Nanjing Xia Ding Electronic Technology Q Series Q1212 Remote Control User Manual

Safety·Reliability·Efficiency
User’s Manual for Q Series Remote Control

Product Description

LCC industrial remote controller series is specially designed for the control of industrial machinery and equipmen1; It’s widely used in wireless remote control of a variety of industrial equipment, such as various cranes, tower cranes, conveyors, and other crane equipment the main features are as follows:

1. A total I of 200 sets of「emote control channels can be adjusted, completely replacing the traditional quartz single-channel, solving the problem that is easy to break and hard to get the channel.
2. The receiver has the function of an automatic search transmitter channel: the use of a replacement transmitter do not need professional equipment pairing, safe, it is simple and efficient.
3. More than 1 million sets of non-repeatable ID codes: superior to other industrial wireless remote controls on the market, the LCC family never repeats ID codes
4. With advanced microprocessors: fast, high security, high accuracy, and 1 00% correct coding and decoding
5. More than 200 function settings: the transmitter and receiver have more than 200 function settings, can fully meet the various work needs of customers.
6. The whole series of products are completely compatible with software and hardware, which avoids customers from storing too many spare parts. Customers can be prevented from unnecessary large inventory expenditures.
7. Rugged transmitter button: transmitter keystroke can reach 2 million times of continuous operation pressing, absolutely durable.
8. Power-saving design: the transmitter only needs two No. 5 “AA” alkaline batteries to operate and use for more than 100 hours.
9. Reinforced fiber plastic case: the durable case for transmitter and receiver to prevent damage caused by strong impact and frequent drop.

Product Graphic Of Transmitter

A. Transmitter

1. Appearance graphic introduction

2. Emergency stop button

3. Startup/ bell

4. Button

5. Button

6. Button

7. Button

8. Press

9. Button

10. Button

11. Button

12. Button

13. Button

14. Button

15. Button

16. Hanging ring

17. SN/CH code /channel

18. battery cover

Operation Instructions

Operating of transmitter
1. General operating procedures

1.  Rotate the red emergency button located in the upper left corner of the transmitter clockwise or counterclockwise, and the button will pop up.
2. Press the green button and the green status means the start of the flashing remote control.
3. After startup, check the STATUS light cn the transmitter to confirm that the system is normal under normal conditions, a green light will flash when the button is pressed.
4. After completing the above operation procedures, press any button on the transmitter tc control the crane or other equipment. 5). When the device is to be stopped, press the red emergency stop button of the transmitter immediately, and the receiver can cut off the total power of the device to stop the device. If you want to restart, redo the boot action, as in the above procedures 1. and 2.

2. Replace the battery
Please open the battery cover on the back of the transmitter And use the No. 5 “AA” Alkaline batteries, After replacement, lock the battery cover to prevent dirt from seeping into the transmitter

Simple Diagnosis / Troubleshooting For Transmitter

Please check whether the remote control handset is in good condition before using the remote control. When it is found that it cannot be operated normally, you can follow the steps below to perform simple lamp diagnosis and troubleshooting. If the following is still not normal, please inform the dealer for repair.

Red and green without indication
Remarks: press any button without a light indicator| Red light flashing 1 long bright| The green light is flashing
---|---|---
Diagnosis and failure analysis
i No power.
i i boot mode.| Diagnosis and failure analysis
i The battery spring piece is dirty.
ii The battery power is insufficient. iii The battery itself is damaged.| Diagnosis and failure analysis
i The receiver without sufficient power
ii The receiver without input power.
Solution
i Please check the battery itself, damaged or not. Or the battery joint dirt causes poor contact.
ii Please replace the brand new battery and start the transmitter again.
iii rechargeable battery needs to be charged or replaced with a new one.| Solution
i Please check if the battery itself is damaged or not.
ii Check if the battery spring is dirty or not.
iii Please replace the brand new battery and start the transmitter again.| Solution
i Please check the power of the receiver
i i Please check the fuse of the receiver

Technical index

Specification Table Of Transmitter

Working Temperature ( regardless of
battery temperature )| -35t..+75
Net weight ( with battery ) g| 380g
Case Material| PA6+30% GF
Protection Level| IP65

Receptor Specification Table

Product Warranty

Quality assurance
LCC guarantees that this product will meet the technical specifications shown in the factory when it leaves the factory. As long as it is installed correctly, it can be used normally.

During the Warranty time,
This product enjoys a one-year shelf life from the date of shipment, and if it is during the warranty period, the non-human damage LCC is responsible for maintenance. Any product that requires repair must be sent to the service designated by LCC for repair. The customer is responsible for the one-way shipping cost of the product to the service, and LCC will bear the return fee and return the product during the warranty period.

Unincluded items
The above warranty does not include Wear-and-tear parts such as buttons, relays, fuses, and batteries. Improper use of machine errors, irresistible causes, natural factors, inadequate maintenance, operating environment, and specifications are ignored. Unauthorized changes, incorrect use, or fault damage caused by the customer setting the interface.

Remarks
There are no other warranties, express or implied, regarding the above warranty. The repairs provided by the warranty are the sole compensation of the customer and LCC is not responsible for any direct, indirect, special, accidental, or causal liability.

notes

General considerations

• Personnel who have not been professionally trained shall not disassemble the machine, otherwise, it may be damaged and cause casualties.

• This manual is for reference only. Please consult the agent for detailed technical questions.

• This machine has been closely tested before leaving the factory, but shall not be used in dangerous and potentially damaging circumstances, After use, the total power supply of the equipment should be turned off, the power supply of the receiver should be cut off, and the key switch of the transmitter should be removed.

• The transmitter should be placed in a safe place, and personnel should not be randomly pressed to avoid accidents.

• Equipment should have total power relays, limit switches, and other safety facilities.

• It should be discontinued in the event of lightning strike or interference.

• Ensure that the transmitter battery is fully charged and the receiver voltage is normal.

• When installing or repairing, turn off the total power of the equipment and the power supply in the receiver to avoid electric shock.

• If necessary, the manufacturer will change the machine appropriately. Therefore, the content will be adjusted at any time based on the new machine without notice. Operator precautions

• Users must have received 0 series of operation training to familiarize themselves with the operation mode.

• The operator must be in good health, in good spirits, be able to identify and judge the safety of the operation and have a qualification certificate.

• series of the rugged transmitters can be quite resistant to impact and weather resistance, but too much or deliberate collision, extrusion, it may still be damaged.

• The operation user should pay attention to the indicator light on the transmitter. If the red light continues to flash, there may be an abnormality or a fault condition, or the battery may be exhausted. At this time, stop the operation immediately and replace the battery light. It can be operated after normal.

• If you find that the equipment is seriously disturbed, you must stop the operation immediately.

• If you do not use the remote control for a long time, you must remove the battery inside the transmitter.
  Installation Precautions

• When installing the receiver, turn off the total power supply of the equipment and ensure that the power supply is cut off so as not to be electrocuted.

• Receiver mounting position should be selected to avoid contact with sparks, such as remote motor, cable, inverter high voltage wiring, etc. Other sources of interference.

• The fixed lock must be determined when the receiver is installed to avoid loosening and falling off the receiver. Ensure understanding of the distribution of the crane and the setting of the remote control function (including relay output) to avoid causing incorrect wiring.

• The receiver should not be installed in the electronic control box. the correct way to install the receiver is to fix the receiver in the appropriate position at the top (or outside) of the electronic control box, and then put the receiver output cable into the electronic control box to make the appropriate wiring.

• There are 4 billion sets of security codes in this series of remote control. The security code settings are different before shipment. Please check if there is remote control of the same channel within 100m range during installation to avoid interference.

Wiring Diagram

LCC-Q Series Wireless Pairing

The pairing of Transmitter and receiver:

1. The pairing mode of the receiver: the receiver is powered on and the small black button “3 seconds” is held down on the receiving motherboard to wait for the traffic lights to flicker alternately.
2. The pairing mode of transmitter: when the transmitter with power, presses the emergency stop, alternately presses ” up ” and ” down ” four times, then the lights flash red and green alternately.
3. The transmitter presses the green start button ( START) Don’t let go, press ” Down “, when all the lights are off, the receiver code and settings are successfully downloaded to the transmitter

FCC Cautions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>