TR039 Pellet BBQ Smoker Grill User Manual
- May 15, 2024
- TR039
Table of Contents
TRO39 Pellet Grill Function Specification
Product feature description:
- Heat Source : Burn z6mm Wood Pellet ,calorific value about 4,200-4,800Kcal/Kg ;
- Input Voltage : AC 90V~230V 50HZ~60HZ;
- Temperature signal probe: PT1000;
- Total load about 235W,Length of Controller Wire about 450mm,Black Wire connect to power supply,Yellow Wire connect to Fan,Purple Wire connect to the Hot Rod,and the Red Wire connect to the auger motor.
Function and usage:
2.1 Detailed description of electrical parameters:
- Input Voltage—- AC/120V 60hz.
- Rated power—— 245W.
- Maximum output power—— Motor 50W Fan50W Hot Rod 250W.
- Display temperature——— Fahrenheit display range 30F- 610F, error range +10F.
- Workplace temperature—– -10°C~50°C.
- Storage temperature—– -20°C~60°C .
- Pressure coefficient——— AC 1.5KV 0.5MA.
- Service life ———- 50,000 Hour Under normal working environment.
2.2 Appearance:
Panel : 14cm X 7cm
Double PCB structure, Effectively reduce interference.
2.3 Control panel settings
- OFF Gear (Shut Down Cyle);
- Smoker Gear(SMOKE) ;
- 180°F Gear ;
- 225°F Gear ;
- 250°F Gear ;
- 275°F Gear ;
- 300°F Gear ;
- 325°F Gear ;
- 350°F Gear ;
- 375°F Gear ;
- HIGH Gear(450°F) ;
- Probe Selector.
2.4 In smoke mode, there are 6 states: PO ~ P5
Press JK1Button to Switch to P” Gear, The position of jk1 key is shown in the
figure below. 
2.5 Instructions
- Black Wire connect to power supply,Yellow Wire connect to Fan,Purple Wire connect to the Hot Rod,and the Red Wire connect to the auger motor.
- Switch Knob into SMOKE Gear from OFF Gear, Digital Screen display Actual Temperature, ON, FAN, AUGER MOTOR, HOT ROD.
- The fan returns to off, delaying operation for 10 minutes and shutting down.
- Each time it starts from off, it will automatically enter the ignition program. The ignition mode is that the motor works for 4 minutes and 15 seconds, and the Hot Rod works for 6 minutes. When the temperature of the probe of the Hot Rod is less than 150 degrees Fahrenheit in the Barbecue mode, the system will automatically restart the Hot Rod to work for 6 minutes.
- Rotate to smoke to display the actual temperature.
- When the switch is turned to the COOK Gear, the gear value will flash for 5 times and return to the temperature display.
- Press the “P” Gear Button once to display the original gear value, and press it again to increase step by step by 1, and return to the original gear value after 3 seconds without action.
- After the barbecue is finished, the gear is turned back to off, and the fan still needs to work for 10 minutes to complete the combustion of fuel in the furnace.
2.6 Work Mode
Smoke Mode :
Switch to Smoke Gear, Then the auger motor works in “P” gear mode
Cook Mode :
Cook Gear Temperature can be set, There are 180°F , 225°F, 250° F ,275°F,
300°F , 325°F , 350°F ,375°F Gear, HIGH(450°F).When the display temperature is
lower than the gear value, the auger motor will feed for a long time; when the
displayed temperature is higher than gear value, the motor will work in “P”
gear mode, and the feeding time and stop time can refer to 2.4. If the
temperature is too high (higher than 550 ° f), display HEr, all equipment will
be shut down.
2.7 Fault description
- HEr, Represent high temperature, Shut all equipment down.
- Er1, Represent Probe hitch, Shut all equipment down.
- LEr, Represent the hot rod has been working for more than 20 minutes for a long time, all equipment shall be shut down to indicate the Overheat protection status.
2.8 Probe Usage
This product uses PT1000 probe, which can be connected to two probes,
PROBE1 and PROBE2. When using, install the probe, and press the probe selector
button, the probe you are connected to will be displayed (PO1 or PO2, if there
is no probe connected, press the button will not respond), wait for 2 seconds,
the temperature detected by the probe will be displayed, flashing five times
before jumping back to furnace temperature.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>