BRASSTECH 034 Grab Bar Instruction Manual
- May 15, 2024
- BRASSTECH
Table of Contents
BRASSTECH 034 Grab Bar
Product Information
Specifications
- Brand : Newport Brass
- Model : INS-2400 EN-4575 REV
- Material: Stainless Steel
- Color: Silver
- Length: Standard lengths available
Product Usage Instructions
Mounting Instructions
- Remove the Grab Bar and parts from the package.
- Locate wood wall studs using a stud finder.
- Attach Mounting Flange onto the Grab Bar and tighten the M5 setscrew.
- Place the Grab Bar over the wall stud at the desired position.
- If installing over ceramic tiles, place masking tape on the mounting area before marking the hole location.
Safety Precautions
Ensure that both ends of the grab bar are installed into wood wall studs for proper support. Exercise caution when drilling into the wall to avoid damaging electrical wiring or plumbing located behind the wall. If unsure about installation, consider hiring a qualified professional for installation.
Cleaning and Maintenance:
Regularly clean the grab bar with a mild soap and water solution to maintain its appearance. Inspect the grab bar periodically for any signs of damage or looseness. Do not use if any damage is found; contact an authorized dealer for assistance.
(FAQ)
- Q: Can I install the grab bar without locating wall studs?
- A : It is strongly recommended to install both ends of the grab bar into wood wall studs to ensure proper support. Failure to do so may result in inadequate support.
- Q: What should I do if I encounter electrical wiring while drilling?
- A: Stop drilling immediately and consult a professional to safely navigate around the wiring. Avoid drilling into areas where electrical wiring may be present.
ITEMS REQUIRED
TOOLS REQUIRED
SAFETY WARNINGS
- DO NOT install this equipment without first reading and understanding this instruction sheet. If you are unable to understand these Warnings and Instructions, contact a healthcare professional, dealer or technical personnel for assistance before attempting to install this equipment- otherwise, an injury may occur.
- After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely.
- Grab Bars add security for bath and commode areas if attached as instructed. The location, size and angle of bars should be determined by a qualified professional to provide optimum safety and function.
- Use EXTREME caution on the wet tub or floor surfaces.
- Users with limited physical capabilities should be supervised or assisted in bath and commode areas, even when using the Grab Bars.
- This Grab Bar can provide support and increased stability for an individual weighing up to 350 pounds. Grab Bars are NOT designed to support the total weight of an individual. Use the bar for assistance ONLY
- Be sure Grab Bars are correctly and securely installed. NEVER use Grab Bars if any looseness is noted.
BEFORE INSTALLING GRAB BAR:
- Remove the Grab Bar and parts from the package.
- Locate wood wall studs.
- Attach Mounting Flange onto the Grab Bar, tighten the M5 setscrew, and then place the Grab Bar over the wall stud at the desired position.
- Mark the hole pattern if installing over ceramic tiles, place masking tape on the mounting area before marking the hole location
WARNING
BOTH ends of the grab bar must be installed into WOOD wall studs
Installation instruction
GRAB BAR MAY NOT PROVIDE DESIGNED AMOUNT OF SUPPORT UNLESS THESE
INSTRUCTIONS ARE STRICTLY FOLLOWED
For proper installation, both ends of the Grab Bar MUST be positioned over a
wall stud. For solid support, at least two (2) of the three (3) screws at each
end of the Grab Bar MUST go through the wallboard or tile and be tightly
secured into the wall stud. Grab Bar may be installed vertically, horizontally
or at an angle, so long as at least two (2) of the three (3) mounting screws
on both ends of the Grab Bar are secured into a wall stud (see Figure 2).
Locate the wall studs behind the wall before beginning installation (a stud
finder can be obtained from a hardware store).
THE FOLLOWING STEPS REQUIRE DRILLING INTO THE WALL
When drilling into the wall, exercise care to avoid any electrical wiring or
plumbing that may be located behind the wall. Damaged electrical wiring can
cause electrical shock and/or fire. Since older homes do not always fall in
line with current housing codes and requirements, know where internal wall
wiring is located so that no wires will interface with your installation.
PROPER INSTALLATION IS EXTREMELY IMPORTANT. IF IN DOUBT, INSTALLATION SHOULD
BE DONE BY A QUALIFIED PROFESSIONAL
TO INSTALL INTO WOOD WALL STUDS:
- Put on safety glasses before starting.
- Use the power drill and 7/64 inch drill bit to drill all holes into the wall and wood wall studs at the marked positions. NOTE: If installing Grab Bar over ceramic tiles, the 1/4 inch carbide tip drill bit will be needed for drilling through the tile, to prevent damage to the tiles. Drill pilot holes through the tiles by using a 1/4-inch carbide tip drill bit. Once a hole has been drilled through the ceramic tiles, use the 7/64-inch drill bit to drill a pilot hole in the wood wall stud itself.
- Place the Grab Bar on a wall, aligning mounting holes with the holes in the wall.
- Apply a bead of silicone sealant designed for wet applications to the back face of both grab bar mounting flanges. This will help prevent water from bleeding through the mounting holes and potentially damaging the wallboard.
- Insert the wood screws provided into one end of the Grab Bar, and screw into wall and wall stud.(HAND TIGHTEN ONLY) (see Figure 3).
- Repeat Step 4 for the opposite end of the Grab Bar.
- Securely tighten all mounting Wood Screws with a screwdriver.
- Install the O-ring onto the grab bar Mounting Flange.
- Slide the Escutcheon around the bend and press into place over the Mounting Flange O-ring.Wetting O-ring aids installation (See Figure 3).
USING GRAB BAR:
- Read understand and follow the information in the SAFETY WARNINGS section of this instruction booklet. Brasstech Inc. shall have no liability for any damage or injury caused by improper installation or use of this Grab Bar.
- Grasp the Grab Bar when exiting or entering the bathtub or when sitting down or rising from the commode.
- Use EXTREME caution on the wet tub or floor surfaces.
- DO NOT put the entire weight on Grab Bar. Grab Bar is rated for persons weighing up to 350 pounds when properly installed.
- DO NOT stand, sit or step on Grab Bar. DO NOT use Grab Bar as a step or platform to reach above the tub. Use the bar for assistance ONLY.
CARE AND MAINTENANCE
- Use of mild soap and water or a non-abrasive cleaner is recommended for cleaning.
- Periodically inspect the Grab Bar for damage or looseness. DO NOT use if any damage or looseness exists. Contact your authorized dealer for assistance.
- SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>