Sanhe G171 High-Speed Remote Control Vehicle User Manual

G171 High-Speed Remote Control Vehicle
User Manual

CAUTIONS

1. Disassemble small parts should be put away, don’t let the kid swallow it.
2. If the operation site has other radio wave interference. please choose another site to play.
3. When the remote control power is low stop the operation immediately
4. .Do not dispose of the removed packaging materials, to avoid environmental pollution.
5. Store your remote control model in a dry and cool place
6. . Do not store in a place where near tire and high emperature ; humidity.
7. When the battery is wetted by water, please wipe oil the water thoroughly.

PRODUCT CONFIGURATION

INSTALL REMOTE CONTROL BATTERY

1. Push the cover in the direction indicated by the arrow, to open the battery cover (Fig. 1)
2. As shown (Fig. 2), install 3’1.5V “AA” batteries with the correct polarity (battery sold separately)
3. Close the battery cover, and push upward (Fig. 3).

ATTENTION

1. When installing the battery, you must place the battery positive and negative terminals with the battery box corresponding indicated terminals.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries

CHARGE AND INSTALL A RECHARGEABLE BATTERY PACK

1. First connect the plug of the rechargeable lithium battery pack with the charger port (as shown in Figure 4) (the charger indicator light turns green); then plug the charger into the power socket, (as shown in Figure 5). At this time, the charger indicator light is red). indicating that charging is in progress: when the charger indicator light turns green again, the charging time takes about two hours). the charging is finished.
   

2. Remove the clamping-lock on the battery cover of the racer base, and open the battery cover. (Fig. 6)

3. If (Figure 7), connect the right socket of the battery pack to the port of the battery compartment on the remote control car, and then insert the rechargeable battery pack into the battery compartment.

4. Cover the battery cover, and fasten the clamping-lock on the battery cover at the racer base (Fig. 8)

CHARGER/BATTERY PACK I CIRCUIT BOARD NOTES AND INSTRUCTIONS

1. In order to prevent over-voltage charging of the iron-lithium battery pack, the battery may be overheated or damaged orexploded, the charger adopts a voltage-limiting protection device, to avoid the above situation In order to better protect the battery performance. rt is recommended not to make the battery pack continue charging for over 24 hours, to ensure safety
2. This battery uses a low voltage, over discharge protection device When the battery is over-discharged, re-charging can be activated to ensure the durability or damage of the battery. In order to better protect the battery performance. it is recommended nonuse the racer. please turn the racer power switch to the -OFF- position. and remove the battery.
3. This circuit board adopts the overheat protection function: when the circuit board overheat protection function is activated. the racer (forwardireverse) function will stop for about 3-6 seconds. and then resume the function

REMOTE CONTROL PARTS DESCRIPTION AND STEERING FINE-TUNING

1. Remote control power switch: (Figure 9)

2. Remote control parts functions description: (Figure 10)
   

Steering fine-tuning: Let the racer resume straight forward, when it is unable to travel straight.

When the racer turns to the left, please turn the steering tine-tuning clockwise (Figure 11)

When the racer turns to the right, turn the steering tine-tuning counterclockwise (Figure 12)

CONTROL RACER

1. Install the steering wheel onto the remote control.

2. Set the frequency of the remote control and the vehicle
   A When setting up for the first time, the power switches of racer and remote control must be turned on at the same time within 3 seconds. When the frequency is correcting. the racer and remote control power indicator lights will flash When the frequency corroding Is completed. the power indicator light is on all the time.) (Figure 13)
   B. It the time is not enough to match the frequency. first turn off the racer and remote control power. and then re-correction
   Note: When the power of the remote control racer and the remote control is low. the power indicator light flashes. so the battery should be replaced or the rechargeable battery pack should be recharged

3. Put the linger around the remote control trigger and push backward. the racer will drive forward. use your finger to push forward the trigger. the car will drive backwards (Figure 14)

4. When using the trigger to control the racer, turn the steering wheel at the same time, to control the leftiright-turn of the racer.

ATTENTION

• Please pay attention to the polarity, when installing or replacing the battery;
• Non-rechargeable battery is not rechargeable
• The rechargeable battery pack should be taken out of the racer, before charging;
• When charging the battery, adult supervision is required;
• Do not use old or new batteries or different types of batteries;
• Remove the exhausted battery from the racer
• The power terminal cannot be short-circuited;
• When operating, the hand can not touch the remote control antenna, otherwise the antenna will affect the remote control distance, the break off antenna should be handled by an adult.
• This racer is equipped with strong power. When driving at high speed, you can’t brake suddenly due to inertia. Please pay special attention when using it.
• When the racer speed slows down, the racer battery is low. Please charge the racer battery according the above ways;
• Connect the charger plug and charging port in a correct way, when charging;
• Please take out the batteries at the remote control and the racer, when not in use for a long time.
• Unpacking is carried out under an adult guidance;
• Keep this information for future reference

|
---|---
|
|
|
|

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device  must accept any interference received, including interference that may cause undesired operation

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not  installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur  in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>