AQUA MEDIC DC Runner 800 Ocean Clear Seaflower Instruction Manual

: September 12, 2024
: AQUA MEDIC

Table of Contents

AQUA MEDIC DC Runner 800 Ocean Clear Seaflower
1. Included in delivery
2. Safety instructions
3. Start-up
4. Warranty conditions
Specifications:
FAQ:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AQUA MEDIC DC Runner 800 Ocean Clear Seaflower

INSTRUCTION MANUAL

AB Aqua Medic GmbH
Gewerbepark 24, 49143 Bissendorf, Germany

Compact fleece roll filter with high cleaning performance

The fleece filter of the Ocean Clear is extremely effective at filtering out coarse dirt particles, suspended particles and other organic waste from the water. This helps to minimize the formation of nitrate and phosphate while retaining important trace elements.

Suitable for salt- and freshwater aquaria with a water volume of up to 850 litres.
For operation with an additional pump, we recommend our DC Runner 800 or 1000.
Only for operation inside the filter tank. Dimensions (l x w x h) app.: 180 x 160 x 325 mm

1. Included in delivery

– Ocean Clear housing with filter insert
– Ocean Clear Fleece Roll (approx. 40 m)
– Controller
– Power supply unit: In: 100 – 240 V AC / 50/60 Hz
Out: 12 V/ 1 A DC
– Float switch
– Motor

2. Safety instructions

– When working in the aquarium, always disconnect all units from the power supply system before putting your hands into the water. Connect all units to the mains via a residual current device with a maximum residual current of 30 mA.
– Connection to pumps other than those mentioned in the instructions is not permitted.
– Suitable for indoor use only.
– Protect the controller from moisture (humidity < 80%), splash water and condensation.
– We recommend forming drip loops with the cables to prevent any water running along the cables from getting into sockets.
– The electrical data of the Ocean Clear must match the data of the power supply unit used (12 V DC). This data can be found on the rating plates.
– Not suitable as a toy for children.

3. Start-up

3.1. Assembly

Fig. 1: Ocean Clear housing and filter insert

1. Suspensions
2. Screws
3. Mounting bracket
4. Rubber plug
5. Float switch with bracket and mounting screw
6. Sealing cap for pump assembly
7. Take-up reel
8. Fleece holder
9. Fleece roll
10. Motor
11. Connecting rod
12. filter housing
13. Filter insert

The suspensions (1) must be mounted on the filter housing (12) according to the desired position in the filter tank. You can attach the filter with the narrow side, in which case the suspensions are screwed directly to the housing, or with the wide side. In this case, the two mounting brackets (3) are first screwed to the filter housing using the countersunk screws. The suspensions are then attached to these. The filter should be immersed approx. 9 – 10 cm into the water so that sufficient space remains up to the float switch (Fig. 2). The edge of the filter housing should be lower than the glass edge of the filter basin so that no water can run out of the filter housing next to the filter basin in the event of a defect. It is also important to ensure that the fleece rolls do not rest against a glass edge (Fig. 7). Bear in mind that the roll will be slightly thicker on the reel than when unused. Any threaded openings on the filter housing that are not required are sealed with the rubber plugs (4) supplied.

Fig. 2: Mounting the float switch (height adjustable using a screw)

Fig. 3: Fleece mounting

First remove the adhesive strip from the fleece. Then place the fleece around the inner tube (Fig. 3, No. 1). The glued-on guide rail is then positioned between the curved fleece. Now, slide the clamping rail (Fig. 3, No. 2) over the tube with the fleece. The fleece is not glued tightly so that it can be removed more easily later. Then wind up the fleece a little more (note the direction, see Fig. 1). Work as precisely as possible so that it winds up straight later.

The fleece roll and winding spool with the motor inserted are mounted as shown in Fig. 1. The filter insert is held together at the highest point with a connecting rod.

Fig. 4: Ocean Clear with DC Runner 1000 (not included)

The Ocean Clear can be operated completely independently with its own pump (Fig. 4). There is a black sealing cap on the side of the filter housing (Fig. 1, No. 6). It can be cut open in a cross shape along the markings (Fig. 5) using a sharp cutter knife. An Aqua Medic DC Runner 800 or 1000 without hose connection is inserted directly with its thread.

Fig. 5: Sealing cap for pump assembly

Fig. 6: Inlet via drain pipe from the aquarium overflow (max. 32 mm pipe diameter)

However, the Ocean Clear can also be connected to an aquarium overflow (see Fig. 6). The inlet pipe then protrudes into the narrow inlet chamber. The flow rate should not exceed 2,000 litres per hour, although this depends on the filter installation. The flow rate should not be confused with the flow rate of the return pump used. In an aquarium with an under cabinet filter and overflow, the maximum capacity of the pump is usually considerably higher than the effective inflow to the filter due to the pipework and the difference in height.

Fig. 7: The fleece roll must not be blocked by the edge of the filter basin.

The higher the filter is mounted, the more space remains at the top. Please note that as the fleece becomes increasingly dirty, the water level in the filter housing rises and water may spill over the edge of the filter container if the flow rate is high. In this case, lower the float switch (Fig. 2) slightly.

To insert the filter insert with the mounted fleece roll into the filter container, pull the side disc with the float switch attached to it upwards a little. Removal is carried out in reverse order.

If the fleece is completely dirty and wound up, remove it from the take-up reel by first pulling the motor and then the reel out of the wound-up fleece to the side.

A completely soiled and wound fleece is removed from the take-up reel by first switching off the motor and then pulling the reel out of the wound fleece to the side.

3.2. Operation

Fig. 8: Controller

1. Operating indicator light
2. Motor operation
3. Alarm/pause
4. Operating mode HIGH: complete fleece in the filter housing is replaced
5. Operating mode ECO: fleece in the filter housing is only partially replaced
6. Pause
7. Mode selection: High or ECO
8. Manual control: press first time: motor on/ press second time: motor off
9. 12 V power supply connection
10. motor connection
11. Socket for float switch

Operating indicator light (Fig. 5, No. 1):
Green light on – DC power supply is working
Green light off – DC power not available
Motor operation LED (Fig. 5, No. 2):
Motor operation green light, long green light – indicates that the motor is running
LED: alarm/pause (Fig. 5, No. 3):
1. Red light is always on – pause
2. Red light flashes – pause. Motor operation is resumed after 10 minutes
3. Red light not illuminated – normal operation
LED mode indicator (Fig. 5, No. 4 and 5):
HIGH mode: fleece is completely replaced (high load, higher fleece consumption)
ECO mode: fleece is only partially replaced (normal load, lower fleece consumption, more optimal fleece utilisation)
Key functions:

MODE (Fig. 5, No. 7): selection button for the operating mode. The selected operating mode is indicated by the HIGH (Fig. 5, No. 4) or ECO (Fig. 5, No. 5) LEDs.

Arrow (Fig. 5, No. 8): manual motor operation. After pressing the button, the motor starts in manual mode. After pressing the button again, it stops and runs again in the selected mode.
The action runs through accordingly and the closing time action is not executed in manual mode.

Pause (Fig. 5, No. 6): press once: motor stops until pause button is pressed again. Alarm confirmation.

Press twice: pause for 10 minutes before resuming work (LED flashes).

Press three times: return to normal working mode.
– Alarm functions:

Alarm motor protection switch: motor operation LED and alarm/pause LED flash alternately. The buzzer emits a rapid alarm tone and the motor stops at the same time.

Motor short-circuit alarm: ll indicator lights flash alternately for 1 second, the buzzer emits a rapid alarm tone and the motor stops at the same time.

Water level error alarm: LED alarm/pause flashes and the buzzer emits an alarm sound (beep), indicating that a foreign object is blocking the cloth rewinder, the water level is abnormal or the filter cloth is exhausted.
Cancelling the alarm: press the mode selection button for two seconds.

4. Warranty conditions

AB Aqua Medic GmbH grants the first-time user a 24-month guarantee from the date of purchase on all material and manufacturing defects of the device. Incidentally, the consumer has legal rights; these are not limited by this warranty. This warranty does not cover user serviceable parts, due to normal wear & tear. The original invoice or receipt is required as proof of purchase. During the warranty period, we will repair the product for free by installing new or renewed parts. This warranty only covers material and processing faults that occur when used as intended. It does not apply to damage caused by transport, improper handling, incorrect installation, negligence, interference or repairs made by unauthorized persons. In case of a fault with the unit during or after the warranty period, please contact your dealer. All further steps are clarified between the dealer and AB Aqua Medic. All complaints and returns that are not sent to us via specialist dealers cannot be processed. AB Aqua Medic is not liable for consequential damages resulting from the use of any of our products.

AB Aqua Medic GmbH – Gewerbepark 24 – 49143 Bissendorf/Germany

– Technical changes reserved – 05/2024/v1

Specifications:

Brand: Ocean Clear
Manufacturer: AB Aqua Medic GmbH
Power Output: 12 V / 1 A DC
Country of Origin: Germany

FAQ:

Q: Can I use a different pump with the Ocean Clear?

A: The Ocean Clear is designed to work with Aqua Medic DC Runner pumps. It is recommended to use these pumps for optimal performance.

Q: How often should I replace the filter fleece?

A: The frequency of filter fleece replacement depends on the aquarium size and stocking levels. It is recommended to monitor the condition of the fleece regularly and replace it when it becomes dirty or clogged.