VEVOR WS-USR-D Smart Dimmer Switch Instruction Manual
- May 15, 2024
- VEVOR
Table of Contents
Technical Support and
E-Warranty Certificate
www.vevor.com/support
SMART DIMMER SWITCH
MODEL:WS-USR-D
WS-USR-D Smart Dimmer Switch
We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only
represents an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and does not necessarily mean to
cover all categories of tools offered by us. You are kindly reminded to verify
carefully when you are placing an order with us if you are actually saving
half in comparison with the top major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us:
Technical Support and E-Warranty Certificate
www.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
| Warning-To reduce the risk of injury, user must read instructions manual
carefully.
---|---
| This product is subject to the provision of European Directive 2012/19/EC.
The symbol showing a wheelie bin crossed through indicates that the product
requires separate refuse collection in the European Union. This applies to the
product and all accessories marked with this symbol. Products marked as such
may not be discarded with normal domestic waste, but must be taken to a
collection point for recycling electrical and
electronic devices
FCC compliance information statement：
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement This equipment complies with FCC RF
radiation exposure limits set forth for an uncontrolled environment. This
device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter. “To comply with FCC RF exposure compliance
requirements, this grant is applicable to only Mobile Configurations. The
antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.” We, Sanven
Corporation, has determined that the equipment shown as above has been shown
to comply with the applicable technical standards, FCC part 15. There is no
unauthorized change is made in the equipment and the equipment is properly
maintained and operated.
PRODUCT DESCRIPTION
Thank you very much for choosing this product. Please read all instructions
before use. This information will help you achieve the best results.
This new designed glass panel wireless touch smart switch is designed with
WiFi+RF to replace traditional switches with a variety of ways to control.Now
one new smart feature as new easier pairing method with Bluetooth supported is
added into the Smart Life/Tuya App,together with the backlight on/off and relay
status.And its scratch resistance glass panel is suitable for different
decoration styles with its best value. Note: Button sound on and off: no button
operations before operations begin within 6 seconds.Then press switch button
for 4 times and long press for the fourth time(20s) until the switch beep
sounds as Di-Di for 2 times for successful operation.
SAFETY INFORMATION
Risk of Electric Shock:Electricity can cause personal injury and property
damage if handled improperly.If you are not sure about any part of these
instructions,please seek professional assistance from a qualified electrician
Technical Parameters:
Model:WS-USR-D Working
voltage: 100-250V AC, 50Hz/60Hz
Max. total current: 2A
Max. Load Power: 220W(110V)
Wireless type: WIFI2.4G+RF433MHz
Working temperature: 0℃~40℃
Support system: Android/iOS
Warnings : Turn off the power at the circuit breaker and test that power
is off before wiring.
INSTALLATION
Note:
- Make sure that the power at the circuit breaker is off before wiring.
- Neutral Wire is required.Confirm the wall box contains a Neutral Wire(typically white).If the wall box don’t have a Neutral Wire,please try another location at your home or call a professional electrician to install the switch.
- The wire colors indicated in this manual are the usual colors and may differ in some houses.
- Ensure the wire conductors are securely fastened to each wire.
- Ensure the Wi-Fi signal is steady and normally working before wiring.
- If you don’t have any wiring experience,please call a professional electrician.
Step 1:
- Turn off the circuit breaker and use the electrical tester to test the power.
- Ensure the circuit breaker is off before wiring.
Attention : Please disconnect the power supply before installing or removing the device for avoiding irreversible damage on the device from the electric current or some unpredictable problems such as lamp flashing.
Step 2：
Remove the old switch.
Step 3:
Remove the switch and pull it away from the wall. Identify Line/Load
Wire(Note:The color of your wire may be different from the color shown on the
manual.)
Verify power is off
- We recommend you remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit.
- You may need to turn off more than one circuit breaker.
Step 4:
- Take pictures of the wiring.
- Follow the wiring diagram to connect the switch wires to the wires in the wall box with the wire conductors.
Step 5:
- Remove the panel with screwdriver.
- Please don’t install with electricity power on.
Step 6:
- Prepare to install wiring.
A. Live wire connects “ L ” terminal.
B. Neutral wire connects “ N ” terminal.
1 Gang connects “L1” terminal
1 Gang L1 and N line.
Step 7:
- Put the switch into switch box in the wall.
- Mount the two side screws.
- install the glass panel (install from up above).
- Finish installation.
ADD DEVICES
- Download Smart Life App.
|
---|---
http://app.yimusmart.com/smartlife|
http://app.yimusmart.com/smartlife
Please scan the QR code or download Smart Life on App store.
-
Registration or Log in.
• Download “Smart Life”Application.
• Enter the Register/Login interface;tap “Register” to create an account by entering your phone number to get verification code and “Set password”.Choose “Log in” if you already have a Smart Life account. -
Configure the APP to the switch.
• Preparation: Ensure the switch has been connected with electricity;ensure your phone has been connected to Wi-Fi and is able to connect to the Internet.
Note :
• The switch only supports 2.4G network.If you have connected 5G network,please disconnect 5G network firstly and connect 2.4G network.
• Wi-Fi link method: (two matching methods).
3.1. Method one:
Please
connect the device according to the configuration process.
3.2. Method two:
- Make sure your phone is connected to Wi-Fi and Bluetooth.
- Reset: Press the switch button for 6 times,and hold on the 6th time,then release until you hear Di-Di-Di(3times),and the blue indicator on the switch will flash fast after 3 seconds.Reset/re-pair is successful.
- Open the Smart Life App, click “+” in the upper right corner, find the device to be added in the device discovery location, and click “Add”.
- Enter the Wi-Fi password, click “Next”, and wait for the connection to complete.Add the device successfully,you can edit the name of the device to enter the device page by click “Next”
- Click“Done”to enter the device page to enjoy your smart life with home automation
3.3.How to reset/re-pair Wi-Fi code:
Press the switch button for 6 times,and hold on the 6th time,then release
until you hear Di-Di-Di(3 times),and the blue indicator on the switch will
flash fast after 3 seconds.Reset/re-pair is successful.
Enter Smart Life Skill in Alexa APP
-
Complete product networking configuration in the App Complete the device’s networking configuration according to the prompts in the App.
Note : In the App, change the name of the device to an easily identifiable name such as Alexa; names are usually in English, such as “bed light”. -
How to connect Smart Device to Amazon Alexa.
• Launch Smart Life App, sign into your account and make sure Smart
Device is on the device list.
• Minimize Smart Life App, then launch the Alexa App and sign in your Alexa account and make sure you have at least one Alexa smart speaker-controlled device installed like Echo dot, etc.
• In the upper left corner of Home page, press the button to show APP Menu. Then select in the menu.
• Type in “ Smart Life ” in the search and press the
search button next to it. • Enable Smart Life Smart Skill then sign in your
Smart Life account to complete your account set up.
• Once your account has
been successfully linked, ask Alexa to discover devices. After a 20-second
searching, Alexa will show all the available devices. • In the Smart Home
page, you can group your devices in different categories. Your SMART LIFE APP
has now been paired with Alexa. Now you can control your Smart Device through
Alexa.
HOW TO CONNECT SMART DEVICE TO GOOGLE HOME
-
Launch the Google Home App and make sure Google Home speaker is installed. If not, please follow Google Home speaker installation instruction to complete the installation.
-
Once Google Home is installed, in the upper left corner of App Home page, Pressing button to show App menu.
Then press“Home Control”in the menu.
-
After successfully linking your account, in the Google Home App you can see all your smart devices from your SMART LIFE App account. You can assign rooms for each device.
-
Now you can use Google Home to control your smart device, you can say like.
LIST OF ACCESSORIES
- Products 1(Single package1;Two packages*2)
- Instruction manual*1
- Screw(M4-35mm )2(Single package2;Two packages*4)
SERVICE
Thank you for your trust and support to our products, we will provide you with
a two-year worry-free after-sales service (freight is not included), please do
not alter this warranty service card, to safeguard your legitimate rights and
interests. If you need service or have any questions, please consult the
distributor or contact us.
Product quality problems occur within 24 months from the date of receipt,
please prepare the product and the packaging, applying for after-sales
maintenance in the site or store where you purchase; If the product is damaged
due to personal reasons, a certain amount of maintenance fee shall be charged
for repair.
We have the right to refuse to provide warranty service if:
- Products with damaged appearance, missing LOGO or beyond the service term.
- Products that are disassembled, injured, privately repaired, modified or have missing parts.
- The circuit is burned or the data cable or power interface is damaged.
- Products damaged by foreign matter intrusion (including but not limited to various forms of fluid, sand, dust, soot, etc.)
RECYCLING INFORMATION
All products marked with the symbol for separate collection of waste
electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be
disposed of separately from unsorted municipal waste. To protect your health
and the environment, this equipment must be disposed of at designated
collection points for electrical and electronic equipment designated by the
government or local authorities.
Correct disposal and recycling will help prevent potential negative
consequences for the environment and human health. To find out where these
collection points are and how they work, contact the installer or your local
authority.
Made In China
Technical Support and
E-Warranty Certificate
www.vevor.com/support
Documents / Resources
|
VEVOR WS-USR-D Smart Dimmer
Switch
[pdf] Instruction Manual
WS-USR-D Smart Dimmer Switch, WS-USR-D, Smart Dimmer Switch, Dimmer Switch
---|---