Nanjing Body Control Module Remote Control Key User Manual
- May 15, 2024
- Nanjing
Table of Contents
Body Control Module
Remote Control Key
UserManual
Instailation position:
BCM is usually installed on the chassis of the vehicle. located under the co-
driver’s seat, used to control the display screen, anti-theft system and other
functions: The key is a portable piece. used to open the lock, lock, open the
reserve door, etc.
Working mode:
-
the key press the key, the key respectively sends 433.42Mhz. 433.92Mhz, 434.42Mhz 6 frames of data BDM receives high-frequency data from the above three frequency points, and responds to any frame of data, and stops receiving high-frequency data
-
ordinary key PKE The BDM drives the low-frequency antenna at 125HZ to find the key. After receiving low frequency data, the key will respond at 433.42MHz high frequency. The BDM teceives the high frequency response of the key at 433.42MHz.
-
125kKHZ transmission, 434.42MHz receive. periodic Special BDM. common key
-
Start LF poling for the key
First, the key to learning bem
Second. sending 612 51 00 00 00 00, the BDM enters the 6-antenna polling transmission mode, and if the RF of the BDM receives the high frequency signal of the key. the first byte of ID 610 becomes 0x01, and the key cannot be found for 2 seconds. -
Stop polling for keys
Send 612 61 00 00 00 00. BDM stops antenna polling key: 4, 433.42MHz /433.92MH2/434.42MHz reception Special key. normal BDM -
short press the button 1, the key every 5 seconds periodically send 433.92MHz high-frequency data, and then the BDM executes the corresponding action. When button 1 is pressed again (long press), the key will stop sending high-frequency data.
When the button is pressed to send data, the indicator blinks. -
short press button 3, the key every 5 seconds to periodically send 433.42MHz high-frequency data, and then the BDM executes the corresponding action. When button 1 is pressed again (long press), the key will stop sending high-frequency data.
When the button is pressed to send data. the indicator blinks. -
Press button 4. The key periodically sends 434.42MHz high-frequency data every 5 seconds, and the BDM executes corresponding actions. When button 1 is pressed again (long press), the key will stop sending high-frequency data. When the button is pressed to send data, the indicator blinks.
DESCRIPTION
BCM and remote control keys are designed and produced by Nanjing
CETC-Motor Co., Ltd. Their main functions include anti-theft system, one key
start, and other functions, providing one-stop technical solutions for
automotive manufacturers. Our company was established on August 25, 2006 and
has been deeply involved in the automotive electronics industry for 17 years.
This product is a body controller that is shipped with the entire vehicle. If
there are any quality issues, we need to communicate with the vehicle company
for compensation. Our company will communicate with the automotive company for
compensation issues.
Technical characteristics:
The maximum temperature for the BCM and key of this product is -40 ‘ -90 C,
and the working temperature is -40 ‘C -80 C.
Working principle;
PKE is a handset that is operated by vehicle user. PKE sends encrypted data to
BCM by RF antenna based on 433.92MHz/ 433.369MHz.
The BCM system send encrypted data to PKE by LF antenna or IMMO antenna based
on 125KHz. and receive 433.92MHz/ 433.369MHz encrypted data from PKE, and
execute the authentication. If the result of authentication is pass, BCM will
perform the action in response.
Instructions for use
Customers are prohibited from disassembling without authorization. If there is
any damage, professional personnel can be consulted for disassembly and
repair. According to the after-sales repair requirements of automotive
companies, accurate and legitimate accessories can be found for replacement
and debugging. If damage is caused by unauthorized disassembly, our company
will not compensate. Please note to the customer.
Body Control Module
1.1.Product information
Module No.: BCO4
Voltage Range: DC 9-16V
Working frequency: TX: 125kHz
RX: 433.92MHz/433.369MHz
Modulation type: ASK for 125kHz
Transmitter maximum output power: 13 dBuA/m @10m
1.2. Manufacturer’s plate
Remote Control Key – 11652820
1.3. Product Information
Module No.: 11652820
Voltage: DC 3V (CR2032)
Working frequency: TX: 433.92MHz and 433.369MHz
RX: 125kHz
Modulation type: FSK for 433.92MHz and 433.369MHz
Transmitter maximum output power: -19 dBm
1.7. Usage/Setting Steps
This component is an automotive accessory, and the usage environment and
instructions are subject to the final automotive manufacturers manual. The
setting method can be found in the automotive manual
FCC Statement
Changes or modifications not expressly approved by the party respons ible for
compliance could void
the user’s authority to operate the equipment.
This device complies with part 15 of the FCC rules. Operation is subje ct to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause un desired operation.
NOTE: This equipment has been tested and found to comply with the | imits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against ha rmful
interference in a residential installation. This equipment generate s uses and
can radiate radio frequency energy and, if not installed and used in accord
ance with the instructions, may cause harmful interference to radio co
mmunications. However, there is no guarantee that interference will no t occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to c orrect
the interference by one or more of the following measures: * Reorient or
relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help impo rtant announcement
Radiation Exposure Statement
This device is also designed to meet the requirements for exposure to radio
waves established by the Federal Communications Commission (USA).
This device Was tested for typical near Body operations kep Ocm away, and this
device complies with FCC radiation,exposure limits set forth for an
uncontrolled environment.
Manufacturer: Nanjing CETC-Motor Co.,Ltd.
Address: Floor 18th A Zone Building 1 Guorui, No.359 Middle Jiangdong Rd.,
Jianye District, Nanjing City,
210000 Jiangsu P.R. China
Documents / Resources
|
Nanjing Body Control Module Remote Control
Key
[pdf] User Manual
Body Control Module Remote Control Key, Body, Control Module Remote Control
Key, Module Remote Control Key, Remote Control Key
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>