EnjoySeating 6702 Home Office Desk Chairs Instruction Manual
- June 14, 2024
- EnjoySeating
Table of Contents
EnjoySeating 6702 Home Office Desk Chairs Instruction Manual
Assembly Guide
Congratulations, you are now the owner of a brand new home & office chair!
To best enjoy the comfort of the chair, you have to put it together first! This assembly guide will take you through the assembly process. To make sure the assembly goes well, please follow the instructions, and especially the important safety information.It is possible to assemble the chair on your own, but it is recommended to have a second person to make it easier and safer.
Please check if there are any missing parts from the package before starting. If there is any issue, please don’t hesitate to drop us an email and we’ll help you out ASAP. If you run into any difficulty when assembling the chair, remember to check out the assembly video to see if you’ve missed anything. If you’re unable to resolve the problem, just send us an email and our support team will assist you.
WARNING
To ensure proper assembly, please follow all steps and use all parts. Failure to follow this warning can result in serious injury to yourself or others
Package List
-
(A)*1 Backrest
-
(B)*1 Seat Cushion
-
(C)*2 Armrests
-
(D)*1 Mechanism
-
(E)*1 Gas Lift
-
(F)*1 Base
-
(G)*5 Legs
-
(H)*5 Casters
-
(J)*4 Bolts for mechanism
-
- (M)*1 Wrench
-
(N)*1 Hood
Assembly Instruction
Step 1
Turn the Base (F) upside down,then insert Base Legs (G) one by one to Base.
Use the Wrench (M) to screw Ten Bolts M6x10(I) into the pre-drilled screw
holes to fix the Base and the Base Legs.
Step 2
Press the Casters (H) into the holes at the end of each Base Leg.
Insert the Gas Li� (E) and the Hood (N) into the center hole of the Base.
Step 3
Align the backrest (A) to the armrest, and insert the backrest into the armrest (C).
Find the screw holes on the back of the backrest and screw the bolts M6x20(L) in.
All bolts do not need to be �ghtened, they only need to be fixed in half.
NOTE: The seat cushion and the mechanism is divided into front and back,
and the armrests are divided into one and right one. Please observe carefully.
Step 4Turn the Seat Cushion (B) upside down and align the hole position of the Armrest (C) with the pre-drilled hole position under the Seat Cushion.
Attach the Armrest (C) to the Seat Cushion (B) with Four Bolts M6x35(K), using the Wrench (M) to tighten them.
100% tghtened the Bolt (L)* 4 to fix the armrest and backrest.
Step 5
Attach the Seat Cushion (B) to the Mechanism (D) , Use the Wrench (M) to screw
Four Bolts M6x16(J)
****
Attention : The mechanism tension knob should be in the front of the cushion.
Step 6
Align the hole of mechanism to the gas lite, and insert the upper part into
the gas lift.
CAUTION: Make sure all bolts and screws are fully tightened before using chair.
Instructions For Use
Seat Height: Paddle-shaped lever on the right side
To raise:
While taking your weight off chair, life lever up.
To lower:
While seated, life lever up.
At the proper height, your feet should rest flat on the floor.
Operating the rocking function
Rotate the knob under the seat cushion to adjust the shaking amplitude.
To let your chair back, pull the control handle out
To stop your chair from tilting, sit forward, then push the control handle in.
Safety And Maintenance
- Do not stand on the chair, Do Not use the chair as a stepladder.
- Use this product for seating one person at a tme.
- Do not use the chair unless all bolts and screws are firmly secured.
- Avoid contact with sharp objects to prevent puncturing the fabric.
- Every 6 months, check all bolts and screws to ensure they are tight.
- To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
- Chair weight limit not to exceed 300 lbs.
Safety Information
- Sit in the center of the chair, with your back to the backrest
- Do not sit at the front edge of the chair
- Do not stand on the chair
- Do not use the chair with more than one person
- Do not push the chair around when a person is sitting in it
- Do not push down on the backrest when a person is reclined
- Do not place all your weight on only the backrest
Limited Warranty
During warranty, if the following malfunc�on occur during normal use, please feel free to contact us by email, our customer service email: ( enjoyseatingservice@gmail.com ; anjiyike@163.com).
Warranty terms
| Object part | Malfunction | Warranty time |
|---|---|---|
| Mechanical structure | Malfunction and damage of cushions, backrest and | |
| casters | Two years from the date of purchase | |
| Structural parts | Deformation, damage, corrosion, etc of the main steel | |
| structure | Two years from the date of purchase |
Warranty items are applicable to all models, please feel free to contact us after the warranty expired’s repairing.
0ut of Guarantee
The following conditions are not included in the warranty.
- Malfunction or damage caused by accident, fire, flood or natural disaster.
- Malfunction or damage caused by misuse, abnormal use, improper repair or personal modification.
Write to our respected customers:
In the process of chair development, we pay most chair comfort, followed by appearance and function.Before mass production of chairs, we will invite a large number of people to experience the comfort of chairs, from workshop staff to office staff.
In combination with the user experience, we constantly adjust the details of the chair, from the choice of fabric, the thickness and density of sponge, as well as the width, depth and angle of the chair, to achieve the most comfortable sitting experience.
We hope that our efforts will enable you to sit on our chair and be really comfortable and relaxed.
Feel free contact with us if you have any questions
Your sincerely
Enjoy seating
enjoyseatingservice@gmail.com
anjiyike@163.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>