ACERBIS 24021 Exhaust Heat Shield Installation Guide
- May 15, 2024
- ACERBiS
Table of Contents
ACERBIS 24021 Exhaust Heat Shield
Product Information
Specifications:
- COD. 500007707 REV.1
- X-EXHAUST PARACALORE X-EXHAUST ACERBIS PARTS
- A – 1 pc
- B – 2 pcs
- C – 2 pcs
- D – 2 pcs
- E – 2 pcs
- F – 4 pcs
Product Usage Instructions
Step 1: Assembling Threaded Plates and Hose Clamps
- Insert the threaded plates (C) into the hose clamps (B).
- Attach the hose clamps with threaded plates to the muffler loosely.
Inserire la facetta (B) nella piastrina (C) e posizionare sulla marmitta. Stringere senza serrare completamente.
Step 2: Attaching Head Shield
- Attach the head shield (A) to the muffler using the supplied bolt (D), bushing (E), and washers (F) as shown in the figure.
Fissare il paracalore (A) tramite le boccole (E), le rondelle (F) e le viti (D) in dotazione. Stringere senza serrare completamente.
Warning:
MIN 8mm
WARNING!
Contact Information:
- Europe: ACERBIS ITALIA S.P.A. VIA SERIO, 37 24021 ALBINO (BG) ITALY
- U.S.A.: ACERBIS U.S.A. INC. MAIL P.O. BOX 2030 SUN VALLEY, ID 83353 SHIP 110 LINDAY CIRCLE KETCHUM, ID 83340 U.S.A.
- United Kingdom: ACERBIS U.K LTD UNIT 2 LUTON ENTERPRISE PARK SUNDON PARK ROAD LUTON, BEDFORDSHIRE LU3 3GU GREAT BRITAIN
FAQ:
Q: How tight should I secure the components?
A: Secure the components loosely without fully tightening to allow for
adjustments during final assembly.
ACERBIS PARTS
ASSEMBLY
STEP 1
Insert the threaded plates (C) into the hose clamps (B) and then attach to the
muffler loosely.
STEP 2
Attach the head shield (A) with the supplied bolt (D), bushing (E) and
washers (F) as shown in figure. Tighten loosely.
STEP 3
Arrange the shield and clamps so that the shield is a minimum of 8 mm away
from the exhaust pipe and tighten the clamps (B).
Then tighten the head shield to the clamps and torque to 4Nm.
After one hour of use, check the tightness of the clamps and shield and
tighten if needed.
STEP 4
If it’s not possible to have a minimum distance from the exhaust pipe of
8mm, it is possible to deform the protection, tighten the clamps where the
protection hole is aligned and then tighten the screw.
WARNING!
Use Acerbis’ products at your own risk. Check the safety of your device before you ride. Be sure that you follow the instructions for installing the Acerbis‘ products. Do not ride if there is missing or damaged hardware. If this is the case, take the item immediately back to your dealer. Make sure the throttle and other controls are free every time you ride. Not following these instructions and warnings could lead to interference with the controls, loss of control, and accidents. Acerbis recommends that installation must be done by a licensed mechanic and that only Acerbis’ original parts are used during installation. Acerbis makes no guarantees or representations, express or implied, regarding the fitment of its product for any particular purpose. Acerbis makes no guarantees or representations, express or implied, regarding the extent to which its products protect individuals or property from injury or death or damage.
EUROPE
ACERBIS ITALIA S.P.A. VIA SERIO, 37
24021 ALBINO (BG) ITALY
U.S.A.
ACERBIS U.S.A. INC. MAIL P.O. BOX 2030 SUN VALLEY, ID 83353 SHIP 110 LINDAY
CIRCLE KETCHUM, ID 83340 U.S.A.
UNITED KINGDOM
ACERBIS U.K LTD
UNIT 2 LUTON ENTERPRISE PARK SUNDON PARK ROAD
LUTON, BEDFORDSHIRE LU3 3GU GREAT BRITAIN
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>