HAGERMAN TUBEKLON Mythical Beast Overdrive Tube Pedal Kit Owner’s Manual
- May 15, 2024
- HAGERMAN
Table of Contents
HAGERMAN TUBEKLON Mythical Beast Overdrive Tube Pedal Kit
Product Information
Specifications
- Item: Mythical Beast Overdrive Tube Pedal Kit
- Made in: USA
- Bypass Controls: True Bypass
- Size: 1590BB
- Input Power: -9V @130mA
Product Usage Instructions
Assembly Instructions
- Use sandpaper to remove residual paint from the lower right corner of the enclosure (inside) to ensure electrical contact.
- Insert the LED dome into the enclosure.
- Install the tube.
- Add a metal washer to the footswitch.
- Insert the circuit board assembly into the enclosure.
- Add jack washers and nuts to the sides. Tighten them securely.
- Add a plastic washer and nut to the footswitch. Tighten them securely.
- Add the bottom cover and screws. Tighten them securely.
Frequently Asked Questions (FAQ)
-
Q: Can I use a different power supply than the specified -9V @130mA?
A: It is recommended to use the specified power supply to ensure optimal performance and prevent any damage to the circuit. -
Q: What is the purpose of the small piece of sandpaper and nut wrench included in the kit?
A: The sandpaper is provided to remove residual paint for proper electrical contact, and the nut wrench is for securing components during assembly. -
Q: Do I need any additional tools for assembling the kit?
A: Apart from the included sandpaper and nut wrench, you may need a screwdriver for tightening the screws during assembly.
Copyrights & Trademarks
Copyright Hagerman Amplification 2024. All rights reserved. No part of this document may be photocopied, reproduced, or translated to another language without prior written consent.
Disclaimer
The information contained in this document is subject to change without notice. Hagerman Amplification shall not be liable for errors contained herein or for consequential damages in connection with the furnishing, performance, or use of this material.
Warranty
Hagerman Amplification warrants this product free of defects in materials and workmanship for a period of 10 years (90 days tubes). If you discover a defect, Hagerman Amplification will, at its option, repair or replace the product at no charge to you provided you return it during the warranty period, transportation charges prepaid to Hagerman Amplification. This warranty does not apply if the product has been damaged by negligence, accident, abuse or misuse or misapplication, has been damaged because it has been improperly connected to other equipment or has been modified without the express written permission of Hagerman Amplification. This warranty is limited to the replacement or repair of this product and not to damage to equipment of other manufacturers. Any applicable implied warranties, including warranty of merchantability, are limited in duration to a period of the express warranty as provided herein beginning with the original date of purchase and no warranties, whether express or implied shall apply to the product thereafter. Under no circumstances shall Hagerman Amplification be liable for any loss, direct, indirect, incidental, special, or consequential damage arising out of or in connection with the use of this product.
Hagerman Amplification
- 1521 Alexander St Apt 1701
- Honolulu, HI 96822
- 808-383-2704
- www.hagamps.com
Description
TUBEKLØN is the world’s first tube-based mythical beast overdrive pedal
interpretation. After deconstructing the classic design, the minimum gain flat
bandwidth feature was removed, instead offering up that sweet midrange boost
as the new minimum gain tone. Based on my NEOKLØN architecture, the
diode/opamp clipping stage was replaced by a triode, as was the summing stage,
which now drives a passive tilt style tone control. The entire circuit is
recreated using five transistors, two triodes, and zero opamps. Tonality is
same as the original, except at high gain, where you get real tube breakup and
sag instead of opamp clipping.
This kit contains a fully assembled and tested circuit board, tube, and
enclosure; you only need to perform final assembly, placing items into
enclosure and buttoning up.
Specifications
Item Specification
Bypass| True
Controls| Gain, Tone, Level
Size| 1590BB
Input Power| -9V @130mA
Kit
Included with your kit should be a small piece of sandpaper and a nut wrench.
If you have a spare (unpowered) 9V power plug, use it to help center circuit
board once installed into enclosure.
Assembly
- Use sandpaper to remove residual paint from the lower right corner of enclosure (inside) such that ground clip near footswitch will make electrical contact.
- Insert LED dome into enclosure.
- Install tube.
- Add metal washer to footswitch.
- Insert circuit board assembly into enclosure.
- Add jack washers & nuts to the sides. Tighten.
- Add plastic washer & nut to footswitch. Tighten.
- Add bottom cover & screws. Tighten.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>