COMMAND ACCESS MLRK1-ARW Field Installable Motorized Latch Retraction Kit Installation Guide

May 15, 2024
COMMAND ACCESS

COMMAND ACCESS MLRK1-ARW Field Installable Motorized Latch Retraction Kit

COMMAND ACCESS MLRK1-ARW Field Installable Motorized Latch Retraction
Kit

INSERT INSTRUCTIONS

The Command Access MLRK1 is a Field-installable motorized latch-retraction kit:

  • MLRK1-SGT – Sargent 80 series devices
  • MLRK1-ARW – Arrow 1000 series devices

KIT INCLUDES

A. 1 – Motor Mount
B. 1 – 40801 – Phillips head screw
C. 1- 50944 – Molex pigtail
D. 2 – 40060 – Cable tie
E. 2 – 40059 – mounting pad
F. 1- 60368/51186 – remote mm4s module
G. 1 – 50741 – remote module cable
Kit Includes

INSTALLATION VIDEO

SPECIFICATIONS

  • Input Voltage: 24VDC +/- 10%
  • AVERAGE low Torque LATCH RETRACTION CURRENT: 900 mA
  • Average high torque latch retraction current: 2A
  • Average holding current: 215 ma
  • Wire gauge: Minimum 18 gauge
  • Direct wire run – no relays or access control units in-between power supply & module

Recommended Power Supplies: Use a power limited class 2 power supply
All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. If you plan on using a non-Command power supply it must be a filtered & regulated linear power supply

TECHNICAL INFORMATION

Technical Information

Step 1- Select your preferred torque mode (ships in standard torque) Press the device push pad to the desired
setting. (Recommend to fully depress and release 5%, giving the device room for changing door conditions.)
Step 2- While depressing the push pad, apply power. (i.e. presenting the credential to the reader).
Step 3- Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the 3 steps.
Step 4- Once you found the correct location, turn PTS switch to OFF position.

TROUBLESHOOTING & DIAGNOSTICS

Beeps Explanation Solution
2 Beeps Over Voltage > 30V unit will shut down. Check voltage & adjust to 24

V.
3 Beeps| Under Voltage| < 20V unit will shut down. Check voltage & adjust to 24 V.
4 Beeps| Failed Sensor| Verify all 3 sensor wires are installed correctly. Replace sensor if problem persists by contacting office.
5 Beeps| Retraction or dogging failure| After 1st fail: 5 beeps then immediately attempts to retract again.
After 2nd fail: 5 beeps with pause in-between for 30 seconds then device attempts to retract again.
After 3rd fail: 5 beeps every 7 minutes, device will not attempt to retract.
To Reset: Depress bar for 5 seconds at any time.
6 Beeps| PUSH TO SET| Device is recording it’s new position and power mode after the 6th beep.

INSTALLATION INSTRUCTIONS

  1. Flip over device & remove (4) screws securing push pad assembly to housing.
    Installation Instructions

  2. Slide Push Pad off Exit Device Housing.
    Installation Instructions

  3. Locate the FRONT Activating Bracket.
    Remove original mounting bracket by pushing out PIN.
    Installation Instructions

  4. Install Point of Front Activating bracket into opening of motor’s attaching bracket.
    It should rest on top of the nylon roller.
    Installation Instructions

  5. Once the point is in the opening, depress the push pad until the holes on the activating bracket & motor mount line up. Re-install factory pin.
    Installation Instructions

  6. Connect MM4S Cable to back of motor’s (3) Pin & (4) Pin connectors.
    Installation Instructions

  7. Slide Push Pad & Motor Kit back into housing.
    Be cautious of MM4S cable wires.
    Installation Instructions

  8. Make Sure MM4S Cable is routed OVER the back activating bracket.
    Installation Instructions

  9. Once passed the back activating bracket, flip device over & line up existing holes with mounting bracket inside. Re-install (4) screws.
    Installation Instructions

  10. Plug-in cable’s (4) Pin TOP port & (3) Pin BOTTOM port into MM4S ports.
    Installation Instructions

  11. Using double sided tape, secure MM4S to inside of the back of exit device housing.
    Connect Molex Pigtail. Add Mounting Pad & cable tie to secure cable wires.
    Installation Instructions

  12. Connect to Power & Set the “Push to Set Adjustment” following the steps below.
    Installation Instructions

Step 1- Select your preferred torque mode (ships in standard torque) Press the device push pad to the desired setting. (Recommend to fully depress and release 5%, giving the device room for changing door conditions.)
Step 2- While depressing the push pad, apply power. (i.e. presenting the credential to the reader).
Step 3- Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the 3 steps.
Step 4- Once you found the correct location, turn PTS switch to OFF position.

Customer Support

U.S. Customer Support
1-888-622-2377
Visit our website for more details
www.commandaccess.com
Canada Customer Support
1-855-823-3002

Logo

Documents / Resources

| COMMAND ACCESS MLRK1-ARW Field Installable Motorized Latch Retraction Kit [pdf] Installation Guide
MLRK1-ARW, MLRK1-ARW Field Installable Motorized Latch Retraction Kit, Field Installable Motorized Latch Retraction Kit, Installable Motorized Latch Retraction Kit, Motorized Latch Retraction Kit, Latch Retraction Kit, Retraction Kit, Kit
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

COMMAND ACCESS User Manuals

Related Manuals