BOOST AUDIO SYSTEMS B62ABT ATV UTV Marine Weatherproof Waketower System User Manual

BOOST AUDIO SYSTEMS B62ABT ATV UTV Marine Weatherproof Waketower System

THIS PACKAGE CONTAINS

1. B62ABT Marine Waketower Speaker System (1 Active+ 1 Passive)
2. Bluetooth Multi-Function Controller
3. Handlebar Mounting Kit for Bluetooth Controller
4. Mounting Bracket Kit
5. Power Wire Harness Kit
6. Security Rope
7. User Manual Quick Start Guide
8. Warranty Card

INFORMATION TO THE USER

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by BOSS Audio Systems is under license. Other trademarks and trade names are those of their respective owners.

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of this device.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by user. This equipment complies with FCC/ IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure (MPE) evaluation. But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de­signed to provide reasonable protection against harmful interference in a residen­tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar­antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate or reorient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION!!
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

IMPORTANT SAFETY PRECAUTIONS

• Do not operate mobile equipment while driving a motorized vehicle – safe driving and the safety considerations of others should always be your highest priority.
• In the event, you should notice smoke, strange noises, or odor from this product, or any other abnormal signs, immediately turn off the power and consult your dealer or the nearest authorized BOSS AUDIO Service Center. Using this product in this condition may result in permanent damage to the system.
• Set your volume control at a low setting, then slowly increase the sound until you can hear it comfortably without distortion, or ear discomfort.
• BE SURE TO OBSERVE THE FOLLOWING GUIDELINES
• Do not turn up the volume so high that you can’t hear what’s around you.
• Use caution or temporarily discontinue use in potentially hazardous situations.

INSTALLATION PRECAUTIONS

WARNING – Always consult a professional installer

• Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without professional training and experience in electronic equipment and motorized vehicle accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards

• Refer any repairs to a qualified BOSS AUDIO SYSTEMS Service Center

• The B62ABT can be powered from a vehicles cigarette lighter/ auxiliary power port, or hard-wired directly to the battery through an optional relay/ accessory switch

• When wiring directly to the vehicle’s battery, be sure to disconnect the battery negative terminal wire before starting any wiring procedures, it is suggested that an
  optional fuse and fuse holder (not included) with a minimum rating of 20 Amps be in line with the positive battery terminal

• The ground cable length should not exceed 18 inches (See wiring diagram)

• The B62ABT has a weather-resistant design, it should not be submerged in or
  underwater under any circumstances

• Use only the installation parts provided with the B62ABT

CAUTION!! Using other mounting methods may void this warranty

GETTING STARTED

GETTING TO KNOW YOUR B62ABT MUL Tl FUNCTION CONTROLLER (MFC)

1. MFC • MULTIFUNCTION CONTROLLER
2. BLUETOOTH INDICATOR LED(BLUE) / AUX-IN STATUS INDICATOR(RED)
3. 3.5mm AUX-INPUT
4. PLAY/PAUSE / Press and hold for POWER ON or OFF
5. PREVIOUS TRACK/ Press and hold for VOL –
6. NEXT TRACK/ Press and hold for VOL + /
7. Warning tone while up to maximum volume in Bluetooth mode
8. Disconnect the currently connected Bluetooth device by pressing the 0 buttons for 4 seconds
9. Clear any paired Bluetooth device in memory by pressing the O button
10. for 8 seconds
11. Disconnect the currently connected Bluetooth device by turning off Bluetooth in your device setting menu
12. When powered on and no Bluetooth device is paired or connected,
13. the blue-lit I button flashes quickly for 10 minutes until powered off.
14. If the Bluetooth device is out of connection range, the Bluetooth pairing/ connection will be automatically disconnected and the blue-lit O button will flash quickly for 10 minutes until powered off.
15. When the operating voltage is lower than 9.5Volt, MFC gives a warning tone
16. MFC concludes tonnes of definitions: Power On/Off, Bluetooth connection
17. Disconnection, Maximum volume, Lower voltage

BLUETOOTH OPERATION

PAIRING & DISCOVER/NG A NEW BLUETOOTH CONNECTION

1. Power on the B62ABT by pressing and holding down the Play/Pause multifunction button for 3 seconds. The C) blue LEDs will start to flash, signalling that the B62ABT is now ready for Bluetooth pairing.
   NOTE: You have 30 Seconds before you must restart this procedure again.

2. Now that the B62ABT is in pairing mode:

ANDROID users:

• a. Go into the Settings Menu of your device
• b. Enter the Bluetooth Menu
• c. TURN ON Bluetooth and press SCAN
• d. “BOSS AUDIO B62ABT” will now be displayed under AVAILABLE DEVICES
• e. Press “BOSS AUDIO B62ABT” to get Bluetooth connected

iOS users:

• a. Go into the Settings Menu of your iOS device
• b. Enter the Bluetooth Menu
• c. TURN ON Bluetooth
• d. “BOSS AUDIO B62ABT” will now be displayed
• e. Press “BOSS AUDIO B62ABT” to get Bluetooth connected

1. If the BOSS AUDIO B40RGB is not seen, repeat the above steps to refresh the
   “Device List”

2. When the connection is successful, the C) blue LED will turn to solid blue from flashing. You are now ready to stream music from your favorite media player to the B62ABT.

RECONNECTION

1. Power on the B62ABT and your last paired device Bluetooth.

2. The unit will now automatically reconnect. The I blue LED will turn to solid blue.

3. If your device was previously paired with the B62ABT, but it wasn’t the last paired device:
   a. Ensure no other devices are currently paired
   b. Enter the Bluetooth Menu on your device being paired
   c. “ BOSS AUDIO B62ABT” will display under AVAILABLE DEVICES
   d. Choose the “BOSS AUDIO B62ABT” to reconnect

4. If the device is out of range from the B62ABT, it will disconnect automatically and the O blue LED will flash. If the device is back in range within 10 minutes, the B62ABTwill reconnect to the device. Otherwise, the O blue LED will keep flashing for 10 minutes until powered off.

• To avoid battery exhaustion, be sure to occasionally run the
• Tips: Vehicle engine while using this product.
• UsinQ this product without running the engine can drain the battery.

STREAMING MUSIC

MULTIFUNCTION cONTROLLER BLUETOOTH OPERATION

1. Press the PLAY/PAUSE once to start playing music or press the PLAY button from your device touch screen
2. To skip songs or advance, press the NEXT TRACK button
3. To select the previous song, press the PREVIOUS TRACK button

VOLUME CONTROL

1. To raise the volume, Press and Hold the VOL+ button for 2 – 3 seconds
2. To lower the volume, Press and Hold the VOL – button for 2 – 3 seconds

TIPS: Make sure your device Bluetooth volume is set at 75% level before stowing it into the carry pouch

AUX-INPUT

B62ABT can play audio from any device that has a 3.5mm headphone audio jack.

MULTIFUNCTION CONTROLLER AUX-IN OPERATION

1. Power on the B62ABT by pressing and holding down the multifunction button for 3 seconds PLAY/PAUSE
2. Disconnect any paired Bluetooth device by turning off Bluetooth in the Settings of your device Menu
   Using the supplied 3.5mm audio cable, connect the 3.5mm AUX jack of the multifunction controller to the headphone jack on your device. The LED turns red to indicate it is in AUX mode.

VOLUME CONTROL

1. To raise the volume, Press and Hold the VOL + button for 2 – 3 seconds
2. To lower the volume, Press and Hold the VOL – button for 2 – 3 seconds

The buttons on the multifunction controller cannot be used to select songs.

Tips: Make sure your device headphone volume is set at 75% level

BEFORE INSTALLING THIS PRODUCT

To avoid potential shorts in the electrical system, be sure to disconnect the(-) bat­tery cable before installation. Use this unit with a 12-Volt battery and negative ground­ing only. Failure to do so may result in a fire or malfunction.

CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, D0 DOES NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

When replacing the fuse, be sure to only use a fuse of the rating specified on this product. To avoid short-circuiting, cover any disconnected leads with insulating tape. It is especially important to insulate any unused wires, which if left uncovered may cause a short circuit. When connecting other devices to this product, refer to the manual for the product to be connected. The black cable is ground, make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the vehicle’s body frame or direct to the battery if your vehicle does not have a grounded chassis frame. The ground wire of this unit’s power amp and a second powered system must be connected to the frame separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire or malfunction.

SPEAKER MOUNTING SUGGESTIONS

TOOLS NEEDED

• 12mm Socket, Wrench, or Pliers
• 6mm Allen Wrench

INSTALLATION INSTRUCTIONS

Hand Tools Required:

■  3/16″ Hex Key and Bit Socket

■  5/32″ Hex Key and Bit Socket

■  Torque Wrench (in/lbs or nM)

■  Thread Lock Compound

| STEP 1: Removing the top half of the clamp

Using the 3/16″ Hex key, remove the top clamp bolts, and note

the Caution labels for correct torque settings later.

---|---
STEP 2: To adjust the speaker position

If the speaker position is not to be changed, remove the screws and apply thread locker compound. Using the 5/32″ hex bit socket, torque swivel screws to 44 in/lbs (SnM).

To change the speaker position, use the 5/32″ hex key remove the screws

Note:   the orientation  of  the  screws must remain  in  the  12 and 6

o’clock positions after moving the bottom clamp to the desired position.

| STEP 3: Swivel screws

Apply thread locker compound to the screws. Tighten the screws using the 5132″ Hex bit socket and torque wrench to 44 in/lbs (5nM).

STEP 4 : Securing clamp bolts

Using the correct rubber pads (labeled for 0.0.) install on both top and bottom half of clamps. Apply thread locker compound to the bolts.Hand tighten the bolts evenly {both sides should have the same spacing between bolls).Using the 3/16″ Hex bit socket, set the torque wrench to 65 in/lbs (7nM).

| STEP 5: Security rope

loop therope around the base of the clamp and bar, secure with the supplied hardware

WIRE DIAGRAM

SPECIFICATIONS

BLUETOOTH

• Version: 5.0 w/ EDR
• A2DP, AVRCP
• Range: 33ft/ 10m (line of sight)

SPEAKERS

• Impedance: 40
• Magnet: Ferrite
• Cone Type: Injected Polypropylene Cone with Butyl Rubber Surround
• Tweeter Size: 1″ PEI DOME

AMPLIFIER

• Input impedance: 1 Oko
• Frequency Response: 45Hz-20kHz
• Low Battery Shut Off
• Standby Current 0.5mA

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

GENERAL

• Swivel Metal Clamp System: 1-1/2″ -3″
• Operational Power: 12VDC (10-16V allowable)
• MAX Current Draw: 7.8 A
• Replacement Fuse: 1 OA AGC TYPE
• Color: Black
• Weight: 13.91Ibs / 6.31Kg
• Dimensions cm WxHxD: 21.7 x 28.4 x 23.8
• Dimensions Inches WxHxO: 8.54 x 11.18 x 9.37
• BOSS Audio Systems
• 3451 Lunar Court Oxnard, CA 93030
• www.bossaudio.com
• 805-751-4853 Customer Service
• Tech Support: www.bossaudio.com/support

The Bluetooth” word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by BOSS Audio Systems is under license.
Other trademarks and trade names are those of their respective owners.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>