RayBit POD 7 Wireless Speakerphone Kit User Manual

May 15, 2024
RAYBIT

RayBit logo

Wireless Speakerphone Kit

RayBit POD 7 Wireless Speakerphone Kit

User Manual

What’s in the box

RayBit POD 7 Wireless Speakerphone Kit - Box

Overview

RayBit POD 7 Wireless Speakerphone Kit - Overview

Easy Set-Up

• About main sperkerphone

  1. Power On/Off
    Long press ON/OFF  for 3s, the speakerphone will be turn on/off with hint tone.

  2. Connect and disconnect
    2.1 Wireless connection
    A. After power on, long press wireless pairing button for about 2s to start pairing mode.
    You will hear “pairing” (white and blue flashing light).
    B. Turn on your device and choose to connect with the speakerphone. Wait for 3s until you hear hint tone.
    C. To cancel pairing: a short click on pairing button.(flashing light turn white).
    D. To disconnect: a long press on pairing button for about 2s, you will hear hint tone.
    (Blue light turn white). 2.2 Connect by USB cable
    Connect with computer by USB cable.RayBit POD 7 Wireless Speakerphone Kit -
Cable 12.3 Connect by Wireless Receiver
    Connect the USB wireless receiver to your computer, and start pairing mode on speakerphone. Wait for about 15 seconds until the pairing is completed, then the speakerphone is connected and ready to go.RayBit POD 7 Wireless
Speakerphone Kit - USB Wireless

  3. ChargingRayBit POD 7 Wireless Speakerphone Kit - Charging Main speakerphone: connect the speakerphone by USB to an AC adapter or USB charging port, it will start to charge.

  4. Answer /end calls
    Press button to answer calls, press button to end calls.

  5. Speaker volume up/down
    Speaker volume up, Speaker volume down

  6. Mute
    Press mute button among any of the main speakerphone and wireless microphones, all microphones will be muted at the same time. Press again to unmute.
    When microphone is working, light will be white. When muted, light will be red.

  7. Automatic shut off
    When device is not connected for lSmins, it will shut off automatically.

  8. Battery level
    When charging or short press power key, the green light is the charging/power level indicator. During charging it will be green flash light, and full green light when charging is completed.

About wireless microphone

  1. Power On/Off
    Long press mute button for 3s, it will be turned on/off.

  2. Connect and Disconnect
    A. Long press mute button on the extension mies for about 6s, the white light will flash quickly to enter pairing mode.Then long press on the call key and power key of main speaker for about 65+ to start pairing.
    (Note: Usually the wireless microphones should have been paired with main speakerphone already before delivery. n special cases, refer to this method to pair again if they were disconnected).
    B. When wireless mic is disconnected with main speakerphone, it will be white flash light and shut down automatically after 18mins.
    C. When main speakerphone is shut down, the connected wireless mies will be shut down at the same time.

  3. Charging
    Wireless microphone: While the main speakerphone is charging, put the wireless microphone magnetic charging connector near the speakerphone charging port.
    Wireless microphone will be connected and start to charge.
    (Note: When battery under low level, it will be red flash light. During charging it will be green flash ight, and full green light when charging s completed.)

RayBit POD 7 Wireless Speakerphone Kit - Charging 2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals