brush is not suited for the cleaning of delicate surfaces.
The round brush is attached directly or using the extension piece (D2) on the detail nozzle.
Application:

• locations that are difficult to access, such as corners and joints
• fittings drain

Power nozzle (D4)
The power nozzle is attached directly or using the extension piece (D2) on the detail nozzle. The power nozzle increases the emission speed of the steam.
Application:

• removal of especially stubborn dirt
• cleaning out corners, joints, etc.

Manual nozzle (E1)
Pull the terry cloth cover (E2) over the manual nozzle.
Application:

• small, washable surfaces, such as kitchen surfaces made of plastic, tiled walls
• windows, mirrors
• furniture fabrics
• vehicle interior, windscreens
• bath-tubs

Window nozzle (F1)
Application:

• windows
• mirrors
• glass surfaces on shower cubicles
• other glass surfaces

⇒ Apply steam to the glass surface from a distance of approximately 20 cm until the surface is moistened evenly. Then push the lock (C3) to the rear to prevent an undesired actuation of the steam switch (C4). Wipe the glass surface in straight lines from the top to the bottom using the rubber lip of the window nozzle. Wipe the rubber lip and the bottom edge of the window dry after each strip.
⇒ Before cleaning with the window nozzle, dissolve fat residue using the manual nozzle (E1) and a terry cloth cover (E2).
Floor nozzle (H1)
Application:

• all washable wall and floor coverings, e.g.: stone floors, tiles, and PVC floors.

⇒ Attach the floor cloth to the floor nozzle.

1. Fold the floor cloth the long way and place the floor nozzle on top of it.
2. Open holding clamps.
3. Place the cloth ends into the openings.
4. Close the holding clamps.

Caution
Do not insert fingers between the clamps.

⇒ To remove the cloth, press the retaining clips (H2), and pull out the cloth.
⇒ Turn and exchange the floorcloth at regular intervals. Thus, you improve the ability to pick up dirt.
⇒ Work slowly on very dirty surfaces to allow the steam to act on the dirt for a longer period of time.
⇒ If there are residues of detergents or floor cleaning products (e.g. wax, liquid polish) on the surface to be cleaned, streaks may form during the cleaning. These streaks normally disappear after repeated use of the steam cleaner.
Steam iron (K1) (optional)
For special accessories, see page 26 for the order number.
⇒ Firmly insert the steam plug (K5) into the appliance connector (A1). The locks of the steam plug must lock into the cover of the appliance connector.
Steam ironing
We recommend the use of the Kärcher ironing table with active steam extraction. This ironing table has been specially designed to match your new unit. It facilitates and, thus, accelerates the ironing process substantially. In any case, you should use an ironing table that is covered with a mesh-type underlay allowing the steam to pass through.
⇒ All fabrics can be steam ironed. Adjust the temperature regulator (K4) of the steam iron within the notched range (•••/MAX). Delicate imprints or fabrics should be ironed on the reverse or according to the manufacturer’s specifications. For this, you can use our antistick sole plate (see optional accessories overview).
⇒ Once the indicator light on the steam iron (K2) has gone out, the steam iron is ready for use. The sole plate must be hot to prevent the steam from condensing on the sole plate and dripping onto the garment to be ironed.
⇒ Press the switch (K3) on the iron. Steam flows out on the sole plate.
– Press the switch to the front: A steam burst is emitted while the switch is being pressed.
– Press the switch to the back: The switch locks and steam is continuously emitted. To release, press the switch to the front.
⇒ Direct the first burst of steam at a separate piece of cloth until the steam is emitted evenly.
⇒ You can hold the iron in an upright position to apply steam to curtains, dresses, etc.
Dry ironing
⇒ Adjust the temperature of the iron according to the garment you want to iron.
• Man-made fiber
•• Wool
••• Linen
Wallpaper remover (optional)
For special accessories, see page 26 for the order number.
You can use the wallpaper remover with the steam cleaner to remove paper wallpapers.
⇒ Place the entire surface of the wallpaper remover along the edge of a strip of wallpaper. Switch on the steam supply (C4) and allow the steam to act on the wallpaper until it is completely soaked (approximately 10 seconds).
⇒ Move the wallpaper remover to the next piece of wallpaper you want to remove. Hold the steam switch (C4) pressed while you move the tool. Lift the soaked piece of wallpaper using a flat trowel, and pull it off the wall. Move the wallpaper remover from strip to strip, and pull the wallpaper off in strips.
⇒ In the case of woodchip wallpaper that has been painted several times, the steam may not be able to soak the wallpaper. Thus, we recommend preparing the wallpaper using a spiked roller before steam is applied.
Steam turbo-brush (optional)
For special accessories, see page 26 for the order number.
The steam turbo-brush is rotated by the emitted steam and is ideally suited for the easy cleaning of extreme dirt at places in the kitchen and the bathroom that are difficult to access.
Application:

• cleaning of corners, joints
• areas that are difficult to access

Textile cleaning nozzle (optional)
For special accessories, see page 26 for the order number.
Application:
To freshen hanging textiles, such as jackets or curtains, by means of two functions:

• Defleecing garment using the thread lifter.
• Vaporizing and de-wrinkling of textiles (also eliminates odors).

If you activate the steam switch, steam is emitted. Direct the first burst of steam at a separate piece of cloth until the steam is emitted evenly.
Special Accessories Overview
Steam iron with special steel sole (order no. 2.884-503)
Anti-stick sole plate (order no. 2.860-132)
Professional steam iron with the aluminum sole (order no. 2.884-504)
Anti-stick sole plate (order no. 2.860-131)
Ironing table with active steam extraction (order no. 6.906-002)
For excellent ironing results with a substantial saving of time (only for 230 V)
Wallpaper remover (order no. 2.863-062)
Round brush kit (order no. 2.863-058)
– 4 round brushes for the detail nozzle.
Round brush kit with brass bristles (order no. 2.863-061)
– 3 round brushes for the detail nozzle (for particularly stubborn dirt)
Terry cloths (order no. 6.369-481)
– 5 floorcloths
Terry covers (order no. 6.370-990)
– 5 covers
Terry cloth kit (order no. 6.960-019)
– 2 floorcloths, 3 covers
Microfibre cloth kit (order no. 6.905-921)
– 1 floorcloth, 1 cover with extremely high absorbency, and the ability to pick up dirt
Bio-descaler RM 511 (order no. 6.290239)
3 x 100 g powder for the cleaning of the boiler.
Round brush with scraper (order no. 2.863-140)
Rubber lip for window nozzle (order no. 6.273-140)
Textile cleaning nozzle (order no. 4.130-390)
Steam turbo-brush (order no. 2.863-159)

Maintenance and Care

DANGER
Always disconnect the mains plug and allow the steam cleaner to cool down before performing any maintenance work.
Descaling the Steam Boiler
As limescale builds up on the boiler walls, we recommend to descale the boiler in the following intervals (RF=reservoir fillings):

Degree of hardness

| mmol/l|

RF

---|---|---
I| soft| 0-1.3| 100
II| medium| 1.3-2.5| 90
III| hard| 2.5-3.8| 75
IV| very hard| >3.8| 50

Note: If you always use the usual commercial istilled water it is not necessary to descale the boiler.
⇒ Disconnect the steam cleaner from the electrical network and let it cool off.
⇒ Empty the water reservoir.
⇒ Remove the complete accessory from the accessory compartments.
⇒ Open the steam boiler seal (A7).
⇒ For this, place the open end of an extension pipe (G1) onto the steam boiler seal, lock it into the guide and unscrew it.

⇒ Completely empty the steam boiler. WARNING
Only use products approved by Kärcher to exclude any damages to the appliance.

⇒ User the KÄRCHER decalcifier sticks (order no. 6.295-047) to decalcify the water. Please follow the dosing instructions on the packaging while using the decalcifying solution.
Caution
Use caution when filling and emptying the steam cleaner. The descaling solution can have an aggressive effect on delicate surfaces.
⇒ Pour the descaling solution into the boiler and allow it to react for approximately 8 hours.
WARNING
Do not screw the steam boiler seal (A7) on the appliance during the descaling. Do not use the steam cleaner as long as there is a descaling agent in the boiler.
⇒ Empty the descaling solution after 8 hours. A small amount of the solution will remain in the boiler. Therefore, you should rinse the boiler two to three times with cold water to remove any residue of the descaler.
⇒ Screw the steam boiler seal (A7) in (close it) using the extension pipe (G1).
⇒ After the refilling with fresh water (see page 21, “Filling the Water Reservoir”) the steam cleaner is ready for use again.
Care of the Accessories
Allow the accessory parts to dry completely before storing them.
⇒ Do not place the floor nozzle (H1), the manual nozzle (E1), and the round brush (D3) onto the bristles during the cooling and drying process to avoid deformation of the bristles.
Note: The floorcloth and the terry cloth cover have been pre-washed and can be used immediately for working with the steam cleaner.
⇒ You can wash dirty floorcloths and terry cloth covers in the washing machine at 60°C. Do not use a liquid softener as this would affect the ability of the clothes to pick up dirt. You may tumble dry the clothes.

Troubleshooting

Often, failures have simple causes and you can do the troubleshooting yourself using the following overview. If you are in doubt or if the failure is not listed here please contact the authorized customer service.
Risk of electric shock!
Repair works may only be performed by the authorized customer service.
Long heating-up time
The steam boiler is decalcified.
⇒ Descale the steam boiler.
No steam
The red low-water indicator lamp blinks
No water in the water reservoir.
⇒ Fill the water reservoir.
A red low-water indicator lamp lights up
No water in the steam boiler. Overheating protection of the pump was triggered.
⇒ Turn off the appliance.
⇒ Fill the water reservoir.
⇒ Turn on the appliance.
The steam switch cannot be pressed anymore
The steam switch is secure with the lock / childproof lock (C3).
⇒ Push the lock (C3) of the steam switch forward.

General Notes

Warranty
The warranty terms published by our competent sales company are applicable in each country. We will remedy possible failures of the appliance free of charge within the warranty period if these failures are attributed to a material or manufacturing error. In case of warranty please contact your dealer or the next authorized customer service and submit the accessories and the proof of purchase. No liability will be accepted if the appliance is incorrectly operated or if the instructions for use are not complied with. Accessories and Spare Parts
Only use accessories and spare parts which have been approved by the manufacturer. The exclusive use of original accessories and original spare parts ensures that the appliance can be operated safely and trouble-free.
Please see the last page for an illustration of the appliance with the order numbers of the individual components.

Specifications

Electrical connection

Voltage| 220-240 V
Kind of current| 1~ 50 Hz
Voltage in the handle| 5 V
Performance data
Heating output| 1800 W
max. operating pressure| 3.5 bar
adm. pressure| 5.7 bar
Heating time per liter of water| 7min
Max. steam quantity| 82 g/min
Dimensions
Water reservoir capacity| 0.95 l
Boiler capacity| 2.0 l
Weight without accessories| 6.5 kg
Width| 340 mm
Length| 420 mm
Height| 315 mm

Register and win!
www.kaercher.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>