GreenCycle SW-SK1 433MHz Wireless Lights Switch Kit User Manual

GreenCycle SW-SK1 433MHz Wireless Lights Switch Kit

Note: The product pictures are for reference only, subject to our available products

Product appearance

1. 433M Receiver

2. The Receiver can be equipped with the following wireless switches:
   
   86 Wireless Switch
   
   

Product appearance Functional characters of receiver

This device complies with part 15 of the FCC Rules.

Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in are sidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’ s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Installation Warnings

1. The receiver should be installed by a certified electrician.
2. Had better program the switch from receiver for first installation.
3. Please avoid the receiver falling from a height above 1 meter and causing damage.
4. After wiring, don’t let the output live and neutral wires touch together, as this may cause the receiver to short circuit.
5. It is not advisable to install switch on metal surface or receiver in a metal confined cover, metal will shield wireless signal, thus shortening remote control distance.
6. Install the receiver where the human body cannot be directly contacted.

Installment and Dismantle

WARNING!
Please power off before installation!

1. Loosen the screws with a screwdriver
   

2. Each wire end is 8mm exposed and then inserted into the corresponding wiring hole;
   

3. Then tighten the screws with a screwdriver and cover with silicone
   

Wiring method of receiver

WARNING!
Please power off before installation!

Reminder: After installing the receiver, please pair the wireless switch and the receiver before use. For instructions please refer to page 6, with the title called “Pairing”.

Pairing

1. Connect the receiver between the light and the power source.
2. Power on electricity, press and hold the setting button for 2 seconds. When the indicator light flashes, it enters into matching code mode, then loosen your finger.
3. Click the wireless switch button you want to pair to complete the pairing. (The wireless switch can control the light on or off, indicating that the pairing is successful.)
4. It is not recommended that 1 switch button control multiple receivers.

Adding a switch from paired switch

Press and hold the paired switch for about 16s, release when the LED light flashes rapidly, and press the new switch to pair. If the light could be turned on/off, pairing is complete.

Delete the switch code that has been paired

(Please use cautiously)

1. Press and hold the paired key (about 35s);
2. The status of the LED indicator changes as follows: (Fast flash → off )→ (slow flash for 8 times → off) → slow flash (then loosen your grip), and then press the panel key again to complete the code deletion operation.

Delete the paired wireless receiver code

(Please use cautiously)

Press and hold the receiver button for about 10s, loosen your finger when indicator light changes from rapid blinks to slower, press the paired switch panel cannot control the lamps.

Application

(Home, hotel, inn or Factory etc.)

• a. One wireless switch control one receiver.
  

• b. One wireless switch control one receiver.
  

• c. Up to 8 one-gang wireless switches control one receiver.
  

• d. A two-gang wireless switch controls 2 wireless receivers
  

• e. A three-gang wireless switch controls 3 wireless receivers
  

• f. One switch panel controls multiple lamps
  
  

Replace the battery Replace the battery

The methods of open the switch and change battery

Method 1: Push the back hole forward with a small flat blade screwdriver to open the switch

Method 2 : ( if switch attached on the wall) Gently pry at the gap of the lower left with a small flat blade screwdriver, then slide up and down to expand and open.

Change battery: Gently rotate at the position that icon shows with a flat-headed screwdriver and pry up, replace the CR2032 battery (ensure the positive and negative polarity of the battery is correct)

CAUTION:

1. Please replace the battery strictly in accordance with the model requirements in user manual to avoid the risk of explosion;
2. Please put the replaced battery in a safe area and away from children’s reach to avoid burns and death risks caused by accidental ingestion;

Replace the battery

(Model: SW-SK1)

Disassemble the panel

Remove the battery cover shell with a slotted screwdriver to replace the battery (Leave positive pole of the battery upwards), fix and lock the battery cover then cover the panel

(Model: SW-CK1)

1. Pried at the gap with a small flat blade tool then slide up and down to open
2. Push out the battery with flat blade tool then replace CR2032 battery (ensure the positive and negative polarity of the battery is correct)
3. Install the panel and frame again.

Switch disassembly & battery replacement

(Model: SW-AK1)
Open switch and replace battery:

1. Separate the front shell and bottom shell.
2. Open the waterproof cover with a straight screwdriver and remove the silicone.
3. Poke the battery out with a screwdriver in the opposite direction of the arrow then replace the battery. Positive polarity is facing up.
   

Assembly：

1. Place the PCBA and silicone separately into the bottom shell(The groove in the bottom shell correspond to the top chip of the PCBA), then press down with a waterproof shell.
2. Refer to the diagram and insert the front shell into the just installed bottom shell. Notice that the two arrows of the front shell and the waterproof shell are in the same direction.
   

Switch disassembly & battery replacement

(Model: SW-CA2)

Open switch and replace battery:

Gently pry at the gap in the back with a small flat blade screwdriver as illustrated in the figure, then expand and open the switch → Separate the circuit board and waterproof silicone from the bottom cover → Push out the battery with flat blade screwdriver, then replace the CR2032 battery (ensure the positive and negative polarity of the battery is correct)

Assembly：

Tips 1: When assemble, the battery position and the magnetic position must be installed correspondingly, and there is a small hole on the left and right sides of the circuit board, align the small hole with the bottom cover.
Tips 2: Pay attention to align the concave position of bottom cover with the panel, then press gently and close them.

“Open”/”Close” state settings of the receiver used together with traditional switch

Note: The receiver is default in Close state when leaving the factory.

1. Power off electricity, install the receiver as the diagram, and distinguish live from neutral lines.
2. Power on electricity, then program receiver with the switch according to the Learning code Operation chapter.
   

Wiring diagram of adding wireless switch to traditional switch

Magnetic wireless switch

Press ON button: On
Press OFF button: Off

What is the difference between the “Open” and “Close” states when used with a traditional switch?

If the receiver is in the “Open” state, turn on the traditional switch, and the light will be on immediately;

If the receiver is “Close”, turn on the traditional switch, you also need to press the wireless switch to turn on the light.

Whether the receiver is in an Open or Close state, only if turn on the traditional switch could you control lights using the wireless switch.

Setting Open / Close state of receiver
Press and hold setting button for 16s, loosen your finger when the indicator light is continuously bright. (During the 16s, the indicator light will change from quick flash to slower flash, after that, the indicator light will be off, then will be on.)

Specifications of 86 Wireless Switch

Switch panel Lifespan: 600K times
Waterproof level: IPfi6
Battery model: CR2032
Life of the battery: 6-10 years
Standby current: ≤0.01 uA
Working frequency: 433.92 MHz
Wireless Range: Ind00r 3o-100M.
Open Space 300-500M
Fireproof level: VO
Working temperature: – 40 ~+70″C
Working humidity: 0~90%
Storage temperature: – 40 ~ +80 °C

Specifications of Wireless Switch

Waterproof level: IIP66
Battery model: CR2032
Life of the battery: 6-10 years
Standby current:≤ 0.01 uA
Working frequency: 433.92MH.z
Wireless Range: Ind00r 30- S0M .
Open Space 200-400M
Fireproof level: VO
Working temperature: – 40 ~ + 70°C
Working humidity: 0 ~ 90%
Storage temperature: – 40~ +80°C
Model: SW-AK1| Model: SW-CA2
---|---
Dimension: 120x72x12( mm)| Dimension: 6Ox6Ox13 ( m’m)
Switch panel lifespan: 300K times| Switch panel lifespan: 300 Times
Waterproof evel: IP6-6
Battery model: CR2032
Life of the battery: 6-10 years
Standby current: < 0.01 uA
Working frequency: 433.92 MHz
Wireless Range: Indoor 30-S0M .
Open Space 200-400M
Fireproof level: VO
Working temperature: – 40~ +70°C
Working humidity: 0 ~’90%
Storage temperature: – 40 ~+80 °C

Specifications of Receiver

IC : 26805-SWK1
FCC ID: 2ANPS-KS-DB03
FCC ID: 2ANPS-SWNK1R01

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>