Uthfy JTF-14-R Tower Fan with Remote User Manual
- May 15, 2024
- Uthfy
Table of Contents
ELECTRONIC CONTROL TOWER FAN
OWNER’S MANUAL
Model No. JTF-14-R
Dear customer:
First of all, thank you for purchasing and using our Tower Fan. In order for you to use our products better, please read this instruction manual carefully before use, and for the safety of you and your family, please be sure to abide by the relevant regulations in the manual. In order to protect your legitimate rights and interests, please keep the manual, warranty card and purchase invoice properly. If you have any questions during use, please contact us in time. Thank you again for choosing our products, he will make your life more comfortable and warm!
I. Schematic diagram of product parts
DIGITAL TYPE
- control panel
- Head cover
- Trim panel
- Air outlet
- Left shell
- base
- Handle
- Air inlet
- Right shell
- power cord
REMOTE CONTROL
MECHANICAL TYPE
- Knob switch
- Head cover
- Trim panel
- Air outlet
- Left shell
- base
- Handle
- Air inlet
- Right shell
- power cord
II. Technical parameter
MODEL NO.
| RATED VOLTAGE| RATED FREQUENCY| RATED POWER
---|---|---|---
JTF-14| 120V~| 60Hz|
60W
JTF-14-R
| 120V~| 60Hz|
60W
Notes: If the above parameters are changed, please refer to the nameplate of product.
III. Product circuit diagram
MECHANICAL TYPE
DIGITAL TYPE
IV. Instructions for use of the operation panel
Electronic panel operation
OPERATION INSTRUCTIONS
This product is intended for indoor residential and office use only, not for industrial or other commercial applications, Use only with electrical wiring that is in good working order and that meets applicable codes and regulations. If you have any questions about whether your wiring is adequate, consult a qualified electrician.
Buttons
On/off button: press the on/off button to switch the fan on or off.
Speed button: press the button to change the speed between low-> medium->
high. Default speed is low speed.
Mode button: press the button to change fan mode between normal mode
-natural mode-> sleep mode Sleep mode: lowers speed every 30 minutes and then
stays at the lowest speed. Natural mode: the speed changes randomly
Swing button: press the button to activate or deactivate
swinging/oscillation. The fan moves slowly from left to right and back again.
Oscillation works in all fan modes.
timer button: Press this key set timer, step 1 hours, max 10 hours.
Screen off button: lightly press this key to turn off all indicator
lights in the power on state. (Note: when the screen is off Operating other
function keys will terminate the screen shutdown function).
Battery
Before first use: Pull the protective film to remove it. The remote control is
now ready for use.
To replace the battery: open the battery compartment on the back of the remote
control and replace the used battery with a new one. Battery type:CR2025
Mechanical panel operation
Knob switch gear function: turn the gear knob to turn off → low wind speed → medium wind speed → high wind speed → off → low wind speed swing → medium wind speed swing → high wind speed swing
V. Operation and usage
Before beginning installation of product , make sure all parts are present.
compare parts with package content list and hard ware contents list. If any
part is missing or damaged , do not attempt to assemble, install or operate
the product.
ASSEMBLY INSTRUCTION
-
Assemble left and right base together.
Note: Let the power cord through the hole of the base when assembling. -
Drive 4 screws in the accessories bag into the hole on the base and fix the base on the main body.
-
Put the product on a stable, smooth ground before using.
Base Screws Fan
VI. Storage and Maintenance
- When not in use, first turn off the power and pull out the plug.
- For cleaning and maintenance, make sure that the fan is disconnected from the power supply before removing the protective cover!
- After maintenance and cleaning, please put all parts into the packing box according to the original packing order.
- Store it in a place without direct sunlight and less humidity.
- Please do not place it near fire or flammable materials.
- When cleaning, please wipe with a soft cloth soaked in water or kitchen detergent, and then wipe with a soft dry cloth; do not use hard objects to wipe the surface.
- Do not use Tianna water, alcohol, alkaline detergent, decontamination powder, volatile agent, toluene or chemical rags for cleaning to prevent the cooling fan from discoloration and corrosion.
- If there is a slight abnormal sound or smell when using it for the first time, it is a normal phenomenon, please use it with confidence.