LD-TF2.0 Aerial Dropper User Manual
- May 15, 2024
- LD
Table of Contents
LD-TF2.0 Aerial Dropper
Please read this book carefully and keep it properly before using this
product
If you have any questions, please contact the sales personnel
Cautions
- Before use, please confirm whether the drone usage platform can mount this product.
- Follow the installation instructions for safe operation, correctly connect the power supply, and tighten the hanging screws.
- During normal storage, transportation, and use, attention should be paid to moisture-proof, waterproof, dustproof, high temperature resistant, fireproof, and anti-collision.
- When using, it is necessary to follow the rated power and pay attention to voltage matching to avoid damaging this product or your drone equipment.
- If there are quality issues, please do not disassemble the machine without permission to avoid damaging your warranty rights.
- The remote control has set the data, and it is not allowed to initialize the remote control without authorization. The internal data of the remote control cannot be changed, and the consequences will be that the dispenser is not controlled or damaged. Any damage caused by the user changing the data without authorization will be repaired at a cost.
- When using external signal control, the signal line used does not need to provide power supply. Start debugging at the signal stroke setting of plus or minus 20%, gradually increasing to avoid damaging the dispenser.
- If using the DJI expansion module, connect the signal line to the output ports F2 to F8 of the flight control F channel, and then connect the drone to the computer. Rewrite the parameters on the computer parameter adjustment interface. It is recommended to try the journey from 1400 to 1600.
- After use, turn off the power switch of the dispenser in a timely manner, and then turn off the remote control.
Introduction
LD-TF2.0
This product is a customized module used for unmanned aerial vehicles to load and transport items for placement or power wiring purposes. This product has the advantages of light weight, heavy load, fast loading, simple and convenient disassembly, and is suitable for various unmanned aircraft models. Meet the industry’s drone mounting requirements.
Part Name
-
Quick disassembly installation parts
-
Signal antenna
-
Drop hook
-
Power supply interface
-
power switch
-
External signal input port
-
Signal Selection
Installation
Preparations
Before installation and use, the following items need to be prepared: M600
drone, aerial projector, power cord, six channel remote control.
Mount installation
Firstly, take out the dispenser, rotate the quick release part of the
dispenser counterclockwise to loosen it, remove the upper cover of the quick
release part, install the quick release part on the drone mounting rod, and
cover the upper cover and screws of the quick release part. Remove the power
cord, insert the DC end of the power cord into the power DC interface of the
projector, and connect the XT30 plug on the other end of the power cord in
series with the connection head between the M600 landing gear and the fuselage
power supply.
Control And Operation
Remote control operation
Remove the battery cover from the back of the remote control, install four No.
5 AA batteries, pay attention to the positive and negative poles, and then
push the battery cover tightly. Press and hold the power button on the front
of the remote control with both fingers for 2 seconds to turn on the remote
control, and also press and hold for 2 seconds when turning off the remote
control.
Turn on the power switch on the back of the dispenser, and turn the switch to
ON. The red power indicator light remains on.
(When using the remote control, the right switch needs to be in the RC
position; when using an external signal wire control, the dot below the PWM
interface is the direction of the signal wire position, and turning the right
switch to PWM will use an external signal);
After the projector is successfully connected to the remote control control
signal, the RX battery level on the remote control display screen will be
full.
Pick up the remote control and remove the upper left corner control switch to
activate the release hook. When closing the release hook, push the switch up.
SPEC
Specifications
Aerial dropper
Product size| 15573179mm
Outer packaging box| 370268186mm
weight| 311g
Installation method| Quick release type
signal pattern| PWM signal/body output pulse width signal
Power supply mode| Mainframe power supply (supporting voltage 24V)
control mode| Independent remote control
Expand channels| Can support M600 expansion channel function (if you need this
function, please contact sales first)
Controlling Distance| 800m (without obstruction)
Mounted weight| 5KG
Supported platforms| M600 and aircraft with a load capacity of 5-10KG or
above(Standard configuration is M600 model, other models require customized
adapter plates)
Remote control
Overall dimensions| 18082161mm
Weight| 392 g
Input power supply| 6V 1.5AA4
Data output| PS2 interface PPM
Frequency range| 2.4055 – 2.475GHZ
Band width| 500KHZ
Transmitter power| Not higher than 20dBm
Low voltage alarm| Below 4.2V
Charging interface| not have
Length of antenna| 26 mm 2 (dual antenna)
Display method| STN semi transparent positive display, 128×64 dot matrix VA73
- 39mm LED white backlight
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>