Icecat HSR3918FI Refrigerator User Guide
- May 15, 2024
- Icecat
Table of Contents
Icecat HSR3918FI Refrigerator
Product Information
Specifications
- Model: HSR3918FI HSOIF9183
- Available Variants: MP, MX, PG, PH, PB, PW, BP, GP, MB
- Languages: EN, SK, RO, SR, DA, FI, NO, SV, AR, SL, HR, ET, LT, LV, DE
Product Usage Instructions
Safety Information:
Ensure to follow all safety precautions mentioned in the user manual before using the refrigerator.
Power Interruption:
In case of a power cut, follow these tips to ensure food safety and quality:
- Open the door/drawer as few times as possible.
- Avoid putting additional food into the appliance during a power interruption.
- If a prolonged power cut is expected, make ice in advance and store it in the fridge compartment.
- Inspect the goods immediately after power is restored.
- Consume or cook and refreeze defrosted food to prevent health risks.
Water Connection:
Follow these steps for connecting the water filter:
- Cut the pipe into two pieces with the required length.
- Insert pipe into the mounting fixture of the water filter.
- Secure the pipe with a locking clip.
- Connect the pipe to the adapters that suit the water main.
FAQs
- Q: What should I do if the ice cubes smell and taste unpleasantly?
- A: Ensure no unpacked food is stored in the freezer compartment and discard any affected ice cubes.
- Q: How can I address an error code on the control panel?
- A: If an error code appears, it indicates an electric operating problem. Contact Customer Service for assistance.
- Q: How should I handle high water pressure during installation?
- A: Install a pressure reducer if the water pressure exceeds 0.6 MPa to prevent damage to the appliance.
“`
Safety information
EN
EN WARNING: Risk of fire/flammable material. The symbol indicates there is a risk of fire since flammable materials are used. Take care to avoid causing a fire by ingiting flammable material.
EN
Problem
Possible Cause
Possible Solution
The ice cubes smell and taste unpleasantly.
You hear sounds like flowing wa ter or ice cubes dropping
· Ice Maker function is not used of- · Ice can take the smell and odour
ten.
of other substances. Discard the
Unpacked food is stored in the ice cubes.
freezer compartment.
This is normal when ice or water function is activated
Water leaks out · Water pressure is too high. ofthe appliance · Water hose is damaged.
· Interrupt the power supply, close the water tab and call the Cus tomer Service
The control pan el shows an error code.
An electric operating problem has occured.
Call the Customer Service.
9.2 Power interruption
In the event of a power cut. food should remain safely cold for about 5 hours.
Follow these tips during a prolonged power interruption, especially in summer:
Open the door/drawer as few times as possible.
Do not put additional food into the appliance during a power interruption.
If prior notice of a power interruption is given and the interruption duration
is longer than 5 hours, make some ice and put it in a container in the top of
the fridge com partment.
An inspection of the goods is required immediately after the interruption.
As temperature in the fridge will rise during a power interruption or other
failure, the storage period and edible quality of food will be reduced. Any
food that defrosts should be either consumed, or cooked and refrozen (where
suitable) soon after wards in order to prevent health risks.
[ i ) Notice: Memory function during power interruption
After restoration of power the appliance continues with the settings that were
set be fore the power failure.
33
EN
ffi WARNING!
Only connect to drinking water supply. The water filter only filters
impurities in the water and makes ice clean and hygienic. It cannot sterilize
or destroy germs or other harmful substances.
Too high water pressure in the hose can damage the appliance. Install a
pressure reducer when the water pressure in the hose exceeds 0.6 MPa.
Before connection. check whether the water is clean and clear.
Water connection
Pressure of the cold water has to be 0.15-0. 6 MPa.
The maximum permitted length of water hose is 8 meter. Longer hoses will
affect the ice cubes and cold water content.
Ambient temperature has to be O °C minimum.
Keep the water hose away from heat sources.
1.Cut the pipe into two pieces with the required length to connect the filter (A) with the appliance (Bl) and the water tap (B2) (Fig. 10.5-1). Make sure to get a square cut by using a sharp knife.
10.5-1
2. Insert pipe (Bl) approx. 12 mm deep into the mounting fixture of the water filter (A) (Fig. 10.5-2). Take care to install the filter in the correct direction. T he dart shows the direction of water flow.
10.5-2
3. Secure the pipe with a locking clip (C) according to Fig. 10.5-3.
4. Repeat step 2 and 3 with the pipe (B2) on the other side of the filter
5.Connect the end of pipe (B2) to one ofthe adapters “D” or “E and F” which suits to the water main (Fig. 10.5-4).
6. Remove the plug in the valve at the back of appliance
(Fig.10.5-5). 7.Connect the end ofB1 to the valve at the back of
the appliance (Fig. 10.5-6).
8. Open the water tab to check if the system is leak
r free andflush the pipe. WARNING!
Ensure that the connections are always firm, dry and leak free.
10.56
t., I
Make sure the hose is never crushed, kinked, or twis
ted. 35
EN
10.6 Aligning the appliance
10.7
.l .l
t f
r
r,· 10.7-1-10.7-2 t
ffi WARNING!
The appliance should be placed on a flat and solid sur face.
1. Tilt the appliance slightly backwards (Fig. 10.6). 2. Set the feet to the
desired level.
Make sure the distance to the wall on the hinge sides is at least 10 cm.
3. The stability can be checked by alternately bump ing on the diagonals. The
slightly swaying should be the same in both directions. Otherwise the frame
can warp; possible leaking door seals are the result. A low tendency to the
rear facilitates the closing of the doors.
10.7 Fine tuning ofthe doors
If the doors are still not in one level after levelling the doors by the feet.
this mismatch can be remedied by turning the hinge lifting shaft at the right
bottom cor ner of refrigerating door with a spanner (Fig. 10.7)
Clockwise turn lifting shaft with spanner to lower door height (Fig. 10.7-1).
Antic lock wise turn lifting shaft with spanner to lift door height (Fig.
10.7-2).
Do not adjust the hinge lifting shaft excessively to a height which might cause the shaft
to leave its original locked position. (Adjustable height range: 3 mm)
10.s
,-;======.:::-,
10.8 Waiting time
To the maintenance-free lubrication oil is located in the
capsule of the compressor. This oil can get through
the closed pipe system during slanting transport. Be
fore connecting the appliance to the power supply you
2h
have to wait at least 2 hours (Fig.10.8) so that the oil runs back into the capsule.
36
10.9 Electrical connection Before each connection, check that: The plug and
fuse of the power supply are appropriate according to the rating plate. The
outlet is grounded and there are no power strips or extension cords. The plug
and socket are strictly in accordance with the standards.
Connect the plug to a properly installed domestic outlet.
&WARNING:
To avoid risks, customer service must replace any damaged power cord (see
warranty card).
10.10Door removal and installation Should you need to remove the doors from
the appliance, follow the door removal and installation instructions below.
(Fig. 10.10).
&WARNING:
Before performing this operation, turn off the appliance and unplug the outlet
plug.
Block the water supply. The device is heavy. Always handle the appliance with
at least two people. Do not tilt the device more than 45° or place it
horizontally on the floor. The door may fall down and injure people, or be
damaged during these steps, proceed
1. Release the left side of two couplers from water in the front left corner
at the bottom of the appliance: press and hold the clamp as shown and remove
the water pipe (Fig. 10.10-1).
2. Loosen the screw on the hinge cover and remove the cover (Fig. 10.10-2). When removing the freezer door, disconnect all cables except the ground cable.
‘ ‘10.10-2
3. Loosen the screws that hold the top hinge in position, then remove the
hinge. (Fig. 10.10- 3).
4. Lift the door to remove it (Fig. 10.10-4). When removing the freezer door,
lift it high enough to remove the water connection at the bottom of the
appliance.
5. Replace door by reversing removal steps. Make sure the ground wire is
fixed by the screw.
6. Reinstall the water connection.
(I] Nota: fridge door
The images show the removal of the freezer door. For the refrigerator door,
use the matching parts from the other side.
38 224
11.1 Product sheet according to the regulation (UE) N!! 2019/2016
Commercial brand model identifier
Haier
HSR3918Fl’/HSO’IF9183/HSR3918El’/HSO’IE9183/ HSR5918DI/HS05918DI/HSO*ID9185
model category energy efficiency class Annual energy consumption (kWh/year)1l
Fridge volume (L) Freezing volume (L) Number of stars
Temperature of other compartments > 14 ·c Sistema no frost Temperature rise
time (h) Freezing capacity (kg/24 h) climatic class This appliance is intended
to be used at an ambient temperature between 10 ·c and 38 ·c. Noise emission
class and airborne acoustic noise emissions (db (A) re lpW) Type
Frigorffico-congelador F/F/E/E/D/D/D
393/393/317/3 l 7/253/253/253 337 /337 /337 /337 /333/333/333
178 113
no Si 5 10 SN-N-ST
((40)
Frestanding
l)based on the results of the standard test for 24 hours. Actual power consumption will depend on how the appliance is used and where it is located. 11.2 Additional technical data
Total storage volume
515/515/515/515/511/511/511
Voltage / Frequency
220-24ov~/50 Hz
Defrost input power (W)
200
Main fuse (A) Refrigerant
15 R600a
Water pressure in MPa
0,15-0,6
Dimensions (H/W/D in mmJ
1775/908/659
11.3 Standards and directivesC E:
This product meets the requirements of all applicable EC directives with the
corresponding harmonized standards, which provide for CE marking.
39
We recommend going to our Haier customer service and the use of original spare
parts.
If you have a problem with your device, first check the TROUBLESHOOTING
section.
If you cannot find a solution there, please contact your local dealer or the
Service and Support area at www.haier.com, where you can find phone
numbers and frequently asked questions and where you can activate the service
claim. To contact our Service, make sure you have the following information
available. Information can be found on the nameplate.
Model
N.Q SERIAL
Also check the warranty card supplied with the product in case of warranty.
For general business inquiries, please see our addresses in Europe below:
Country* address
Haier European Addresses Country*
address
Italy Spain Portugal
Haier Europe Trading SRL Via De Cristoforis, 12 21100 Verese ITALIA
Haier Iberia SL Pg. Garcia Faria, 49-51 08019 Barcelona ESPANA
Francia Belgium-FR Belgium-NL Netherlands Luxembourg
Haier France SAS 3-5 rue des Graviers 92200 Neuilly sur Seine FRANCIA
Haier Benelux SA Anderlecht Route de Lennik 451 BELGICA
Germany/ Austria
Haier Deutschland GmbH Hewlett-Packard-Str. 4 D-61352 Bad Homburg ALEMANIA
Haier Appliances UK Co.Ltd. One Crown Square
Un ited Kin gdom Church Street East
Woking, Surrey, GU21 6HR RU
Polonia check Hungary Greece Romania Russia
Haier Poland Sp. zo.o. Al. Jerozolimskie 181B 02-222 Warszawa POLONIA
*For more information, see www.haier.com
40
Duration of the guarantee of the refrigeration appliance: The minimum warranty is: 2 years for EU countries, 3 years for Turkey, 1 year for UK, 1 year for Russia, 3 years for Sweden, 2 years for Serbia, 5 years for Norway, 1 year for Morocco, 6 months for Algeria, in Tunisia no legal guarantee is required. The period of spare parts for the repair of the appliance: Thermostats, temperature sensors, printed circuit boards and light sources are available for a minimum period of seven years after the last unit of the model is sold. Handles, door hinges, trays and baskets for a minimum period of seven years and door seals for a minimum period of 10 years, after the marketing of the last unit of the model. Technical assistance To contact technical support, please visit our website: https://corporate.haier-europe.com/ en/ In the “website” section, choose your product brand and your country. You will be redirected to the specific website where you can find the phone number and the form to contact technical support *For more information on the product, see: https://eprel.ec.europa.eu/
References
- Haier Europe
- Choose your country or region - Haier
- Choose your country or region - Haier
- Haier Europe