LD SYSTEM MAILA SPA Amplifier For Up To Eight Satellites LD Mailaspa User Manual

MAILA SPA Amplifier For Up To Eight Satellites LD Mailaspa
User Manual

YOU MADE THE RIGHT CHOICE!
This device was developed and manufactured under high-quality requirements to ensure many years of trouble-free operation. This is what LD Systems stands for with its name and many years of experience as a manufacturer of high- quality audio products. Please read these operating instructions carefully so that you can quickly and optimally use your new LD Systems product.
You can find more information about LD SYSTEMS on our website WWW.LDSYSTEMS.COM

ABOUT THIS MANUAL

• Read the safety instructions and the entire manual carefully before starting up.
• Observe the warnings on the device and in the operating instructions.
• Always keep the operating instructions within reach.
• If you sell or pass on the device, be sure to also pass on these operating instructions, as they are an integral part of the product.

INTENDED USE

The product is a device for professional audio installation!
The product has been developed for professional use in the field of audio installation and is not suitable for use in households!
Furthermore, this product is only intended for qualified users with specialist knowledge of dealing with audio installations!
Use of the product outside of the specified technical data and operating conditions is considered improper use!
Liability for damage and third-party damage to persons and property due to improper use is excluded!
The product is not suitable for:

• People (including children) with reduced physical, sensory or mental abilities or lack of experience and knowledge.
• Children (Children must be instructed not to play with the device).

EXPLANATIONS OF TERMS AND SYMBOLS

1. DANGER: The word DANGER, possibly in combination with a symbol, refers to directly dangerous situations or conditions for life and limb.
2. WARNING: The word WARNING, possibly in combination with a symbol, refers to potentially dangerous situations or states of life and limb.
3. ATTENTION: The word CAUTION, possibly in combination with a symbol, refers to situations or conditions that can lead to injuries.
4. DANGER: The word ATTENTION, possibly in combination with a symbol, refers to situations or states that can lead to damage to property and/or the environment.

This symbol indicates hazards that can cause an electric shock.
This symbol indicates dangerous spots or dangerous situations.
This symbol indicates danger from hot surfaces.
This symbol indicates danger from high volumes.
This symbol indicates supplementary information on the operation of the product.
This symbol denotes a device that does not contain any user-serviceable parts.

SAFETY INSTRUCTIONS

DANGER:

1. Do not open or modify the device.

2. If your device is no longer working properly, liquids or objects have gotten inside the device, or the device has been damaged in any other way, switch it off immediately and disconnect it from the power supply. This device may only be repaired by authorized specialist personnel.

3. For devices of protection class 1, the protective conductor must be connected correctly.
   Never interrupt the protective conductor. Protection class 2 devices do not have a protective conductor.

4. Ensure that live cables are not kinked or otherwise mechanically damaged.

5. Never bypass the device fuse.

WARNING:

1. The device must not be put into operation if it shows obvious signs of damage.
2. The device may only be installed in a voltage-free state.
3. If the power cord of the device is damaged, the device must not be put into operation.
4. Permanently connected main cables may only be replaced by a qualified person.

DANGER:

1. Do not operate the device if it has been exposed to severe temperature fluctuations (e.g.
   after transport). Humidity and condensation could damage the device. Do not switch on the device until it has reached the ambient temperature.

2. Make sure that the voltage and frequency of the main supply correspond to the values indicated on the device. If the device has a voltage selector switch, do not connect the device until this is set correctly. Only use suitable power cords.

3. To disconnect the device from the mains at all poles, it is not enough to press the on/off switch on the device.

4. Ensure that the fuse used corresponds to the type printed on the device.

5. Make sure that appropriate measures against overvoltage (e.g. lightning) have been taken.

6. Note the specified maximum output current on devices with a power-out connection.
   Make sure that the total power consumption of all connected devices does not exceed the specified value.

7. Only replace pluggable main cables with original cables.

DANGER:
1. Danger of suffocation! Plastic bags and small parts must be kept out of the reach of people (including children) with reduced physical, sensory or mental abilities.
2. Danger from falling! Make sure the device is installed securely and cannot fall. Only use suitable tripods or attachments (especially for fixed installations). Make sure accessories are properly installed and secured. Make sure that the applicable safety regulations are observed.

WARNING:

1. Only use the device in the manner intended.
2. Only operate the device with the accessories recommended and intended by the manufacturer.
3. During installation, observe the safety regulations applicable in your country.
4. After connecting the device, check all cable routes to avoid damage or accidents, e.g. B. to avoid tripping hazards.
5. Be sure to observe the specified minimum distance to normally flammable materials!
   Unless this is explicitly stated, the minimum distance is 0.3 m.

ATTENTION:

1. There is a risk of jamming with moving components such as mounting brackets or other moving components.
2. In the case of devices with motor-driven components, there is a risk of injury from the movement of the device. Sudden device movements can lead to startling reactions.

DANGER:

1. Do not install or operate the device near radiators, heat registers, stoves, or other heat sources. Make sure that the device is always installed in such a way that it is sufficiently cooled and cannot overheat.
2. Do not place any sources of ignition such as burning candles near the device.
3. Ventilation openings must not be covered and fans must not be blocked.
4. Use the original packaging or packaging provided by the manufacturer for transport.
5. Avoid shock or shock to the device.
6. Observe the IP protection class and the environmental conditions such as temperature and humidity according to the specification.
7. Devices can be continuously developed. In the event of deviating information on operating conditions, performance or other device properties between the operating instructions and the device labeling, the information on the device always has priority.
8. The device is not suitable for tropical climate zones and for operation above 2000 m above sea level.

ATTENTION:
Connecting signal cables can result in significant noise interference. Make sure that devices connected to the output are muted during plugging. Otherwise, noise levels can cause damage.

ATTENTION HIGH VOLUMES WITH AUDIO PRODUCTS!
This device is intended for professional use.
The commercial operation of this device is subject to the applicable national regulations and guidelines for accident prevention.
Hearing damage due to high volumes and continuous exposure: The use of this product can generate high sound pressure levels (SPL) which can cause hearing damage. Avoid exposure to high volumes.

SIGNAL TRANSMISSION VIA RADIO (e.g. W-DMX or audio radio systems, Bluetooth):
The quality and performance of wireless signal transmissions generally depend on environmental conditions.

Influence on the range and signal stability, for example:

• Shielding (e.g. masonry, metal structures, water)
• High radio traffic (e.g. strong W-LAN networks)
• interference
• Electromagnetic radiation (e.g. LED video walls, dimmers)

All range specifications refer to free field use with visual contact without interference!

The operation of transmitters is subject to official regulations. These can vary from region to region and must be checked by the operator before commissioning (e.g. radio frequency and transmission power).

WARNING:
Devices with wireless signal transmission are not suitable for operation in sensitive areas in which radio operation can lead to possible interactions. These include, for example:

• Hospitals, health centers, or other healthcare facilities that perform patient treatments with specialized staff and equipment.
• Class I, II, and III hazardous areas
• restricted areas
• military facilities
• airplanes or vehicles
• Areas where cell phone use is prohibited

NOTES FOR PORTABLE INDOOR DEVICES

1. Temporary operation! Event equipment is basically only designed for temporary operation.
2. Continuous operation or permanent installation can lead to impairment of the function and premature aging of the devices.

SCOPE OF DELIVERY

Remove the product from the packaging and remove all packaging material.
Check the completeness and integrity of the delivery and please notify your distributor immediately after purchase if the delivery is not complete or damaged.
The product comes with:

• 1x LD MAILA SPA amplifier module for MAILA satellites
• 1x Power cord
• 1x M10 eyebolt
• Operating instructions

PROPERTIES

MAILA SPA is the only MAILA module without integrated loudspeakers – and yet an integral part of the MAILA concept. Its versatility can already be guessed at when looking at the range of MAILA sets: The MAILA SPA amplifier module is used both in the smallest MAILA-S ground stack set and in the large MAILA XL version with flown arrays.

MAILA SPA is an amplifier module in an elegant unibody aluminum design with an integrated 1.25 kW power amplifier with SysCore® DSP for controlling up to eight MAILA  SAT satellites. Via the SmartLink+® system, the satellites can be easily plugged in and wirelessly supplied with an audio signal.
In addition, SmartLink+ ® enables the independent determination of the installed satellites for either automatic or manual DSP processing. As with the MAILA COL column module, MAILA SPA allows users to implement ground stack configurations with a distance pole (supplied in the MAILA S Set) as well as flown systems with the EasyMount+  ® mounting adapter.

With LogoLink®, LD Systems maila has added another innovation. Via the free MAILA app (iPadOS), every MAILA system can be adapted quickly, easily, and in detail and wirelessly supplied with software updates. Once connected, the app automatically detects the existing MAILA components and enables the system to be optimally set up in advance and during an event. The highlight: The required wireless antennas are invisibly integrated into the LD logo of the MAILA SPA.

MAILA APP (iPadOS)
The MAILA app for iPadOS is available free of charge in the App Store.

CCONSTRUCTION AND TRANSPORT ASSEMBLY

DANGER:
Always place the speaker system in a suitable place on a sufficiently load- bearing, flat, and horizontal surface. Make sure that the speaker system cannot fall off the edge of a  stage (e.g. due to vibration).
DANGER:
Overhead assembly requires extensive experience, including calculating workload limits, installation material used, and regular safety reviews of all installation materials and equipment. If you do not have these qualifications, do not try to do an installation yourself, but use the help of professional companies. There is a risk that incorrectly assembled and secured devices will come loose and fall down. As a result, people can be seriously injured or killed.

Mount the amplifier module on the distance pole: Plug the amplifier module in the desired beam direction from above onto the LD MAILA DB distance pole already mounted on the subwoofer. Unintentional twisting of the amplifier module is prevented by a tongue and groove principle.

To mount the optionally available EasyMount+ flight bracket on the amplifier module, insert all three steel hooks of the flight bracket into the corresponding holding sockets of the amplifier module. Now slide the entire flight bracket towards the back of the case. When mounting the flight bar, make sure that the two spring-loaded safety lock bolts snap completely into the safety holes provided for this purpose. Check the correct functioning of the locking bolts before each installation. To loosen the connection, both locking bolts must be pulled upwards at the same time for safety reasons (two-hand unlocking).

Amplifier module LD MAILA SPA: The optimal hanging point for truss mounting is displayed after entering the corresponding data in the SPLAY ANGLES menu item under  PICK. On the retaining rail of the flight bar, there are corresponding markings.
Set up the displayed suspension point before mounting the flight bracket with the amplifier module on a traverse.

There are two M10 threads on the back of the MAILA SPA amplifier module (see markings). Use one of them to secure the amplifier module when mounting the crossbar.  Remove the inserted blind screw using a suitable tool. An M10 eyebolt is included in the scope of delivery of the MAILA SPA. Screw the eyebolt into the now-free thread and make sure it is firmly fixed. Use a suitable safety rope to secure the amplifier module and also take into account the total weight of the satellite speakers mounted on the amplifier module.

NOTE
The satellites do not need to be secured by a safety cable as the SmartLink+ connection meets the criteria for inherent safety.
However, if desired, the satellite speakers can be secured to the amplifier module using the second M10 thread.

CONNECTIONS, CONTROLS, AND DISPLAY ELEMENTS

|
---|---

1 POWER INPUT
PowerCON TRUE1 power input jack. A suitable power cord is included
2 INPUT
Balanced line input with lockable, female 3-pole XLR socket.
3 THRU
Balanced line output for forwarding the line input signal (male 3-pole XLR socket).
4 TRIPOD FLANGE
Tripod flange for the distance pole LD MAILA DB.
5 HOLDING BUSHES
Holding sockets for the EasyMount+ flight bracket LD MAILA TMB.
6 LC-DISPLAY
Multifunctional graphic LC display with lighting.
7 PUSH TO ENTER / HOLD TO MUTE
Rotary push encoder for navigating the main menu and submenus and adjusting system settings.
Select the individual menu items in the main menu and in the submenus by rotating the encoder and confirming the selection by pressing the encoder. Change a numerical value or status in a menu item by rotating the encoder and confirm the change by pressing the encoder. To move up one level in the menu structure, select the arrow symbol < and confirm the selection.
Press the encoder for about 2 seconds to mute the amplifier module and again for about 2 seconds to unmute it.
8 LEDS TO INDICATE DEVICE STATUS
PWR – (Power)
The white indicator LED lights up when the device is properly plugged in and turned on.
SIG – (Signal)
The white indicator LED lights up when there is an audio signal on the device.
LIMIT – (Limiter)
The yellow indicator LED lights up when the amplifier module is operating in the upper limit range.
A short illumination of the LED is uncritical. To protect the system, an excessive signal level is gently lowered by the integrated limiter. If the limiter LED lights up longer or permanently, reduce the volume level.
PROT – (Protect)
The red indicator LED lights up if the amplifier module is overloaded or overheated. The amplifier module is automatically muted. After reaching normal operating conditions,  the device returns to normal operating mode after a few minutes.
9 PUSH TO UNLOCK SAT
At the rear top of the amplifier module is the release button for releasing a mounted satellite speaker.

VENTS

To avoid damage to the device, do not cover the vents on the back and ensure that air can circulate unhindered.

SERVICE

HINTS

• During the power-on process, all settings, such as VOLUME and EQUALIZER, are charged as they were set before the speaker column was switched off. After a short time,  the loudspeaker column is ready for operation
• After about 30 seconds without input via rotary push encoder, the display system leaves lower levels in the menu structure and the main display with the selection VOLUME is automatically displayed.

DISPLAY MAIN DISPLAY
In normal operation, the main display is activated, showing the main menu, the set delay, and the number of satellites used. The Bluetooth status, the volume level (LVL), and the gain (VOL) are displayed graphically.
If the top segment of the level meter glows red, this signals that the input stage is operating above the distortion limit (clip). Reduce the output level of the feeder (e.g. mixing console) until the clip segment is no longer lit and the amplifier module plays audio signals without distortion.
VOLUME
To set the level of the amplifier module, select VOLUME from the main menu confirm, then set the desired value from -40 dB to +10 dB and confirm again.

Mute: Press the encoder for about 2 seconds to mute the amplifier module and again for about 2 seconds to unmute (at all menu levels).

SPLAY ANGLES
Mounting on distance pole:

To enable the automatic calculation of the optimal spreading angles of the satellites, the rotation of the display must be set correctly. ROTATION menu item, status: standing The number of satellite speakers used is automatically detected by the module electronics. To enter the relevant data of the audience area and the height at the measuring point,  select SPLAY ANGLES in the main menu confirm, then select the corresponding submenu item and confirm again.
For truss mounting, enter under Sat. Height has measured as the height of the top edge of the top satellite from the listener’s stand area and the distance from the array system to the rearmost audience row (coverage) in meters. Under Seated enter a standing (Seated OFF) or seated audience (Seated ON).
Now the optimal spreading angles for each satellite and the suspension point PICK for the EasyMount+ flight bracket are automatically displayed. To exit the menu level, select the arrow icon and confirm the selection.
The spreading angles are set manually on the satellite speakers. The hanging point of the EasyMount+ flight bracket is also set up manually. The correct setting of the displayed spreading angle and the hanging point is a prerequisite for the optimal sound distribution in the specified audience area.

TRUSS MOUNTING:

****In order to enable the automatic calculation of the optimal spreading angles of the satellites and the optimal suspension point of the EasyMount+ flight bar (for truss mounting), the rotation of the display must be set correctly.
Menu item ROTATION, Status: flying

The number of satellite speakers used is automatically detected by the module electronics. To enter the relevant data of the audience area and the height at the measuring point,  select SPLAY ANGLES in the main menu confirm, then select the corresponding submenu item and confirm again.

For truss mounting, enter under Sat. Height is measured as the height of the top edge of the top satellite from the listener’s stand area and the distance from the array system to the rearmost audience row (coverage) in meters. Under Seated enter a standing (Seated OFF) or seated audience (Seated ON).
Now the optimal spreading angles for each satellite and the suspension point PICK for the EasyMount+ flight bracket are automatically displayed. To exit the menu level, select the arrow icon and confirm the selection.

The spreading angles are set manually on the satellite speakers. The hanging point of the EasyMount+  flight bracket is also set up manually. The correct setting of the displayed spreading angle and the hanging point is a prerequisite for the optimal sound distribution in the specified audience area.

EQUALIZER
The integrated DSP (Digital Signal Processor) has a powerful 10-band fully parametric equalizer. Select EQUALIZER from the main menu and confirm the selection.

The functionality of the equalizer bands 1 and 10 can be set either as fully parametric or as low-shelf (band 1, LS) or hi-shelf (volume 10, HS).

To set the frequency in Hertz under FREQ, the Q-factor or the functionality of bands 1 and 10 under Q and
the gain in dB under GAIN select the corresponding column in the desired equalizer band (NR 1 – 10),
confirm, set the value as desired and confirm again. The selected value is displayed in white.
The EQ bands can be disabled individually by selecting and confirming the band number. Instead of a
checkmark icon, an X is now displayed and the values in the corresponding volume appear grayed out.
To activate the tape, select and confirm again.
The entire equalizer can be disabled by selecting the EQ line confirming, then selecting OFF and confirming again. All values in the equalizer are now grayed out. To activate the equalizer, select ON and confirm. To exit the menu level, select the arrow icon and confirm the selection.

DELAY
To delay the audio signal, select DELAY to confirm, then select the desired submenu item and confirm again. The value or status can now be set as desired, confirm each entry.

temperature unit
TEMP. UNITº| ºC| Temperature unit Celsius
°F| Temperature unit Fahrenheit

To exit the menu level, select the arrow icon and confirm the selection.

POLARITY
To set the polarity of the audio signal, select POLARITY confirms, then select the desired status and confirm the selection.

ROTATION
To set the rotation of the display, select ROTATION confirms, then select the desired status and confirm the selection.

****In order to enable the automatic calculation of the optimal spreading angles of the satellites and the optimal suspension point of the EasyMount flight bracket (for truss mounting), the rotation of the display must correspond to the mounting type.

• Mounting on distance pole: ROTATION standing
• Truss mounting (180° rotation): ROTATION flying

SETTINGS
To access the System Preferences menu, select SETTINGS and confirm the selection. Then select the desired submenu item and confirm the selection.

Enter PIN
code to LOCI| Protect the amplifier module from accidental and unauthorized operation by activating the lock function.
Enter a 4-digit PIN and confirm the entry.
Access can now only take place after entering the PIN.
Reset PIN: Press and hold the encoder when powering on.
BLUETOOTH| OFF| Bluetooth disabled.
ON| Bluetooth enabled, allows access to the system via a tablet app.
DISPLAY| Brightness| Adjust the display brightness from 10% to 100%.
Screensaver| active| Deactivation of the display illumination after about 1
a minute without input via rotary push encoder.
inactive| Display lighting permanently on.
RESET| FACTORY DEFAULT RESET| | Restore factory settings: Select and confirm RESET.

(the illustrations in the device menu may vary slightly depending on the software version)

MAILA APP

Download the MAILA app, which is available free of charge in the App Store, onto your tablet and install it. Activate Bluetooth in the system settings of the active MAILA  components. Also, activate Bluetooth in the system settings of your tablet and start the MAILA app. The MAILA components with activated Bluetooth within range are now automatically displayed in the MAILA app after a short time.

FIRMWARE UPDATE

Check with the help of the MAILA app whether new firmware is available for your device. Start the update procedure via MAILA App. Make sure that there is a stable wireless connection between the device and tablet and do not turn off the device or tablet before the update procedure is complete. Aborting the update procedure may cause the device to malfunction. The MAILA app for IOS is available free of charge in the App Store.

INDICATION-LED

The amplifier module has a white display LED on the front behind the front grille. This can be activated to easily identify the amplifier module with the help of the MAILA app.  The MAILA app for IOS is available free of charge in the App Store.

OPTIONAL ACCESSORIES

LDMAILAFC1 (Flightcase for 4x SAT, 1x SPA, 1x distance pole)
LDMAILAFC3 (Flightcase for 8x SAT, 1x SPA, 1x EasyMount+)
LDMAILADB (distance pole)
LDMAILATMB (EasyMount+ flight bracket)

CARE, MAINTENANCE AND REPAIR

In order to ensure the proper functioning of the device in the long term, it must be regularly maintained and maintained if necessary. The need for care or maintenance depends on the intensity and environment of use. We generally recommend a visual inspection before each commissioning. Furthermore, we recommend every 500 operating hours, or in the case of lower intensity of use at the latest after one year, to carry out all the care measures mentioned below and applicable. In the case of defects that are due to inadequate care, there may be limitations on the warranty claims.

CARE (CAN BE CARRIED OUT BY THE USER)

WARNING! Before any maintenance measures, the power supply and, if possible, all device connections must be disconnected.
HINT! Improper care can lead to impairment of the device up to destruction.

1. Housing surfaces must be cleaned with a clean, damp cloth. Care must be taken to ensure that no moisture can penetrate into the device.
2. Air inlet and outlet openings must be regularly cleaned of dust and dirt. In the case of the use of compressed air, care must be taken to prevent damage to the device (e.g. fans must be blocked in this case).
3. Cables and plug-in contacts must be cleaned regularly and cleaned of dust and dirt.
4. In general, no cleaning agents or agents with a grinding effect may be used for care, otherwise, the surface quality is to be expected to be impaired.
5. Equipment must generally be stored dry and protected from dust and dirt.

MAINTENANCE AND REPAIR (ONLY BY QUALIFIED PERSONNEL)

DANGER! There are live components in the device. Even after disconnection of the mains connection, the residual voltage may still be present in the device, e.g. due to charged  capacitors
HINT! There are no modules in the device that can be serviced by the user.
HINT! Maintenance and repair measures may only be carried out by specialist personnel authorized by the manufacturer. If in doubt, contact the manufacturer.
HINT! Improperly performed maintenance work may affect the warranty claim.

DIMENSIONS (mm)

SPECIFICATIONS

DSP Characteristic
Bit-depth AD/DA converter| 24-bit
Sampling frequency| 48 kHz
Bluetooth
Bluetooth version| 4.2
Bluetooth transmission power| 9 dBm
Bluetooth frequency range| 2402-2480 MHz

DISPOSAL

Packaging:

1. Packaging can be fed into the recycling cycle via the usual disposal routes.
2. Please separate the packaging in accordance with the disposal laws and recyclable material regulations in your country.

Device:

1. This device is subject to the European Directive for Waste Electrical and Electronic Equipment in the current version. WEEE Directive Waste Electrical and Electronical Equipment. Old appliances and batteries do not belong in the household waste. The old equipment or batteries must be disposed of via an approved disposal company or a municipal disposal facility. Please note applicable regulations in your country!
2. Observe all disposal laws applicable in your country.
3. As a private customer, you will receive information on environmentally friendly disposal options from the dealer from whom the product was purchased or from the relevant regional authorities.

Batteries and rechargeable batteries:

1. Batteries and rechargeable batteries do not belong in household waste. Batteries and accumulators must be disposed of via an approved disposal company or a municipal
   disposal facility.

2. Observe all disposal laws and regulations applicable in your country.

3. As a private customer, you will receive information on environmentally friendly disposal options from the dealer from whom the product was purchased or from the relevant regional authorities.

4. Devices with batteries or rechargeable batteries that cannot be removed by the user must be handed in at a collection point for electrical appliances.

MANUFACTURER DECLARATION

MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY
Adam Hall GmbH, Adam-Hall-Str. 1, D-61267 Neu Anspach / Email Info@adamhall.com / +49 (0)6081 / 9419-0.
For our current warranty terms and limitation of liability see:
https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS- DECLARATIONS_LD_SYSTEMS.pdf.
In the event of service, please contact your sales partner.

UKCA- CONFORMITY
Hereby, Adam Hall Ltd. declares that this product meets the following guidelines (where applicable)
Electrical Equipment (Safety) Regulations 2016
Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulation 2012 (SI 2012/3032)
Radio Equipment Regulations 201 7(SI 2016/2015)

UKCA- DECLARATION OF CONFORMITY
Products that are subject to Electrical Equipment(Safety)Regulation 2016, EMC Regulation 2016 or RoHS
Regulation can be requested at info@adamhall.com. Products that are subject to the Radio Equipments Regulations 2017 (SI2017/1206) can be downloaded from
www.adamhall.com/compliance/

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference, and
   (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,  pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

EU DECLARATION OF CONFORMITY
Adam Hall GmbH hereby declares that this radio system type complies with Directive 2014/53/EU.
The full text of the EU declaration of conformity is under the following
Internet address available: www.adamhall.com/compliance/

Misprints and mistakes, as well as technical or other changes are reserved!to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

EU DECLARATION OF CONFORMITY
Adam Hall GmbH hereby declares that this type of radio equipment complies with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available below Internet address available: www.adamhall.com/compliance/

Printing errors and mistakes, as well as technical or other changes, are reserved!

Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany
Phone: +49 6081 9419-0 | adamhall.com
Adam Hall Ltd. | The Seedbed Business Centre | SS3 9QY Essex | UK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>