dji WV-001 Ronin RavenEye Image Transmission System User Guide
- June 5, 2024
- DJi
Table of Contents
dji WV-001 Ronin RavenEye Image Transmission System
Introduction
The Ronin RavenEye Image Transmission System is used to transmit the image signal to the DJI RS/RS 2/RS C/RSC 2, mobile phone and monitor, and more device, it is easy to check the live view remotely.
-
Antenna
Transmit the wireless signal. -
Reserved LED
Reserved. -
Power /Communication Port (USB‐C)
For charging and communication. -
HDMIPort
For connecting the camera’s HDMI port. -
RSS Camera Control Port (USB‐C)
For connecting to the gimbal’s camera control port. -
Battery Level Indicators
Indicates the battery level. -
Status LED
Indicates the system status. -
Power Button
Press and hold to power on/off. Press four times to restore the default Wi‐Fi password to 12345678. -
Cold Shoe
For connecting to the gimbal or camera.
Installation
- Attach the Image Transmission System to the gimbal or camera.
- Connect the HDMI port to the camera’s HDMI port using the provided HDMI cable according to the camera type.
- Connect the communication port to the gimbal’s Image Transmission port using the provided USB‐C to USB‐C cable.
- Connect the camera control port to the gimbal’s RSS camera control port.
- Balance the camera after installation. Refer to the gimbal’s user manual for details.
Usage
Power on the gimbal, camera and the Image Transmission System. The Status LED indicates the current status.
- LED Status Description
- Solid Red Not connected
- Solid Blue HDMI connected, or Wi‐Fi connection with DJI Ronin app connected.
- Solid Green HDMI and Wi‐Ficonnected
When used with the DJI RS 2/DJI RSC 2, the touchscreen (DJI RS 2 only) and the mobile device are able to display the camera view.With the Image Transmission System, ActiveTrack can be used. You can also control the gimbal via mobile phone.
When used with the DJI RS/DJI RSC, ActiveTrack and camera control are unavailable, other operations are the same. When used with the camera without a gimbal, use the mobile phone to control the camera and display the camera view.
Specifications
- Operation Frequency 2412-2462MHz，5745-5825MHz
- Weight 126 g
- Dimensions 82mm x 63 mm x 24 mm
FCC/ISEDC Compliance Notice
This device complies with Part 15 of the FCC/ISEDC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC/ISEDC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This device has been tested and meets the FCC/ISEDC SAR limits. This
equipment should be installed and operated with minimum distance 5mm between
the radiator& human
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>